Samsung PS50A40 User Manual page 23

1 Connect a HDMI/DVI cable between the HDMI IN 2 jack on the TV and the PC output jack on your
computer.
2 Connect a 3.5mm Stereo/2RCA cable between the DVI IN (HDMI 2) [R-AUDIO-L] jack on the TV and
the Audio Out jack of the sound card on your computer.
3 Connect the Emitter to the 3D SYNC OUT port on the rear panel of the TV.
4 Turn the TV on and set the source of the TV to HDMI2.
For more information on the 3D glasses (including the Emitter), refer to the user manual of your 3D

glasses.
Adjust the PC resolution: PS50A470: 1024 x 768@60Hz,1360 x 768@60Hz

Optimum PC resolution for PS50A470 is 1360x768. When 1024x768 signal is connected in 3D mode,

the picture will be shown in 4:3 format with left and right side grey bars appeared.
The 3D IR Emitter communicates with the 3D glasses.

Therefore, the 3D IR Emitter should be located near the 3D glasses.
It is activated when the HDMI or DVI input signal is RGB, and DVI Sound is supported.

When the power is turned on or off, the mode changes to the default (Off) and the Format is saved.

The 3D Effect is turned on or off regardless of the Picture Mode.

When 3D Effect is on, only the Contrast, Brightness, 3D Effect, and Reset picture menus are

activated.
To use the 3D Effect function, a graphics card supporting 3D or 3D software is required.

The 3D glasses and the Emitter must be manufacturer by the same company.

If you play a game or watch TV while wearing the 3D glasses for long periods of time, you may

experience eyestrain or a headache.
3D glasses (including the Emitter) not manufactured by Samsung may not be supported.

If you find the screen flickering while the 3D function is used, change the environmental lighting

darker or turn off the fluorescent lamp to watch the screen for its best condition.
Changing the Mode
Changing the Mode will exchange the pictures for each eye by
exchanging the left and right output signals.
1 Connect the TV, PC and 3D IR Emitter as shown in the figure.
2 Press the SOURCE button to select HDMI .
3 Press the MENU button to display the menu.
Press the ▲ or ▼ button to select Picture, then press the
ENTER button.
4 Press the ▲ or ▼ button to select Picture, Option then press
the ENTER button.
Press the ▲ or ▼ button to select 3D Effect then press the
ENTER button.
5 Press the ▲ or ▼ button to select Mode, then press the
ENTER button.
Press the ▲ or ▼ button to select Off, Mode1, Mode2 or 2D
Conversion then press the ENTER button.
• Off : Turns the 3D Effect function off.
• Mode1 : Mode 1 operates with right sync first.
• Mode2 : Mode 2 operates with left sync first.
• 2D Conversion : Provides picture converted 3D to 2D.
You can choose this to watch 2D picture temporally when you feel

dizzy, but you should choose "Off" to end 3D Effect completely.
If the 3D effect is not working properly, it means the Mode and

3D glasses may not be syncing properly. To put them in sync,
switch to the other mode.
English - 23
T V Picture
Mode : Standard
Cell Light
Contrast
Brightness
Sharpness
Colour
Tint G50
Detailed Settings
Picture Options
Reset : OK
Move Enter
T V Picture Options
Colour Tone : Normal
Size : Auto Wide
Screen Mode : 16:9
Digital NR : Auto
Real 100 Hz Demo : Off
DNle : Off
HDMI Black Level : Normal
Blue only mode : Off
Screen Burn Protection
3D Effect
Move Enter
T V 3D Effect
Mode :
Off
Format :
Mode1
Mode2
2D Conversion
Move Enter
Continued...

7
95
45
50
50
R50



Return









Return
Return