Page 1: Table Of Contents
Jed T430/T440 Projector Controller user’s manual version V142F part B (Ed Schoell rev Sept 6 . 2018 … Flat panel only code version.) Table of Contents Active2Touch Panasonic LCD panels Sharp AHA/ Hitachi LCD Panasonic Plasma panels Mitsubishi with Sharp codes BenQ LCD, Clevertouch &...
Page 2: Aha/ Hitachi Lcd
After installation wiring of any projector to a T440, use a multimeter to check voltages of –9 on BOTH TX and RX pins in any installation, as described in the troubleshooting part of this manual. T440 User’s manual Flat panel part © JED Micro Pty Ltd Page 2...
Page 3 ** Note, the measured return voltage in rest state from the projector is only -0.9 volts, not the usual -5 to -9 volts. However the positive swing of voltage is OK. T440 User’s manual Flat panel part © JED Micro Pty Ltd Page 3...
Page 4 Input4 := '800s' + 22h +'001' + 0Dh; // Video2 HDMI 1 * (OPT1 swaps Video1 & Video 2) * T440: OPT6 switch ON will use S-Video in place of HDMI. T430: uses HDMI as Video2. Input4 := '801s' + 22h +'005' + 0Dh;...
Page 5 After installation wiring of any projector to a T440, use a multimeter to check voltages of –9 on BOTH TX and RX pins in any installation, as described in the troubleshooting part of this manual. T440 User’s manual Flat panel part © JED Micro Pty Ltd Page 5...
Page 6: Commbox Lcd Monitor
NO Panel connection blink codes and OPT7 handshake modes are available; • No mute/freeze commands are provided; and • Volume key presses send 5 consecutive Vol Up or Vol Down commands. • T440 User’s manual Flat panel part © JED Micro Pty Ltd Page 6...
Page 7: Hdi70 Lcd Panel
After installation wiring of any projector to a T460, use a multimeter to check voltages of –9 on BOTH TX and RX pins in any installation, as described in the troubleshooting part of this manual. T440 User’s manual Flat panel part © JED Micro Pty Ltd Page 7...
Page 8 RS232 mode) to IR (as needed for IR mode). T430: If using a T430, the keyboard has an ON/Source key and no Volume keys. The IR functions allow power On/Off and source change only. Operation is the same as above.
Page 9: Hitachi Lcd
After installation wiring of any projector to a T440, use a multimeter to check voltages of –9 on BOTH TX and RX pins in any installation, as described in the troubleshooting part of this manual. T440 User’s manual Flat panel part © JED Micro Pty Ltd Page 9...
Page 10: Lg Lcd/Plasma Tv
Use IR command PR- CH- * T440: OPT6 switch ON will use S-Video in place of HDMI. T430: uses HDMI as Video2.Any one of these codes can be set into Constant:0/Constant:1 for computer codes and Constant:2/Constant:3 for video codes. (The default is to have T440 User’s manual Flat panel part ©...
Page 11 'mc 00 01' + 0D Use IR command PR- CH- * T440: OPT6 switch ON will use S-Video in place of HDMI. T430: uses HDMI as Video2. Any one of these codes can be set into Constant:0/Constant:1 for computer codes and Constant:2/Constant:3 for video codes.
Page 12 'xb 00 A1’ + 0D 'xb 00 A1’ + 0D HDMI-2 / SDI / DTV Input16 'xb 00 B0’ + 0D 'xb 00 B0’ + 0D SuperSign T440 User’s manual Flat panel part © JED Micro Pty Ltd Page 12...
Page 13 Use IR command PR- CH- * T440: OPT6 switch ON will use AV2 Video in place of HDMI. T430: uses HDMI as Video2. Any one of these codes can be set into Constant:0/Constant:1 for computer codes and Constant:2/Constant:3 for video codes.
Page 14: Mitsubishi Lcd
Input4/Video2 '00_r1' + 0D HDMI * * OPT1 swaps Video1 &Video2 * T440: OPT6 switch ON will use S-Video in place of HDMI. T430: uses HDMI as Video2. S-Video code: '00_v3' + 0D Input5 '00_v2' + 0D Component 1 Video YPbPr (RCA)
Page 15 '00_v3' + 0D S-Video * T440: OPT6 switch ON will use S-Video in place of HDMI. T430: uses HDMI as Video2. Any one of these codes can be set into Constant:0/Constant:1 for computer codes and Constant:2/Constant:3 for video codes. (The default is to have Computer1 (above) as the “Computer” channel and Video1 as the “Video” channel.
Page 16 TV Channel Up '008B0001' TV Channel Down '008B0002' T440: OPT6 switch ON will use S-Video in place of HDMI. T430: uses HDMI as Video2. • On panel connection blink codes supported with new codes; • OPT7 handshake mode is available with new codes;...
Page 17 After installation wiring of any projector to a T440, use a multimeter to check voltages of –9 on BOTH TX and RX pins in any installation, as described in the troubleshooting part of this manual. T440 User’s manual Flat panel part © JED Micro Pty Ltd Page 17...
