Summary of Contents for EMUGE Softsynchro 1/ PGR
- Page 1 ® Operating instruction for the collet holders type ® Softsynchro 1/ PGR ® Softsynchro 3/ PGR Date of edition: 01.04.2012 Stage of alteration: 1 Please keep this for future use!
- Page 2 Operating instruction for collet holder ® type Softsynchro / PGR ® powRgrip is a registered trademark of REGO FIX AG.
-
Page 3: Table Of Contents
Operating instruction for collet holder ® Type Softsynchro / PGR ® Contents: Application range and technical data ............3 Application range, determined use................. 3 Specifications......................4 Safety instructions....................4 Dimensions and technical data ................5 Putting the collet holders into operation ..........6 Unpacking...................... - Page 4 Operating instruction for collet holder ® type Softsynchro / PGR ® Warnings, symbols In these operating instruction the following symbols are used: Marks special instructions, rules and prohibitions, which are important in order to avoid any damage. Please observe these instructions! Marks application instructions and other useful information.
-
Page 5: Application Range And Technical Data
Operating instruction for collet holder ® Type Softsynchro / PGR ® 1 Application range and technical data Application range, determined use ® The collet holders type Softsynchro /PGR are used on CNC machining centres with synchronous control. The integrated minimal length compensation on tension and compression compensates arising minimal pitch differences between synchronous spindle and tool which would lead to high thread flank friction forces. -
Page 6: Specifications
For collet holders with cylindrical shank: The standardized cylinder shank acc. to DIN 1835 B+E allows a simple adaptation with the required adaptation shank. For adaptation shanks please refer to the EMUGE main catalogue. Quick clamping: tool change within 10 seconds Clamping true to the µ: high concentricity guarantees reliable and repeatable tool life... -
Page 7: Dimensions And Technical Data
3/ PGR 8–16 PGR25GB – ¾) Further outer dimensions depend on the required shank. The dimensions may be taken from the EMUGE main catalogue or may be given by your EMUGE-representative. Length compensation on compression Length compensation on tension Edition: 01.04.2012... -
Page 8: Putting The Collet Holders Into Operation
Operating instruction for collet holder ® type Softsynchro / PGR ® 2 Putting the collet holders into operation Unpacking Take the collet holder from the packing Clean the collet holder with a duster to remove any conservation oil Clean the collet holder as described in the cleaning directions, see chapter 2.6.1, page 9. -
Page 9: Assembly Of The Coolant-Lubricant Pipe For Collet Holders With Shank Type Hsk (Hollow Taper Shank Din 69893A)
2. Slide on thread nut. c) Mount coolant-lubricant pipe in the shank Required tool: Assembly wrench, choose appropriate assembly wrench for the shank size (For the assembly wrench please refer to the EMUGE main catalogue, category accessories) 1. Put assembly wrench on the Groove... -
Page 10: Collets
Operating instruction for collet holder ® type Softsynchro / PGR ® Collets 2.5.1 Application The adaptation of the tool is executed via collets type PGR and/or PGR-GB. These powRgrip collets have a taper shank with plane contact surface and a central bore for the tool shank. -
Page 11: Cleaning Directions
Operating instruction for collet holder ® Type Softsynchro / PGR ® 2.6.1 Cleaning directions Clean the powRgrip interface of the collet holder, i.e. with a taper cleaner (see catalogue, chapter accessories) or with a clean towel. Degrease powRgrip collet, dip in a clean, fat-dissolving and oil-free solvent, i.e. -
Page 12: Length Adjustment
Operating instruction for collet holder ® type Softsynchro / PGR ® 2.6.2 Length adjustment Tool 1. Pick up collet holder 2. Set pre-adjustment tool in the collet holder Collet 3. Set collet into pre-adjustment tool 4. Set tool into collet Pre-adjustment tool 5. -
Page 13: Maintenance
Operating instruction for collet holder ® Type Softsynchro / PGR ® 3 Maintenance Maintenance schedule What? When? Who? External cleaning Periodically, depending on the degree Operator of dirt External cleaning Before clamping please make sure the collet holder is oil-free in the area of the ... - Page 14 Operating instruction for collet holder ® type Softsynchro / PGR ® Notes: Edition: 01.04.2012...
- Page 15 Operating instruction for collet holder ® Type Softsynchro / PGR ® Notes: Edition: 01.04.2012...
- Page 16 Softsynchro / PGR ® EMUGE-Werk Richard Glimpel GmbH & Co. KG · Fabrik für Präzisionswerkzeuge Nürnberger Straße 96-100 · 91207 Lauf · GERMANY · Tel. +49 (0) 9123 / 186-0 · Fax +49 (0) 9123 / 14313 info@emuge-franken.com · www.emuge-franken.com...
Need help?
Do you have a question about the Softsynchro 1/ PGR and is the answer not in the manual?
Questions and answers