Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for CD Automation Revo S 1PH
Summary of Contents for CD Automation Revo S 1PH
- Page 1 USER’S MANUAL Rev. 10/2018 Solid-State Relay From 30 to 40A M-RS1-30-40 CD Automation S.r.l. Via Picasso, 34/36 - 20025 Legnano (MI)- Italy Tel. +39 0331 577479 - Fax +39 0331 579479 E-mail: info@cdautomation.com - Web: www.cdautomation.com...
-
Page 3: Declaration Of Conformity
P.I. 08925720156 -Tel. +39 0331 577479 - Fax +39 0331 579479 E-mail: info@cdautomation.com - Web: www.cdautomation.com Declare that the product / Dichiara che il prodotto: Revo S 1PH 30-40A PRODUCT DESCRIPTION: Electric power control SCOPE OF APPLICATION: Thermal control process DESCRIZIONE DEL PRODOTTO: Unità... -
Page 4: Important Warnings For Safety
User’s manual REVO S 1PH from 30A to 40A Important warnings for safety This chapter contains important information for the safety. The not observance of these instructions may result in serious personal injury or death and can cause serious damages to the Thyristor unit and to the components system included. - Page 5 User’s manual REVO S 1PH from 30A to 40A WARNING! All service including inspection, installation, wiring, maintenance, troubleshooting, fuse or other user serviceable component replacement must be performed only by properly qualified personnel. Service personnel must read this manual before proceeding with work. While service is being performed un-qualified personnel should not work on the unit or be allowed in the immediate vicinity.
- Page 6 User’s manual REVO S 1PH from 30A to 40A AVERTISSEMENT! Au moment de relever des mesures de tension ou de courant en direct, utiliser un équipement de protection individuelle approprié pour les tensions et les potentiels d’arc électrique concernés. WARNING! Verify the voltage and current ratings of the power controller are correct for the application. AVERTISSEMENT! Vérifier que les valeurs de tension et de courant du régulateur de puissance sont correctes pour l’application.
-
Page 7: Maintenance
User’s manual REVO S 1PH from 30A to 40A Maintenance In order to have a corrected cooling, the user must clean the heat-sink and the protective grill of the fans. The frequency of this servicing depends on environmental pollution. Also check periodically if the screw for the power cables and safety earth are tightened correctly (See Connection Diagram) Warranty condition Producer gives a 12 months warranty to its products. -
Page 8: Table Of Contents
User’s manual REVO S 1PH from 30A to 40A Summary Declaration of conformity ......3 Important warnings for safety . -
Page 9: Basic Connections
User’s manual REVO S 1PH from 30A to 40A Basic Connections Single phase wiring with resistive load I= P V V = Nominal voltage of the load I = Nominal current of the load P = Nominal power of the load Open Delta wiring with resistive load I= P V = Nominal voltage of the load... -
Page 10: Order Code
User’s manual REVO S 1PH from 30A to 40A Order Code REVO S 1PH CURRENT FUSES & OPTION description code description code 0 3 0 No Fuse Fuse + Fuse Holder 0 4 0 Fuse + Fuse Holder + CT... -
Page 11: Technical Specifications
User’s manual REVO S 1PH from 30A to 40A tions General features Cover and Socket material: PolymericV2 Mounting: DIN bar (thickness type 1mm Max) Utilization Category: AC-51 AC-55b IP Code: Method of Connecting: Single Phase load Delay switch ON/OFF time: 1/2 Period Max Input features Logic input SSR:... -
Page 12: Environmental Installation Conditions
User’s manual REVO S 1PH from 30A to 40A Environmental installation conditions Ambient temperature 0-40 °C (32-104 °F) at nominal current. Over 40°C use the derating curve. Storage temperature -25°C to 70°C, -13°F to 158°F Installation place Don’t install at direct sun light, where there are conductive dust, corrosive gas, vibration or water and also in salty environmental. -
Page 13: Installation
User’s manual REVO S 1PH from 30A to 40A Installation Before to install, make sure that the Thyristor unit have not damages. ≥5 cm If the product has a fault, please contact the dealer from which you purchased the product. Verify that the product is the same thing as ordered. -
Page 14: Wiring Instructions
User’s manual REVO S 1PH from 30A to 40A Wiring instructions The Thyristor unit could be susceptible to interferences lost by near equipments or by the power supply, for this reason in accord to the fundamental practices rules is opportune take some precautions: •... -
Page 15: Connection Diagram For Single-Phase
User’s manual REVO S 1PH from 30A to 40A Connection Diagram for Single-phase L2/N L2/N LOAD Input: INPUT Note: 1 A suitable device must ensure that the unit can be electrically isolated from the supply, this allows the qualified people to work in safety. 2 The thyristor unit must be protected by extrarapid fuses (optional). -
Page 16: Firing Type
User’s manual REVO S 1PH from 30A to 40A Firing type Zero Crossing ZC firing mode is used with Logic Output from temperature controllers and the Thyristor operates like a contactor. The Cycle time is performed by temperature controller. ZC minimizes interferences because the Thyristor unit switches ON-OFF at zero voltage. -
Page 17: External Fuse (Not Included)
User’s manual REVO S 1PH from 30A to 40A External Fuse (not included) The thyristor unit without IFH option (Internal Fuse + Fuse-Holder), must be protected by fuses against short circuit. The Fuses must have I²t 20% less than thyristor’s I²t. The warranty of thyristor is null if no proper fuses are used. Fuse + Fuse-Holder Fuse Code Current... -
Page 18: External Fuse-Holder Dimension (Not Included)
User’s manual REVO S 1PH from 30A to 40A External Fuse-holder Dimension (not included) -
Page 19: Trouble Shooting
User’s manual REVO S 1PH from 30A to 40A Trouble shooting Small problems sometimes can be solved locally with the help of the below tab of trouble shooting. If you don’t succeed, contact us or your nearest distributor. Possible reasons Symptom Indication on front unit Actions... - Page 20 CD Automation S.r.l. Via Picasso, 34/36 - 20025 Legnano (MI)- Italy Tel. +39 0331 577479 - Fax +39 0331 579479 E-mail: info@cdautomation.com - Web: www.cdautomation.com...