Subscribe to Our Youtube Channel
Summary of Contents for Boston gear ORC-F Series Trig-O-Matic
- Page 1 Boston Gear ® ORC-F Series Trig-O-Matic Installation and Operation P-3002-BG ORC-F Series...
-
Page 2: Table Of Contents
The housing assembly includes a drive pawl and a position by the force of the return springs on the reset pawl which pivot within the clutch housing. return pins. Boston Gear • 800-825-6544 P-3002-BG... -
Page 3: Resetting Instructions
(Stamped 20) shown in Drive Spring Screw (Stamped 8) Drive Spring Figure 4, and turn the screw clockwise until the reset pawl releases the drive pawl. Refer Figure 4 to Table 5 for the proper wrench size. Boston Gear • 800-825-6544 P-3002-BG... -
Page 4: Type "T" Housing
1 Dowel Hole at 14° Sizes 1 and 2 Mounting Hole Pattern Sizes 3 and 4 Mounting Hole Pattern Sizes 5 and 6 Mounting Hole Pattern Figure 5 - Type “T” Standard Mounting Hole Patterns Boston Gear • 800-825-6544 P-3002-BG... -
Page 5: Type "B" Housing
These holes are not through holes and they should be avoided when mounting a coupling, sprocket, etc. to the clutch. "B" "C" "E" Dia. Typ. "G" "F" "A" Dia. "D" Figure 6 - Type “B” Housing Configuration Boston Gear • 800-825-6544 P-3002-BG... -
Page 6: Couplings To Shaft
2. If the clutch is a Model FJ or FG, loosen the clamp collar on the rotor of the clutch. If the clutch is a Model FR, remove the screw from the hole stamped 22 outside of the housing. Make Figure 10 Boston Gear • 800-825-6544 P-3002-BG... -
Page 7: Mounting Type "C" Flexible Coupling
4. Secure the coupling to drive shaft by tightening 1/2-13 620 in.lb the two setscrews located in the hub of the Table 8 - Coupling Setscrew Seating Torques flange. Refer to Table 8 for recommended coupling setscrew seating torques. Boston Gear • 800-825-6544 P-3002-BG... -
Page 8: R" Rigid Coupling
The shafts must be aligned until no gap exists or is equal at all points around the periphery. c. If a correction is required to satisfy angular alignment requirements, then recheck the parallel alignment. Feeler Gage Figure 12 Boston Gear • 800-825-6544 P-3002-BG... -
Page 9: Limit Switches
The clutch is also supplied with a grease relief fitting. When there is enough grease in the clutch any excess grease will be extruded through the relief fitting. Boston Gear • 800-825-6544 P-3002-BG... -
Page 10: Basic Unit Assembly
If the rotor is a Style 2, then press the out the reset spring (18), and the ball thrust (19) sawcut section of the rotor into the housing through the hole stamped 9. bearing. Boston Gear • 800-825-6544 P-3002-BG... -
Page 11: Torque Verification
1. Place the clutch in a chuck or vise with the cover facing upward. 2. Insert the appropriate size arbor and key into rotor. (See Figure 16) Drive Screw Flush Figure 15 - Clutch Internal Components Boston Gear • 800-825-6544 P-3002-BG... -
Page 12: Final Assembly
(20) until the desired release torque is obtained. 8. Once the desired release torque is obtained, tighten the locking screws (24) located over the drive spring and reset spring screws to ensure that they will not move. Boston Gear • 800-825-6544 P-3002-BG... -
Page 13: Vll. Trouble Shooting
Non-Coupled Units) Unit Bore Model Bored to Size (in 1/16”) FJ- Model F, M- Metric Bored to Size (mm) Full Available Shaft Length FG- Model F, Limited Available Shaft Length FR- Model F, Overall Limited Space Boston Gear • 800-825-6544 P-3002-BG... -
Page 14: Exploded View Drawing
ORC Series, Model F Boston Gear • 800-825-6544 P-3002-BG... -
Page 15: Catalog Numbers
710356-004 710356-005 Dependent upon bore - include bore size and complete clutch part number. ** -001 Automatic; -003 Manual *** -001 Automatic; -002 Manual Note: Please include clutch catalog number when ordering any spare parts. Boston Gear • 800-825-6544 P-3002-BG... - Page 16 No employee, agent, distributor, or other person is authorized to give additional warranties on behalf of Boston Gear, nor to assume for Boston Gear any other liability in connection with any of its products, except an officer of Boston Gear by a signed writing.
Need help?
Do you have a question about the ORC-F Series Trig-O-Matic and is the answer not in the manual?
Questions and answers