Ventrac ED202 Operator's Manual And Parts List
  1. Manuals
  2. Brands
  3. Ventrac Manuals
  4. Edger
  5. ED202
  6. Operator's manual and parts list

Ventrac ED202 Operator's Manual And Parts List

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Operator's Manual
& Parts Drawings
Edger
Model ED202
Revised 10/26/18
Original Operator's Manual
09.10142 Rev. 02

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ED202 and is the answer not in the manual?

Questions and answers

Summary of Contents for Ventrac ED202

  • Page 1 Operator’s Manual & Parts Drawings Edger Model ED202 Revised 10/26/18 Original Operator’s Manual 09.10142 Rev. 02...
  • Page 2 To the Owner Contact Information and Product Identification If you need to contact an authorized Ventrac dealer for information on servicing your product, always provide the product model and serial numbers. Please fill in the following information for future reference. See the picture(s) below to find the location of the identification numbers.

  • Page 3: Table Of Contents

    TABLE OF CONTENTS INTRODUCTION PAGE 5 Product Description ..........................5 Why Do I Need an Operator’s Manual? ....................5 Using Your Manual ..........................6 Manual Glossary ............................6 SAFETY PAGE 7 Safety Decals ............................7 General Safety Procedures ........................8 Training Required ...........................8 Personal Protective Equipment Requirements ..................8 Operation Safety ............................8 Preventing Accidents ..........................9 Keep Riders Off ............................9...
  • Page 4 TABLE OF CONTENTS SPECIFICATIONS PAGE 23 Dimensions ............................23 Features ...............................23 PARTS PAGE 24 Main Frame ............................24 Gauge Wheel ............................26 Disc Mount Frame ..........................28 Optional Blower Frame & Inlet Screens ....................30 Optional Blower Housing ........................32 Optional Blower Drive Frame & Shields ....................34 Optional Blower Drive Shaft .........................36 Optional Blower Fan (D-Hex Spline Pulley &...

  • Page 5: Introduction

    53.0148 Product Description The Ventrac ED202 edger is designed for the sole purpose of edging along sidewalks, curbs, and cart paths, as well as edging and maintaining flower and mulch beds. Edging can be done on either the right or left side of the power unit per the operator’s choice.

  • Page 6: Using Your Manual

    Manual Glossary Power Unit A Ventrac tractor or other Ventrac engine powered device that may be operated by itself or with an attachment or accessory. Attachment A piece of Ventrac equipment that requires a Power Unit for operation.

  • Page 7: Safety

    SAFETY Safety Decals The following safety decals must be maintained on your ED202 edger. Keep all safety decals legible. Remove all grease, dirt, and debris from safety decals and instructional labels. If any decals are faded, illegible, or missing, contact your dealer promptly for replacements.

  • Page 8: General Safety Procedures

    SAFETY General Safety Procedures for Ventrac Power Units, Attachments, & Accessories Training Required • The owner of this machine is solely responsible for properly training the operators. • The owner/operator is solely responsible for the operation of this machine and prevention of accidents or injuries occurring to him/her- self, other people, or property.

  • Page 9: Preventing Accidents

    SAFETY General Safety Procedures for Ventrac Power Units, Attachments, & Accessories Operation Safety (continued) • If equipped with a high/low range feature, never shift between high and low range while on a slope. Always move the machine to level ground and engage the parking brake before shifting range.

  • Page 10: Operating On Slopes

    SAFETY General Safety Procedures for Ventrac Power Units, Attachments, & Accessories Operating On Slopes • Slopes can cause loss-of-control and tip-over accidents, which can result in severe injury or death. Be familiar with the emergency parking brake, along with the power unit controls and their functions.

  • Page 11: Maintenance

    • If the power unit, attachment, or accessory requires repairs or adjustments not instructed in the operator’s manual, the power unit, attachment, or accessory must be taken to an authorized Ventrac dealer for service. • Never perform maintenance on the power unit and/or attachment if someone is in the operator’s station.

  • Page 12: Hydraulic Safety

    SAFETY General Safety Procedures for Ventrac Power Units, Attachments, & Accessories Fuel Safety (continued) • Do not overfill fuel tank. Only fill to bottom of fuel neck, do not fill fuel neck full. Overfilling of fuel tank could result in engine flooding, fuel leakage from the tank, and/or damage to the emissions control system.
  • Page 13 SAFETY ED202 Safety Procedures • Prior to edging, ensure the work area is clear obstacles, hazards, and personnel. • Keep hands and feet away from the edger blade and the edging area. • Do not make sharp turns with the edging disc in the ground.

  • Page 14: Edger Setup & Configuration

    EDGER SETUP & CONFIGURATION Edger Configurations Bed Shaping Setup (Disc Concave Fac- ing Away From Frame) This section of the manual will explain various edger configurations and how to properly set up these When using the edger for bed shaping, the disc is configurations.

  • Page 15: Disc Position Setup

    EDGER SETUP & CONFIGURATION 6. Reinstall the disc guard (A) onto the bearing 3. With the disc positioned on the desired side of mount plate using the outer set of holes (B) to the main frame receiver tube, reinsert the disc position the guard over the edge of the disc.

  • Page 16: Setup For Left Side Operation

    EDGER SETUP & CONFIGURATION Setup For Left Side Operation The edger can be operated with the disc on the left side of the edger as well as the right. To set up edger for left side operation: 1. Remove the two ball pins (A) from the frame receiver tube and remove both the gauge wheel assembly and the disc frame assembly from the edger.

