Roland OP-R26CW Owner's Manual

Cover/Windscreen Set for R-26
OP-R26CW
Owner's manual
Before using this product, carefully read the sections entitled: "USING THE UNIT SAFELY" and "IMPORTANT NOTES". These sections
provide important information concerning the proper operation of the product. Additionally, in order to feel assured that you have
gained a good grasp of every feature provided by your new product, Owner's manual should be read in its entirety.
The manual should be saved and kept on hand as a convenient reference.

Work Cover/Strap

Insert the R-26 into the work cover, in the
direction shown in the illustration.
• To ensure that the R-26 doesn't get scratched when you insert it inside this product, carefully check to make sure that
no dirt, dust, or other foreign matter is stuck to the surface of the R-26 or on the inside of the cover.
• When using the work cover, always make sure that you also have the strap attached.
After the work cover has been put on the
R-26, pass the strap from above through the
slot on the R-26.
• Attach the strap securely so that it does not easily become detached. If the strap is loose, when carrying the R-26, it
could be dropped, possibly resulting in damage or injury.
• Use only the provided strap. The included strap is meant for exclusive use with the R-26. Do not use this strap for other
products.
• Check to make sure that the strap is securely fastened.
• In households with children, be careful with the parts that are used to adjust the strap, so as to prevent accidental
ingestion.
• Do not spin or swing the R-26 while holding it by the strap. This is extremely dangerous, as it may cause the strap to
become detached; or may even break the strap.
Copyright © 2011 Roland CORPORATION
All rights reserved. No part of this publication may be reproduced in any form without the written permission of Roland
CORPORATION.
Roland is a registered trademark of Roland Corporation in the United States and/or other countries.
※ 日本語は裏面に掲載しています。
As shown in the illustration, attach the
strap securely, so it won't come loose.

Travel Cover

With the work cover still in place, insert the
microphone section of the R-26 to the travel
cover.

Windscreen

Align the cloth portion on the inside of the
windscreen with the hook and loop fastener
on the work cover.
Hook and loop
fastener
Notches
• Please note that some of the acrylic fur of the windscreen may fall out. Also note that it is not water repellent.

USING THE UNIT SAFELY

Maintenance

• For everyday cleaning wipe the
• Do not drop the R-26 or subject it to
strong impact while it is in this product. product with a soft, dry cloth or one
that has been slightly dampened with
Also, be careful not to drop the unit
when removing it from this product. water. To remove stubborn dirt, use a
cloth impregnated with a mild, non-
abrasive detergent. Afterwards, be sure

IMPORTANT NOTES

to wipe the product thoroughly with a
soft, dry cloth.
• Do not expose the product to direct
sunlight, place it near devices that
• Never use benzine, thinners, alcohol
radiate heat, leave it inside an enclosed
or solvents of any kind, to avoid the
vehicle, or otherwise subject it to possibility of discoloration and/or
temperature extremes. Excessive heat
deformation.
can deform or discolor the product.
This product contains chemicals known to cause cancer, birth defects and other reproductive harm, including lead.
Fasten the snap fasteners on the rear (three
places).
Attach the windscreen, while making sure
that the elastic is held by the notches in the
work cover (four places).

Main Material

Polyurethane cloth
(Front cloth)
Cover
Polyester (Inner cloth)
Windscreen Acrylic
Strap Polypropylene tape
* In the interest of product improve-
ment, the speci cations and/or
appearance of this product are subject
to change without prior notice.
For C.A. US (Proposition 65)
WARNING