Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for FSP Technology K948
- Page 1 User Manual Version 1.0 August 2013 Bedside Terminal Hardware System...
- Page 2 Copyright 2013 All Rights Reserved Manual Version 1.0 The information contained in this document is subject to change without notice. We make no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose.
- Page 3 CE MARK This device complies with the requirements of the EEC directive 2004/108/EC with regard to “Electromagnetic compatibility” and 2006/95/EC “Low Voltage Directive” This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference.
- Page 4 Safety Caution Note: To comply with IEC60950-1 Clause 2.5 (limited power sources, L.P.S) related legislation, peripherals shall be 4.7.3.2 "Materials for fire enclosure" compliant. 4.7.3.2 Materials for fire enclosures For MOVABLE EQUIPMENT having a total mass not exceeding 18kg.the material of a FIRE ENCLOSURE, in the thinnest significant wall thickness used, shall be of V-1 CLASS MATERIAL or shall pass the test of Clause A.2.
- Page 5 be readily identifiable and easily reached by the operator. For single-phase portable equipment, a plug on a cord of length not greater than 3m is considered to be easily reached. LEGISLATION AND WEEE SYMBOL 2012/19/EU Waste Electrical and Electronic Equipment Directive on the treatment, collection, recycling and disposal of electric and electronic devices and their components.
- Page 6 Revision History Revision Date Description V1.0 August, 2013 Release...
-
Page 7: Table Of Contents
Table of Contents 1 Intended Use ............1 2 Package Checklist ..........2 Standard Items ................. 2 3 System View ............3 Front View ..................3 Side View.................... 4 Rear View ................... 4 Bottom View ..................5 Dimension ..................5 4 System Assembly .......... -
Page 8: Intended Use
Intended Use According to the Instructions for Use (IFU) of the manufacturer, the Bedside Terminal has the following intended use: The Bedside Terminal Hardware System is a computing device capable of storing, retrieving and sending data electronically. This Bedside Terminal Hardware System, including its user interface, battery, PCB and power supply, is intended to be fixed to a stand in medical care environment. -
Page 9: Package Checklist
Package Checklist Standard Items a. System b. Phone module c. Power adapter d. Power Cable e. Manual f. Stand... -
Page 10: System View
System View Front View Number Description Build-in camera Camera LED Touch screen Touch keys (from left to right: reading light, volume down, volume up, channel down, channel up , power button) Smart IC card reader VOIP phone (optional) -
Page 11: Side View
Side View Number Description Combo smart IC card reader with separate RFID antenna (optional) Speaker Rear View Number Description Light Sensor Webcam switch Ventilation SSD/HDD door Cable cover Vertical I/O port (from left to right: Nurse call, Display port, DC jack, USBx2, LAN ) -
Page 12: Bottom View
Bottom View Number Description Ventilation From left to right: Video in, Audio left, Audio right (optional) Bottom I/O port (from let to right: LAN, USBx2, Remote, Power button) Microphone Smart IC card reader USBx1 Phone jack (RJ11) From left to right: Audio line-out, Mic-in, Audio line-out Dimension... -
Page 13: System Assembly
System Assembly SSD/HDD Replacement 1. Remove the screw (x1) to open the HDD door. 2. Remove the screw (x1) that fixed the HDD to the system. 3. Pull the HDD outward as shown in the picture. 4. The HDD is secured by a metal bracket, remove the screws (x2) to release the metal bracket from the HDD. -
Page 14: Peripherals Installation
Peripherals Installation Phone module Installation Loosen the screw(x1) to open the cable cover. Slide the phone module into the phone holder and connect the other end of the phone cable to the connector on the system. -
Page 15: Stand Installation
Stand Installation Fasten the screws.(monitor screw M6x10 4pcs) -
Page 16: Specification
Specification Model K948 Motherboard Processor Intel Celeron 1047UE Core Logic CPU with Graphic built-in HM76 System Memory 2 x DDR3 SO-DIMM slot up to 8GB FSB1600Mhz Graphic Memory DX11, HD Graphic 350MHz LAN Controller / PHY Intel WG82583V / Intel WG82579V... - Page 17 Model K948 Motherboard Mic-In 1 (Auto-detect,GPIO), in external IO Vertical I / O 1 x RJ45 (with 10/100/1000) Power DC Jack 1 x DVI-D Display Port 1 x DVI-D 2 (USB 2 .0) Nurse Call 1 x RJ48 Touch Keys...
- Page 18 Address: NO.36 Huaya 3rd Rd., Guishan Township, Taoyuan County 33383, Taiwan Tel No: 886-3-272-9688 Fax No: 886-3-272-9666 Note: Cleaning solution-Wipe with cloth using clean water, 2 times a week. Adaptor Manufacturer: FSP TECHNOLOGY INC. 1. Model: PMP105-18-B15 Rating: 100-240V,47-63Hz,0.7 – 1.4A Model: PMP60-12-B16...
-
Page 19: Jumper Setting
Jumper Setting C73 Motherboard... -
Page 20: Connectors & Functions
Connectors & Functions Connector Function Scanner Nurse Call LED Power Build-In MIC Inverter COM5 (for touch) USB port for Web Cam HDD LED SATA Power CN10 SATA Power CN11 PS/2 keyboard CN12 LVDS CN14 COM1 CN16 CN17 Power LED CN18 CN19 CN20 IrDA... -
Page 21: Jumper Setting
Jumper Setting Brightness Type Selection Function (1-2) (3-4) (5-6) ▲LED Power Mode Setting Function (1-2) ▲ATX Power AT Power LCD ID Setting Function (1-2) (3-4) (5-6) (7-8) 18.5” AUO LCD ▲ = Manufacturer Default Setting OPEN SHORT...