  • Page 17: General Operation

    GENERAL OPERATION Daily Inspection Detaching 1. Park the power unit on a level surface and set the parking brake.* 2. Lower the edger to the ground. Always set the parking brake, shut off power 3. Shut off power unit engine. unit engine, remove the ignition key, and ensure 4.

  • Page 18: Edger Disc Angle Adjustment

    The weight bar bracket (A) on the 4. If the cutting depth needs to be adjusted, loosen disc guard frame will accomodate three Ventrac the locking nut (A) on the adjustable link (B). weights (part # 47.0115).

  • Page 19: Discharge Direction Adjustment For Optional Blower Fan

    GENERAL OPERATION Discharge Direction Adjustment For Op- tional Blower Fan The fan housing can be rotated to direct the airflow to either the right or left side of the edger, depending on which side the edger disc is mounted. 1. Push the rotation index arm (A) toward the frame until the bolt disengages from the blower housing.

  • Page 20: Service

    Attention shown in the diagram. If If any component requires replacement, use only any of these original Ventrac replacement parts. conditions occur, the drive belt will require replacement. Cleaning and General Maintenance Attachment Drive Belt Replacement For best results, and to maintain the finish of the 1.

  • Page 21: Fan Drive Belt Replacement

    SERVICE Fan Drive Belt Replacement Storage Preparing the Edger for Storage 1. Detach the edger from the power unit. 2. Remove the front drive shaft cover (A) and the 1. Clean the edger to remove grass, dirt, and debris. top and bottom fan inlet screens (B) from the 2.

  • Page 22: Maintenance Schedule

    SERVICE Maintenance Schedule Maintenance Schedule Grease & Lubrication: See Lubrication Section Disc Shaft Bearing           Caster Wheel Pivot           Wheel Axle Bearing ...

  • Page 23: Specifications

    SPECIFICATIONS Dimensions Overall Height ........21 inches (53 cm) Overall Length .

  • Page 24: Parts

    PARTS ILLUSTRATED DRAWING Main Frame Use only original Ventrac Illustrated Parts - 24 replacement parts.
  • Page 25 15 ..62.1027 ....STAND, JACK EA600 ............1 Use only original Ventrac Illustrated Parts - 25 replacement parts.

  • Page 26: Gauge Wheel

    PARTS ILLUSTRATED DRAWING Gauge Wheel 53.0155 53.0148 Use only original Ventrac Illustrated Parts - 26 replacement parts.
  • Page 27 42 ..29.GF0001 ....GREASE FTG, 1/4 SAE ST ..........1 Use only original Ventrac Illustrated Parts - 27 replacement parts.

  • Page 28: Disc Mount Frame

    PARTS ILLUSTRATED DRAWING Disc Mount Frame Use only original Ventrac Illustrated Parts - 28 replacement parts.
  • Page 29 22 ..03.0013 ....PIN, BALL, 5/8 X 2-1/2 ........... . . 1 Use only original Ventrac Illustrated Parts - 29 replacement parts.

  • Page 30: Optional Blower Frame & Inlet Screens

    PARTS ILLUSTRATED DRAWING Optional Blower Frame & Inlet Screens Use only original Ventrac Illustrated Parts - 30 replacement parts.
  • Page 31 10 ..99.SF0406-1 ....BOLT, SMF 1/4-20 X 3/4 ........... . 8 Use only original Ventrac Illustrated Parts - 31 replacement parts.

  • Page 32: Optional Blower Housing

    PARTS ILLUSTRATED DRAWING Optional Blower Housing Use only original Ventrac Illustrated Parts - 32 replacement parts.
  • Page 33 24 ..62.0975 ....HOUSING, BLOWER ............1 Use only original Ventrac Illustrated Parts - 33 replacement parts.

  • Page 34: Optional Blower Drive Frame & Shields

    PARTS ILLUSTRATED DRAWING Optional Blower Drive Frame & Shields Use only original Ventrac Illustrated Parts - 34 replacement parts.
  • Page 35 12 ..62.0976 ....FRAME, J-SHAFT HOUSING ..........1 Use only original Ventrac Illustrated Parts - 35 replacement parts.

  • Page 36: Optional Blower Drive Shaft

    PARTS ILLUSTRATED DRAWING Optional Blower Drive Shaft Use only original Ventrac Illustrated Parts - 36 replacement parts.
  • Page 37 20 ..81.B045 ....BELT, B45 ............. . . 1 Use only original Ventrac Illustrated Parts - 37 replacement parts.

  • Page 38: Optional Blower Fan (D-Hex Spline Pulley & Spindle Shaft)

    PARTS ILLUSTRATED DRAWING Optional Blower Fan (D-Hex Spline Pulley & Spindle Shaft) Use only original Ventrac Illustrated Parts - 38 replacement parts.
  • Page 39 13 ..94.10 ..... .WASHER, FLAT 5/8 USS ........... 1 Use only original Ventrac Illustrated Parts - 39 replacement parts.

  • Page 40: Warranty

    180-days All Ventrac add-on kits and accessories such as: 3-point hitch, 12V front & rear power outlets, foot pedal, dual wheel kit, etc., will be covered under the above warranty periods provided they are installed by an Authorized Ventrac Dealer.
  • Page 41 (ii) loss, cost or expense relating to transportation or delivery of turf equipment from the location of owner or location where used by owner to or from any Authorized Ventrac Dealer; (iii) travel time, overtime, after hours time or other extraordinary repair charges or charge relating to repairs or replacements outside of normal business hours at the place of business of an Authorized Ventrac Dealer;...

Table of Contents