Page 18: Channel Codes Are
Input4 := 'kb 00 A' + 0D; // Video2 HDMI * (OPT1 swaps Video1 & Video2) * T440: OPT6 switch ON will use S-Video in place of HDMI. T430: uses HDMI as Video2. Input4 := 'kb 00 5' + 0D; //Video4 S-Vid * Input5 := 'kb 00 3' + 0D;...
Page 19 //Video2 RGB3 DVI-D ) * * (OPT1 swaps Video1 & Video2) * T440: OPT6 switch ON will use S-Video in place of HDMI. T430: uses HDMI as Video2. *Input4 := DF + 80 + 60 + 47 + 01 + 03 + 0A;...
Page 20: Input1 := 89 + 65 + 03 + 0E; Input2 := 89 + 65 + 09
Enable the RS-232 control access by going to “Setup” then to “Network Setup” then “Control I/F Select” and • set “RS-232”; Audio control 0->100 (Volume up/down keyboards, codes 2, 9, B, and E) is available; • Freeze is not supported at all; • T440 User’s manual Flat panel part © JED Micro Pty Ltd Page 20...
Page 21 Audio control (Volume up/down keyboards, codes 2, 9, B, and E) is available; • Freeze is not supported at all; • Male and female D9 connectors are used variously, and pin-out is shown in all manuals. T440 User’s manual Flat panel part © JED Micro Pty Ltd Page 21...
Page 22: Panasonic Plasma Panels
Yes, it’s confusing, but all we can offer at the moment. (The new T470 from JED will have re-label able keys, so will be able to have a correctly labelled set of keys for all the above. Stay tuned!) T440 User’s manual Flat panel part © JED Micro Pty Ltd Page 22...
Page 23: Plasma Lcd Tv (Ir)
:= 08 + 01 + AC + 09 + 00 + 01 + 00 + AD; //Video 2 HDMI 1 * (OPT1 swaps Video1 & Video2) * T440: OPT6 switch ON will use S-Video in place of HDMI. T430: uses HDMI as Video2. Input4 := 08 + 01 + AC + 01 + 01 + 01 + 00 + A4;...
Page 24: Philips Bdl Lcd/Led Panels
:= 09 + 01 + 00 + AC + 09 + 00 + 01 + 00 + AC; // Video 2 HDMI 1 (OPT1 swaps Video1 & Video2) * T440: OPT6 switch ON will use S-Video in place of HDMI. T430: uses HDMI as Video2.
Page 25: Pioneer Plasma Panels
:= 09 + 01 + 01 + AC + 0D + 0D + 01 + 00 + A4; //Video 2* HDMI 1 (OPT1 swaps Video1 & Video2) * T440: OPT6 switch ON will use S-Video in place of HDMI 1. T430: uses HDMI 1 as Video2.
Page 26 • Mute and freeze keyboard code 8 or A is not usable; • Aspect ratio control is not supported; and • TV mode is supported with a Code E keyboard, providing a TV button and Channel Up/Down keys. T440 User’s manual Flat panel part © JED Micro Pty Ltd Page 26...
Page 27 RS232 transmitter signal from TV RxD_RS232 RS232 receiver signal to TV IRout IR signal output from TV IR_CNTRL Switch cntl IRin and IRout signals IRin IR signal input to TV Ground T440 User’s manual Flat panel part © JED Micro Pty Ltd Page 27...
Page 28 After installation wiring of any projector to a T440, use a multimeter to check voltages of –9 on BOTH TX and RX pins in any installation, as described in the troubleshooting part of this manual. T440 User’s manual Flat panel part © JED Micro Pty Ltd Page 28...
Page 29: Promethean Activpanel Lcd
After installation wiring of any device to a T440, use a multimeter to check voltages of –9 on BOTH TX and RX pins in any installation, as described in the troubleshooting part of this manual. T440 User’s manual Flat panel part © JED Micro Pty Ltd Page 29...
Page 30: Samsung Plasma/Lcd Panels
Digital TV Some only TV Channel Up TV Channel Down * T440: OPT6 switch ON will use S-Video in place of HDMI. T430: uses HDMI as Video2. T440 User’s manual Flat panel part © JED Micro Pty Ltd Page 30...
Page 31 68 08 04 01 0D 82 HDMI 4 Input11 68 08 04 01 01 76 SCART Input12 68 08 04 01 00 75 ISP HBrowser/SINC as per Setting T440 User’s manual Flat panel part © JED Micro Pty Ltd Page 31...
Page 32 If a T430 is used with codes A5 or A7 then the switches on the back can be set to always select one of the sources, or allow toggling between two preset sources exactly the same as any RS232 controller panel or projector.
Page 33 • If a T430 is used, it needs to have the IR transmitter connection in place. A T440 Code 6 always has this installed. An IR transmitter bug or IR LED needs to be connected between the active line and ground.
Page 34: Sharp
'IAVD 7' + 0D Computer2 HDMI 3 Input3/Video1 Video1 'IAVD 1' + 0D Video1 Component / Video Input4/Video2 Video2 'IAVD 2' + 0D Video2 Component/S-Video / Video T440 User’s manual Flat panel part © JED Micro Pty Ltd Page 34...
