Horstmann CentaurPlus C17 User Manual page 2

RESETTING THE PROGRAMMER
Electronic equipment can in some circumstances be affected by electrical interference. If the
programmer's display becomes frozen or scrambled; or if you wish to revert back to the default time
settings please use the following procedure.
Press the SET and SELECT buttons together
then release the buttons and the programmer
will return to preset factory settings.
T T h h e e s s i i m m p p l l e e i i n n s s t t r r u u c c t t i i o o n n s s b b e e l l o o w w a a r r e e d d e e s s i i g g n n e e d d t t o o h h e e l l p p w w i i t t h h t t h h e e p p r r o o g g r r a a m m m m i i n n g g o o f f t t h h e e u u n n i i t t . .
SETTING DAY AND TIME OF DAY
Press the SET but- Use PLUS
ton until the SET indi- and MINUS
Press
buttons to
cator is next to the
ENTER
CLOCK position. adjust day
M T W T F S Su
RUN
12:00
CLOCK
PM
PROG
D D E E F F A A U U L L T T T T I I M M E E S S E E T T T T I I N N G G S S
The default factory settings
are shown, however if you
MON-FRI
wish to change these
proceed as instructed below.
SAT/SUN
SETTING THE ON AND OFF TIMES
Press SET button
Use PLUS
until the SET indicator is
and MINUS but-
next to the PROG tons to adjust
position
day
Repeat this
programme on any other
Press
process for 2nd
day of the week use the
ENTER
and 3rd settings
PLUS and MINUS buttons to
select day and press COPY
M T W T F S Su
RUN
DAY
CLOCK
PROG
Should you encounter any problems, please refer to the
Q Q u u e e s s t t i i o o n n a a n n d d A A n n s s w w e e r r section located on page 4.
P P a a g g e e 2 2
SET
Use
PLUS and
ton until the SET indi-
MINUS
Press
buttons to
ENTER
adjust time
M T W T F S Su
RUN
6:35
CLOCK
PM
PROG
1st ON 1st OFF 2nd ON 2nd OFF
6:30 8:30 12:00 12:00
A A M M A A M M P P M M P P M M
7:30 10:30 12:00 12:00
A A M M A A M M P P M M P P M M
Use PLUS and
MINUS
Press Press
buttons to adjust
ENTER ENTER
the 1st ON time.
If you require this
Programme the
remaining days.
M T W T F S Su
RUN
6:30
CLOCK PROG
AM
1
ON
Programming ON/OFF times
If a period is not required it can be cancelled by setting the ON and OFF settings to the same
time. Example ON 10:00am OFF 10:00am
SELECT
The SET indicator must remain in the RUN position for the following instructions.
Press the SET but-
Press SELECT once.
Programme goes from
cator is next to the
AUTO to ALL DAY
RUN position.
Unit will operate from
first ON until last OFF
period
M T W T F S Su
6:35
PM
3rd ON 3rd OFF
4:30 10:30
P P M M P P M M
5:00 11:00
P P M M P P M M
Use the PLUS
and MINUS but-
tons to adjust the
1st OFF time.
Press SET button
until the SET
indicator is returned
to RUN position
Press ADVANCE button once
to move to the next
ON/OFF time
INFORMATION AND ADVICE
SPECIAL FEATURES
Press SELECT again. Press SELECT again.
Programme goes from Programme goes from
ALL DAY to 24 HRS
Unit will be
continuously ON
M T W T F S Su
AUTO AUTO
6:35
ALL DAY ALL DAY
PM
24 HRS 24 HRS
OFF OFF
BOOST FUNCTION
-
1hour temporary override
Press BOOST button: At any time during a BOOST
period press BOOST again to
Your System will be Boosted return to normal program-
for 1 hour ming
ADVANCE FUNCTION
-
Brings forward next on or off operation
To cancel the advance press the ADVANCE
button again. This will return the unit to
its normal programme
Press SELECT again.
Programme goes from
24 HRS to OFF OFF to AUTO
Programmer will return
Unitl will be
to normal ON and OFF
continuously OFF
times
M T W T F S Su
M T W T F S Su
AUTO AUTO
6:35 6:35
ALL DAY
ALL DAY
PM
PM
24 HRS 24 HRS
OFF
OFF
M T W T F S Su
RUN AUTO
6:35
CLOCK ALL DAY
PM
PROG 24 HRS
BOOST
OFF
M T W T F S Su
RUN AUTO
6:35
CLOCK ALL DAY
PM
PROG 24 HRS
ADVANCE OFF
P P a a g g e e 3 3