Radio Shack 3201258 User Manual

3201258
Package contents
User's Guide
• Microphone • Receiver
• 9V AC Adapter • User's Guide
• Quick Start
170MHz VHF Single-Channel
Wireless Microphone System
Features
• Includes wireless microphone and receiver.
• Built-in compander for noise reduction.
• Up to 200 feet range.
1 Install batteries
Unscrew the microphone grille and remove
the battery cover. Insert two AA batteries with
correct polarities. Then replace the battery
cover and the microphone grille.
b
Battery Notes:
• Dispose of old batteries promptly
and properly. Do not burn or bury
batteries.
• Use only fresh batteries of the required
size and recommended type. Do not
mix batteries of different sizes or types.
• If you do not plan to use your
microphone system for a month or more, remove the
batteries. Batteries can leak chemicals that can damage
electronic parts.
Thank you for purchasing your Wireless Microphone System
from RadioShack. Please read this user's guide before installing,
setting up, and using your new microphone.
2
3201258_PM_EN.indd 1-8
2
Connect the system
READY
Indicator lights when
microphone signals
are within range of
VOLUME
the receiver.
Rotate to
adjust your
POWER
microphone's
Indicator lights volume.
n
when power is on.
Note: You can simultaneously connect both output jacks to
an amplifier and another device.
3 Power and use the system
1
1. Press POWER on the receiver to turn it on. The POWER
indicator lights.
2
2. Fully extend the receiver's antennae.
POWER SQUELCH
3 3. Set the volume on your PA amplifier or other audio source
Turn the receiver
Rotate to limit background noise and
to a low level.
on/off. control transmitting distance. To increase
the transmitting distance, rotate to MIN. 4 Turn power on.
1. Set the volume to minimum level and plug in the AC 5. Set TALK-MUTE-OFF switch to TALK.
adapter.
Using a shielded audio cable (not included), connect the
2.
LINE output jack on your receiver to the input jack on your
amplifier, or other device.
3. Or, if the LINE jack is in use, you can connect using the
MICROPHONE output jack on your receiver and to the
input jack on your amplifier with a ¼" audio cable (not
included).
Turn the amplifier or other audio source and receiver
6.
volume up to the desired level. The READY indicator lights
3
indicating that the microphone signals are within range of
Connections – Back View
the receiver.
n
Notes:
• To avoid a popping noise that may occur when switching
from OFF to TALK, use MUTE.
MICROPHONE Connect
LINE
• When you finish using the system, turn TALK-MUTE-OFF to
(Optional) the 9V AC
Connect to the
OFF.
Connect to an adapter.
input jack on
amplifier. The frequency version of your system is preset. When
an amplifier or •
other device. two sets at same operating frequency work close to each
other, they have mutual interference. In order to minimize
interference, three different operating frequencies are
provided. When using wireless microphones simultaneously,
make sure your system's frequency versions are different.
Check the frequency label on the bottom of the receiver
and inside the microphone's battery compartment.
Specifications
Three options for frequency:
.................................:169.505 MHz, 170.245 MHz, or 171.905 MHz
Operating range .......................................................200 ft (Typical)
Frequency response ................................................... 120-13000Hz
Microphone
RF Power................................................................................10dBm
The LED lights Sensitivity . ....................................................106dB SPL at 7kHz FM
when TALK- Power source . ....................................................... two AA batteries
MUTE-OFF is set
Dimensions (Diam. × H) 2.2 × 9.8 in . .......................(55 × 110 mm)
.
to TALK or MUTE
Receiver
Sensitivity with S/N 20dB .......................................................... 1uV
Slide to TALK
to use the
S/N ratio at 1mV RF Input .......................................................75dB
microphone.
Image rejection . .......................................................................55dB
Line output ............................................................................ 510mV
Microphone output ................................................................ 10mV
4 5
Power requirement ....................................................... AC adapter antenna or the device could result in the system exceeding the RF exposure
requirements.
Dimensions (WHD) 8.9 × 2.2 × 4.3 in ............. (225 × 55 × 11 mm)
For devices less than 200mW ERP
Specifications are subject to change and improvement without notice. Actual
SAFETY INFORMATION
product may vary from the images found in this document.
Your wireless microphone contains a low power transmitter. When the EUT is
powered on, it sends out radio frequency (RF) signals. In August 1996, the Federal
FCC Information
Communications Commissions (FCC) adopted RF exposure guidelines with safety
levels for wireless devices.
