Arlec LVG550 Installation Instructions

TROUBLE SHOOTING AND USER HINTS

Problem Possible Causes
Lights do not operate. No power.
Blown fuse.
Low voltage cable has not been connected to
transformer
Lights do not switch on at dusk when using either Artificial light affecting Timer/Light Sensor (ie,
the "Dusk Till Dawn" or "Timer" mode. (Daylight street lights, car lights, etc).
Sensor/Timer transformers only, or when using
separate Time/Light Sensor,).
Timer/Light Sensor
Only some of the lights switch on. Connecting pins in cable connector have not
penetrated into cable.
Light stays on for longer period than the timer If the Timer/Light Sensor detects a light source
suggests. Daylight Sensor/Timer transformers only, (porch light, car light etc) during the time in which
or when using separate Time/Light Sensor. the garden lights are on, the transformer will switch
the garden lights off and then re-start the pre-
programmed time again when the light has passed.

Arlec Warranty

Arlec guarantees this product against defects
of materials and workmanship for a period of
12 months from the date of purchase provided the
product is used for its proper purpose, in accordance
with Arlec's recommendations and within such
voltage and current limits as are specified by Arlec in
relation to the product. Arlec will at its own option
and cost make good, or replace this product with
the same or similar product and return it to you, or
provide a credit for any product manufactured or
supplied by it, which proves to be defective within
the limits set out above provided that no repairs,
alterations or modifications to the product have
been undertaken or attempted by anyone, other
than Arlec or its authorized agents. Should you wish
to make a claim under this guarantee, the product
and proof of purchase must be returned pre-paid by
you to the place of purchase.
This guarantee is in addition to and does not take
away from any other rights and remedies you may
have under any relevant law.
Our goods come with guarantees that cannot be
excluded under the Australian Consumer Law.
You are entitled to a replacement or refund for a
major failure and for compensation for any other
reasonably foreseeable loss or damage.
LVG550_CPIN1048-4.indd 1-2
Possible Solutions
Ensure transformer is plugged in and power is on.
(Is the power point working?)
Replace fuse. (Note: some transformers may not be
fitted with fuse).
Ensure the low voltage cable is connected to the
transformer. (Is the connection firm?)
Mount Timer/Light Sensor in a position where
artificial lights do not affect its operation. To check
light sensor: ensure switch is in either "Dusk Till
Dawn" or "Timer Hour" position, cover sensor lens
with black PVC tape (ensuring that no light gets
in). The lights should switch on after a few seconds.
If the lights have now switched on, the light sensor
may simply require mounting in a position where
artificial light cannot affect its operation.
Straighten pins with pliers then reconnect.
Mount Timer/Light Sensor in a position where
artificial light cannot affect its operation.
You are also entitled to have the goods repaired or
replaced if the goods fail to be of acceptable quality
and the failure does not amount to a major failure.
Proof of Purchase
Please retain your proof of purchase for all warranty
claims.
For all Sales & Warranty enquiries
Arlec Australia Pty Ltd. (A.C.N. 009 322 105)
Building 3, 31- 41 Joseph Street,
Blackburn North, Victoria, 3130
P .O. Box 1065, Blackburn North LPO
Blackburn North, 3130
Phone (03) 9982 5111; Fax 1300 360 650
custservice@arlec.com.au
© This instruction leaflet is subject to copyright and
must not be reproduced, copied or otherwise used
in any way or for any purpose without the consent in
writing of the owner,
Arlec Australia Pty Ltd (A.C.N. 009 322 105).
CPIN1048/4
Garden Light
LED Spot
Installation Instructions
Keep these instructions in a safe place for future reference
CPIN1048/4
LVG550
19/07/11 5:38 PM