Advertisement
Quick Links
CSM-BC500 QUICK SETUP GUIDE
MONITOR SETUP
Open the battery compartment:
1
1. Install three "AAA" Batteries
2. Close cover and secure screw
Optional: connect an AC adaptor to
extend battery life.
SYNCHRONIZING ONE CORDLESS SENSOR OR A SECOND
CORDLESS SENSOR
Press and hold the black programming button located on the bottom of the monitor
1
for approximately three seconds. Both the yellow and green LEDs will then light for
15 seconds.
1
TEST THE ALARM:
3
1. When pressure is placed back on the pad, the green LED will blink two times and then continuously every three seconds indicating the pad is in use.
2. Remove pressure from the pad to activate the alarm. The red LED will then blink (for 10 seconds) and nurse call will alarm.
3. To cancel the alarm, press the monitor's RESET button and cancel the nurse call alarm at the patient station.
UNSYNCHRONIZING A CORDLESS SENSOR
Remove pressure from pad(s).
1
NOTE: If a pad is in use (pressure applied), it will remain synchronized and
monitoring the patient, even after attempting to unsynchronize.
1
TEST THE ALARM:
3
1. When pressure is placed back on the pad, the green LED will blink two times and then continuously every three seconds indicating the pad is in use.
2. Remove pressure from the pad to activate the alarm. The red LED will then blink (for 10 seconds) and nurse call will alarm.
3. To cancel the alarm, press the monitor's RESET button and cancel the nurse call alarm at the patient station.
Turn the CALL CORD switch to OFF before initially
2
inserting the nurse call plug or cable into the patient
station. If using with the call cord, switch to ON after
connected to the patient station and inserting the
call cord.
(MAKE SURE THE TRANSMITTER IS SETUP PRIOR TO SYNCHRONIZING)
2
3
2
3
NOTE: Consult the "Directions For Use" included with monitor for
complete instructions, troubleshooting, and safety information
Within 10 seconds of pressing the programming button, place pressure on the
2
sensor pad and then release. The yellow LED will blink once, confirming the
monitor and pad are now synchronized and ready for use.
Press and hold the PROGRAM button first, then press and hold the RESET
2
button at the same time, for two seconds. The yellow and green LEDs will
simultaneously flash three times indicating that the pad(s) has
been unsynchronized.
www.curbellmedical.com • 1-888-222-2188
©2017 Curbell Medical Products, Inc.
MAP1679B
Advertisement
Summary of Contents for Curbell CSM-BC500
- Page 1 CSM-BC500 QUICK SETUP GUIDE NOTE: Consult the “Directions For Use” included with monitor for complete instructions, troubleshooting, and safety information MONITOR SETUP Open the battery compartment: Turn the CALL CORD switch to OFF before initially inserting the nurse call plug or cable into the patient 1.
- Page 2 CORDED SENSOR USE CORDED PAD CONNECTION: TEST THE ALARM: 1. Plug the sensor cord into the monitor’s sensor jack. 1. When pressure is placed back on the pad, the green LED will blink two times 2. Both LEDs flash 3 times simultaneously. and then continuously every three seconds indicating the pad is in use.
- Page 3 This checklist has been developed to help identify common issues that can be quickly addressed to prevent unnecessary product returns. Please also refer to the product’s Directions for Use and instructional video on Curbell’s website (www. curbellmedical.com). If, after completing the checklist, the product continues to malfunction, please call your Curbell Representative at 888-222-2188.
- Page 4 No alert is given to the facility’s nurse call system The monitor and/or the 1/4" mono nurse call jack is securely connected to the nurse call patient station and is not damaged. False alarm or no alarm sound occurs The pad is placed properly on the chair or bed. figure 4 No part of the pad/mat (including the neck of the pad) is folded and/or creased.
Need help?
Do you have a question about the CSM-BC500 and is the answer not in the manual?
Questions and answers