Vehicle Weighing Solutions AIR WEIGHER M350S Quick Setup Manual

AIR WEIGHER
M350S Quick Setup Guide - two channel
Power-up the display by either switching on the ignition (ignition live
wiring) or press the power button beneath the logo (where fitted) if
the indicator is permanently wired to the vehicle supply.
to switch ON turn ignition
and/or press logo
Vehicle Weighing Solutions
Version 4D-01-16
Serial No:12B57664
M350S
For Service Tel:
0161 643 0202
Service due Jan 2010
M Display Configuration
E
Diagnostics Calibration
N
Alarms System
U
Options
ok
kg
1 2
print zero menu
kg
1 2
print tare menu
n n
e e
t t
kg
Channel 1 Channel 2
menu
Note
GROSS or GVW (gross vehicle weight) is the total truck weight (NET + TARE)
NET 'net load' means the payload weight in the truck body
LOAD means part load collected or delivered, press PRINT to print and zero the load, weight
collected is stored as an accumulation to NET
SPAN where used, means the NET weight used to calibrate the weigher
TARE weight means the weight of the empty vehicle
ALARM where fitted, an alarm sounder or flashing beacon will activate when alarm setpoint is reached
ON SITE when 'load' is turned on in options, on site allows logging onto site and
off site for weighing loads collected from a site with multiple bins (waste only)
TWIN means two channels are displayed and calibrated separately
DUAL means the indictor will split the weight readings between the channels
SALES
Vehicle Weighing Solutions
Unit 5, Southview Park, Marsack Street,
Caversham, READING RG4 5AF
T: 0118 946 1900
F: 0118 946 1862
Welcome screen
appears for 10 seconds
Service and calibration due screen
appears for 5 seconds
MENU
selectable options
net
NET
total load in body note, zero will appear
+/- 500 kg to mute alarm press any key
gross
GROSS
total truck weight note, zero will appear
+/- 500 kg
MENU
with options activated
kg
SPLIT SCREEN
Shows channel 1 front axle group
and channel 2 rear axle group
SERVICE
Vehicle Weighing Solutions (North)
United Business Centres Ltd.
4 Howarth Court, Gateway Crescent
Oldham Broadway Business Park
Oldham OL9 9XB
Tel. 0161 669 6193
M
A
B
MENU screen
MENU
Alarm graphic - shows both alarms.
A
Alarm set key
B
Print key - prints net, gross, time & date in weighing screens
C
Menu key - scrolls thru' NET, GROSS & MENU screens
D
Service reminder, flashes when weigher service is due
E
OK key - enters data
F
Down arrow key - scrolls down menu
G
Up arrow key - scrolls up menu
H
Back Up key - goes back a step
I
Display
Diagnostics
Alarms
Options
Configuration
Calibration
System
INSTALLATIONS
Vehicle Weighing Solutions
Unit 4a Sheepbridge Business Centre
Sheepbridge Lane, CHESTERFIELD S41 9RX
Tel: 01246 455 946
Fax: 01246 769 665
Firmware Version ???
E
C
D
M
Display Configuration
Diagnostics Calibration
E
Alarms System
N
Options
U
ok
F G H I
Changes OLED contrast to high, medium
or low. Also shows info: version & serial no.
Engineers screen. Shows two channel
weights and input milli-volt signals
Two alarm setpoints - PIN code required
To mute Alarm - press any key
Modes: Switches GROSS on & off
Load: On or off
RS232: Printer or scoreboard mode
Count by: 1, 10, 20, 50, 100, & 200 kgs
Z/Func: Allow/inhibit keyboard zero
To select 1 or 2 channels, air, oil or
fifth wheel.
Split: For split axle systems. Option for
total Ch1 + Ch2 or seperate Ch1 & Ch2
calibrations
Weighing system calibration settings
Accesses password set and resets.
Note. for PUK (PIN unlock code) contact
service who will take you through your
PIN retrieval. Edit time and date in system

need help

call service
?
0161 643 0202
info@vwsltd.co.uk
www.vwsltd.co.uk