WARNING: Modifying, tampering with, or adjusting this unit, or replacing any
IMPORTANT
transmitter component (crystal, semiconductor, etc.) may result in a violation of the
FCC rules. To maintain compliance with the FCC's RF exposure guidelines, hold the transmitter
and antenna at least 1 inch (2.5 centimetres) from your face and speak in a normal
NOTE: This equipment has been tested and found to comply with the limits
voice, with the antenna pointed up and away from the face. Ensure that the antenna
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
is at least 1 inch (2.5 centimetres) from your body when you are using your wireless
are designed to provide reasonable protection against harmful interference in
microphone.
a residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, Use only the supplied antenna. Unauthorized antennas, modifications, or attach-
may cause harmful interference to radio communications. However, there is no ments could damage the transmitter and may violate FCC regulations.
guarantee that interference will not occur in a particular installation. If this equip-
ment does cause harmful interference to radio or television reception, which can be
Limited Warranty
determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
RadioShack warrants this product against defects in materials and workmanship
• Reorient or relocate the receiving antenna.
under normal use by the original purchaser for one (1) year after the date of
• Increase the separation between the equipment and receiver.
purchase from a RadioShack-owned store or an authorized RadioShack franchisee
• Connect the equipment into an outlet on a circuit different from that to which the
or dealer. RADIOSHACK MAKES NO OTHER EXPRESS WARRANTIES.
receiver is connected.
This warranty does not cover: (a) damage or failure caused by or attributable to
• Consult your local RadioShack store or an experienced radio/TV technician for
abuse, misuse, failure to follow instructions, improper installation or maintenance,
help.
alteration, accident, Acts of God (such as floods or lightning), or excess voltage
If you cannot eliminate the interference, the FCC requires that you stop using
or current; (b) improper or incorrectly performed repairs by persons who are not a
your microphone system. Changes or modifications not expressly approved by
RadioShack Authorized Service Facility; (c) consumables such as fuses or batteries;
RadioShack may cause interference and void the user's authority to operate the
(d) ordinary wear and tear or cosmetic damage; (e) transportation, shipping or
equipment.
insurance costs; (f) costs of product removal, installation, set-up service, adjustment
Shielded cables must be used with this unit to ensure compliance with the Class B or reinstallation; and (g) claims by persons other than the original purchaser.
FCC limits.
Should a problem occur that is covered by this warranty, take the product and the
This device complies with Part 15 of the FCC Rules. Operation is subject to the
RadioShack sales receipt as proof of purchase date to any RadioShack store in
condition that this device may not cause harmful interference. the U.S. RadioShack will, at its option, unless otherwise provided by law: (a) repair
This wireless microphone system complies with Part 90 of the FCC Rules. There the product without charge for parts and labor; (b) replace the product with the
are three frequencies available for the system. You must obtain a license for each
same or a comparable product; or (c) refund the purchase price. All replaced parts
frequency you plan to use before operating your system. One license can include
and products, and products on which a refund is made, become the property of
both frequencies. Visit http://wireless.fcc.gov/uls/, or call your local FCC office to
RadioShack. New or reconditioned parts and products may be used in the perfor-
apply for your license. Your ability to obtain a license will depend on how you plan mance of warranty service. Repaired or replaced parts and products are warranted
to use the system. for the remainder of the original warranty period. You will be charged for repair or
For RF exposure replacement of the product made after the expiration of the warranty period.
IMPORTANT NOTE: To comply with the FCC RF exposure compliance require- To comply with the FCC RF exposure compliance require- RADIOSHACK EXPRESSLY DISCLAIMS ALL WARRANTIES AND CONDITIONS
ments, no change to the antenna or the device is permitted. Any change to the NOT STATED IN THIS LIMITED WARRANTY. ANY IMPLIED WARRANTIES THAT
MAY BE IMPOSED BY LAW, INCLUDING THE IMPLIED WARRANTY OF MER-
6 7
CHANTABILITY AND, IF APPLICABLE, THE IMPLIED WARRANTY OF FITNESS FOR
A PARTICULAR PURPOSE, SHALL EXPIRE ON THE EXPIRATION OF THE STATED
WARRANTY PERIOD.
EXCEPT AS DESCRIBED ABOVE, RADIOSHACK SHALL HAVE NO LIABILITY
OR RESPONSIBILITY TO THE PURCHASER OF THE PRODUCT OR ANY OTHER
PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS OR DAMAGE
CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFORMANCE OF THE
PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, INCLUDING,
BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE
AND ANY LOSS OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT AND ANY
INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF
RADIOSHACK HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Some states do not allow limitations on how long an implied warranty lasts or
the exclusion or limitation of incidental or consequential damages, so the above
limitations or exclusions may not apply to you. This warranty gives you specific legal
rights, and you may also have other rights which vary from state to state. You may
contact RadioShack at: RadioShack Customer Relations
300 RadioShack Circle, Fort Worth, TX 76102 04/08
www.RadioShack.com
Protect the environment by recyling used electronics. Go to
E-CyclingCentral.com to find an electronic recycling center near
you.
©2011. RadioShack Corporation.
All rights reserved. RadioShack and www.RadioShack.com Printed 04B11
are trademarks used by RadioShack Corporation. in China 3201258
8
4/20/2011 10:29:32 AM