Advertisement
声明
1.请阅读这些说明;
2.请注意所有警告;
3.请遵循所有说明;
4.切勿在散热器、 电热器、 炉子、 或其它产热设备等热源附近进行工作;
5.仅使用制造商为QooCam指定和提供的附件与配件;
6.请将所有维修工作交由符合资质的人员处理。 不论设备受到何种形式的损坏， 例如电源线或插头损坏， 液体渐入或物体落入此设备淋
雨或受潮， 无法正常工作或坠落， 均需进行维修。
摄像机的安全
警告： 如果你未能采取下列预防措施， 则可能会因电击或火灾造成严重伤害或死亡， 或者造成你的QooCam受损， 使用摄像机和配件前
请进行检查， 确保其完好无损。 处于安全原因， QooCam只能使用随附的或另行购买的正品QooCam配件。 如使用并非由Kandao推荐
的任何其它部件、 配件或充电器， 可能导致火灾、 触电或人身伤亡。 因使用未授权的附件而造成的损坏不属于担保范围。 要了解获得批准
的配件， 请访问Kandao官网www.kandaovr.com
1.摄像机充电时， 切勿用湿手碰触插头或充电器。 如果您不遵守本警告信息， 则可能发生触电。
2.切勿将本产品置于或固定在不稳定的表面上。 不遵守此预防措施可能会导致产品松开或者脱落， 从而引发事故或损坏相机。
3.如果使用外部电源连接， 请遵守第三方供电设备的所有安全准则。
4.QooCam摄像机镜头采用玻璃制成。 如果镜头破坏， 请务必小心处理， 避免被破碎的玻璃划伤， 切勿让儿童接触。
5.摄像机在运行时温度可能会升高， 这是使用过程的正常现象。 在这种情况下， 关闭相机， 将摄像机静放至冷却后再尝试使用。
6.本产品并非玩具， 您应全权负责遵守当地的所有法律、 法规和限制。
7.请勿将QooCam用于未经授权的监控、 偷拍或以侵犯个人隐私法规的任何方式使用。 通常情况下， 严禁将摄像机用于此类用途， 并且可
能会致使操作者承担重大责任和面临刑事诉讼。
8.注意事项： 请勿将摄像机置于极冷或极热的环境中， 极冷或极热条件可能会缩短电池的使用时间， 或者导致相机暂时不能正常工作。
9.警告： QooCam的3个镜头没有任何保护， 如果不注意则很容易形成划痕。 始终将QooCam存放在随附的镜头保护盖中， 避免将镜头放
置在任何表面上， 镜头划痕不在保修范围内。
该符号表示， 根据当地法律法规， 您的产品应和家庭垃圾分开处理。 当产品寿命终止时， 请将其带到地方当局指定的回收点。 弃置产
品时对其进行分开收集与回收有助于保护自然资源， 并确保以有益人体健康和保护环境的方式进行回收。
Kandao. Inc. hereby declares that QooCam of wireless device type complies with Directive 2014/53/EU.
Product Name: QooCam 360&3D Camera, Product Model: QCM0106
Software Version:HW_2-SW_VER_31-ISP_0509H, HW Version:KIB_3_S317_MB_V2.0
QooCam transmits data in the frequency band 2.412-2.472GHz, or 5.15-5.25GHz . Particular laws and regulations of some countries may prohibit
or restrict the use of partial or all frequency bands listed above. The maximum output power is 16 dBm.
Hereby, Kandao lightforge Co.,Ltd. declares that the radio equipment type QCM0106 is in compliance with Directive 2014/53/EU.The full text of the
EU declaration of conformity is available at the following internet address: https://www.kandaovr.com/en/qoocam/ce-marking.
Importers: Italy
ADCOM s.r.l. Kandao VR camera reselling and after-sale service center in Italy. via Zanardi, 50 - 40131 Bologna
+39 051 36 99 40
www.adcom.it
info@adcom.it
FCC ID : 2AMZV-KDQC
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating
instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
The portable device is designed to meet the requirements for exposure to radio waves established by the Federal Communications Commission
(USA). These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard
during product certification for use when properly worn on the body(the test distance of SAR is 0mm)
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
CN
Advertisement