Page 35 E0 … E3 with selections from the generic table above. In the back of each panel’s User’s Manual are allocations of ‘IAVD’ codes against physical inputs. T440 User’s manual Flat panel part © JED Micro Pty Ltd Page 35...
Page 36 'IAVD 1' + 0D Computer2 HDMI Input3/Video1 Video1 'IAVD 6' + 0D Video1 Component / Video Input4/Video2 Video2 'IAVD 4' + 0D Video2 Component / S-Video / Video T440 User’s manual Flat panel part © JED Micro Pty Ltd Page 36...
Page 37 Computer2 HDMI Input3/Video1 Video1 'IAVD 1' + 0D Video1 Component / Video Input4/Video2 Video2 'IAVD 3' + 0D Video2 Component / S-Video / Video / HDMI (some) T440 User’s manual Flat panel part © JED Micro Pty Ltd Page 37...
Page 38 E0 … E3 with selections from the generic table above. In the back of each panel’s User’s Manual are allocations of ‘IAVD’ codes against physical inputs. T440 User’s manual Flat panel part © JED Micro Pty Ltd Page 38...
Page 39 E0 … E3 with selections from the generic table above. In the back of each panel’s User’s Manual are allocations of ‘IAVD’ codes against physical inputs. T440 User’s manual Flat panel part © JED Micro Pty Ltd Page 39...
Page 40 E0 … E3 with selections from the generic table above. In the back of each panel’s User’s Manual are allocations of ‘IAVD’ codes against physical inputs. T440 User’s manual Flat panel part © JED Micro Pty Ltd Page 40...
Page 41 User’s Manual are allocations of ‘INPS’ codes against physical inputs. (Watch that you don’t try and use inputs which used shared sockets, eg DVI-D, BNC and HDMI.) T440 User’s manual Flat panel part © JED Micro Pty Ltd Page 41...
Page 42: Mitsubishi With Sharp Codes
After installation wiring of any projector to a T440, use a multimeter to check voltages of –9 on BOTH TX and RX pins in any installation, as described in the troubleshooting part of this manual. T440 User’s manual Flat panel part © JED Micro Pty Ltd Page 42...
Page 43 This shows the protocol and the connections and panels may need to have a software update to support RS232. This is covered by document: http://support.sharp.net.au/downloads/faqattach/PNx0Tx3_Monitor_Firmware_upgrade_guide.pdf Device manuals are: http://support.sharp.net.au/downloads/opmanuals/PN60TA3-PN70TA3_om.pdf http://support.sharp.net.au/downloads/opmanuals/PN70TB3-60TB3_manual_English.pdf http://support.sharp.net.au/downloads/opmanuals/PN80TC3_Operation_Manual.pdf T440 User’s manual Flat panel part © JED Micro Pty Ltd Page 43...
Page 44: Smart Lcd
Input4 := 'set input=HDMI1' + 0D; //Video 2 HDMI * (OPT1 swaps Video1 & Video2) * T440: OPT6 switch ON will use S-Video in place of HDMI. T430: uses HDMI as Video2. * Input4 := 'set input=S-Video' + 0D; // S-video V062...
Page 45: Soniq Lcd
No mute/freeze commands are provided; and • Volume key presses send 5 consecutive Vol Up or Vol Down commands. • T440 User’s manual Flat panel part © JED Micro Pty Ltd Page 45...
Page 46: Sony Lcd
//Option 2: RGB Group 1, Group 2, Group 3 Input19 := 8C + 00 + 01 + 02 + 13 + A2; //Option 2: Component Group 1, Group 2, Group 3 T440 User’s manual Flat panel part © JED Micro Pty Ltd Page 46...
Page 47 Input4 := xxx + 02 + 02 + CKS //Video 2 * * Setting T440: OPT6 switch ON will use S-Video in place of HDMI. T430: uses HDMI as Video2. Input5 := xxx + 02 + 03 + CKS // Video 3...
Page 48 Turn panel on manually; Turn T430/T440 on with ON button; Check commands all work, then turn OFF the system using the T430/T440 OFF button (this also sends the “Standby Command Enable”); Now turn on the panel with the T430/T440 ON button … it should now be fully remote-controllable via RS232.
Page 49 After installation wiring of any projector to a T440, use a multimeter to check voltages of –9 on BOTH TX and RX pins in any installation, as described in the troubleshooting part of this manual. T440 User’s manual Flat panel part © JED Micro Pty Ltd Page 49...
Page 50: 2-Touch/Ctouch
Input4 := 'kb 00 09' + 0D; // Video 2 HDMI 1 default * (OPT1 swaps Video1 & Video2) * T440: OPT6 switch ON will use S-Video in place of HDMI2. T430: uses HDMI2 as Video2. Input4 := 'kb 00 03' + 0D;...
Page 51: Viewsonic Lcd
Input4 := '801s"004'+ 0D; // Video 2 HDMI 1 default * (OPT1 swaps Video1 & Video2) * T440: OPT6 switch ON will use S-Video in place of HDMI2. T430: uses HDMI2 as Video2. Input4 := '801s"002'+ 0D; // Video 2 S-Video Input5 := '801s"003'+ 0D;...

This manual is also suitable for:

T440