Advertisement
Quick Links
Advertisement
Summary of Contents for Tasco TA515M Series
- Page 1 GEAR BENDER TA515M Series Instruction Manual...
-
Page 2: Table Of Contents
Thank you for purchasing this product. Read this Safety Notes and Instruction Manual thoroughly before using the product and ensure that instructions therein are fully understood. This manual summarizes “things that needs to be observed” so that the product can be used by everybody without any concern. -
Page 3: For Using The Product Safely
Safety Notes 1.For Using the Product Safely General instructions Do not modify the machine or use it for purposes other than those intended. WARNING [If neglected] The machine may fail or cause an accident, resulting in an injury of the operator. Wear clothing suitable for the task. - Page 4 Do not expose the machine to wind and rain. CAUTION [If neglected] It can be a cause of failure. Keep the workplace clean. CAUTION [If neglected] A workplace or a workbench that is littered can cause an accident. Do not use parts other than those designated by the supplier for replacement and other purposes.
-
Page 5: Part Name And Function
2.Part Name and Function 2.1 Features ■Need no power supply. ■Gears make labor-saving, easy and simple operation. ■Tripod with adjustable and foldable legs. ■Easy to carry and operate at work sites. 2.2 Parts ③ ① ② ⑥ ④ ⑤ ① Guide Pin ②... -
Page 6: Preparation
3.Preparation 1. Open up the tripod and turn left to loosen the legs. Pull out to a desired length and turn right to lock the legs. ※After setting the bender former on the tripod, adjust the length so that it’s horizontal. ※Do not pull the legs out beyond the yellow line for safety purposes. -
Page 7: Usage
2. Attach the bender former to the tripod with the fixing bolts. FIXING BOLT 4. Usage 1. Set the copper tube to the former and fasten the hook. Then put the guide pin through the former and the guide (arrow mark on the guide should be pointing upwards) completely. - Page 8 Move the ratchet handle forward and backward widely so that the former rotates. In order to apply the ratchet function, hold the socket of the ratchet wrench and move the handle forward and backward. Once there is resistance, replace the left hand on the guide pin as shown in the picture below.
- Page 9 WARNING Do not bend the copper tube other than the appropriate size. The machine is only for 1/2 hard copper tube. Do not bend a hard copper tube. Make sure to attach the guide pin. 【If neglected】 The machine may fail or cause an accident, resulting in an injury of the operator. CAUTION Make sure to support the copper tube during work.
-
Page 10: Primary Specification
5. Primary Specification FORMER I T E M N O . TA515M-7 TA515M-8 TA515M-9 TA515M-10 TA515M-12 APPLICABLE COPPER １／２ＨCOPPER TUBE M A T E R I A L 7/8” 1” 1-1/8” 1-1/4”※ 1-1/2”※ COPPER TUBE SIZE （22.23mm） （25.4mm） （28.58mm） （31.75mm） （38.1mm）... -
Page 11: Warranty Certificate
4) Failures due to consumable components. 5) Other failures not deemed to be the manufacturer’s responsibilities. GEAR BENDER Product Name: TA515M series Model: Date of purchase: M: Period of warranty: For 1 year starting from M: Customer Name:... - Page 12 1-17-20 Inadauemachi, Higashi-Osaka City, Osaka 577-0002, JAPAN Phone: 81-6-6748-9310 Fax: 81-6-6748-9320 Web Site: http://www.tascojapan.co.jp/...
Need help?
Do you have a question about the TA515M Series and is the answer not in the manual?
Questions and answers