Page 1
SE-102-N Digital Signage Player User’s Manual Version 1.0 (Jan. 2018)
Page 2
Trademarks All the trademarks, registrations and brands mentioned herein are used for identification purposes only and may be trademarks and/or registered trademarks of their respective owners. SE-102-N User Manual...
CAUTION There is a danger of explosion if the lithium-ion battery is replaced with an incorrect battery. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries by observing local regulations. SE-102-N User Manual...
* PRODUCTS, HOWEVER, THAT FAIL DUE TO MISUSE, ACCIDENT, IMPROPER INSTALLATION OR UNAUTHORIZED REPAIR SHALL BE TREATED AS OUT OF WARRANTY AND CUSTOMERS SHALL BE BILLED FOR REPAIR AND SHIPPING CHARGES. SE-102-N User Manual...
Chapter 1 General Information The information provided in this chapter includes: • Features • Packing List • Specifications • Optional Accessories • Overview • Dimensions...
1.1 Introduction The SE-102-N is an ultra slim, fanless digital signage player that measures only 19.5mm thick. The media player enables the retail, food and hospitality segments to deliver compelling and valuable content in dual high-definition HDMI displays to targeted audiences in outdoor environments. It has been tested to pass extended operating temperatures (-40°C to +70°C) and meet...
E-series only) 1.3 Packing List If you buy a barebone SE-102-N, your product package should include the items listed below. If any of the items below is missing, contact the distributor or the dealer from whom you have purchased the product.
2 x HDMI 1.4b with hardware EDID emulation 1 x GbE RJ45 LAN port Serial 1 x RJ45 for COM1 RS-232 port 3 x USB 3.0 Audio Jack 1 x Line-Out Power Jack 1 x DC-In power jack 1 x SIM card slot SE-102-N User Manual...
Page 12
For CPU E-series processor: -40 ~ 85 °C (-40 ~ 185 °F) For CPU N-series processor: -10 ~ 80 °C (14 ~ 176 °F) Relative 10 ~ 90% (non-condensing) Humidity All specifications are subject to change without prior notice. SE-102-N User Manual...
USB 3.0 Ports Antenna Hole EDID Button* Be sure to press the EDID button to acquire or change the EDID data when the connected display/monitor cannot be recognized, or the displayed image does not fit the screen. SE-102-N User Manual...
To remove a module, use your fingers to press the clips outwards until the module pops up. Grab the module gently and pull it out of the slot. SE-102-N User Manual...
1. Fasten the hex nut and the washer. 2. Apply adhesive around here. Install the antenna. Info: The diameter of the nut is around 6.35 mm (0.25”-36UNC). SE-102-N User Manual...
1. Remove the screw indicated below. 2. Align the power cable holder enclosed in the product package to the screw hole and the DC jack as shown below and secure it with a supplied round- head screw. SE-102-N User Manual...
The method of mounting must be able to support the weight of the SE-102-N plus the weight of the suspending cables attached to the system. Use the following methods for mounting your system: Wall Mounting Installation 1.
1 2 3 When two pins of a jumper are encased in a jumper cap, this jumper is closed, i.e. turned On. When a jumper cap is removed from two jumper pins, this jumper is open, i.e. turned Off. SE-102-N User Manual...
Be sure to press the EDID button to acquire or change the EDID data when the connected display/monitor cannot be recognized, or the displayed image does not fit the screen. 2.4.1 Clearing CMOS Data (JP1) Function Pin closed Jumper Normal (default) Clear CMOS SE-102-N User Manual...
Motherboard Information 2.4.2 Clearing ME Register (JP2) Function Pin closed Jumper Normal (default) Clear ME 2.4.3 Battery Connector (BAT1) Signal Name Signal Name Battery+ Ground SE-102-N User Manual...
INF files for Plug & Play function for the chipset components. Follow the instructions below to complete the installation. 1. Run the Setup.exe file. ® 2. When the Welcome screen to the Intel Chipset Device Software appears, click Next to continue. SE-102-N User Manual...
Page 27
3. Accept the license agreement and proceed with the installation process. 4. On the Readme File Information screen, click Install. 5. Installation is now complete. Restart the system for changes to take effect. SE-102-N User Manual...
Driver Installation ® 3.3 Intel Graphics Driver Installation 1. Run the Setup.exe file. 2. When the Welcome screen appears, click Next to continue. 3. Click Yes to agree with the license agreement and continue the installation. SE-102-N User Manual...
Page 29
4. On the Readme File Information and Setup Progress screen, click Next until the installation starts. 5. Installation is now complete. Restart the system for changes to take effect. SE-102-N User Manual...
1. Run the Setup.exe file and the wizard starts. 2. On the Welcome screen of the InstallShield Wizard, click Next to start installing the audio driver on your system. 3. Installation is now complete. Restart the system for changes to take effect. SE-102-N User Manual...
3.5 LAN Driver Installation 1. Run the Setup.exe file. 2. On the Welcome screen of the InstallShield Wizard, click Next to continue. 3. Accept the license agreement and click Next. SE-102-N User Manual...
Page 32
Driver Installation 4. On the Setup Options screen, tick the checkbox to select the desired driver(s) and click Next. 5. Click Install. 6. Installation is now complete. Restart the system for changes to take effect. SE-102-N User Manual...
® 3.6 Intel Trusted Execution Engine Drivers Installation 1. Run the Setup.exe file. 2. When the Welcome screen appears, click Next. 3. Accept the license agreement and click Next until the installation starts. SE-102-N User Manual...
Page 34
Driver Installation 4. Installation is now complete. Restart the system for changes to take effect. SE-102-N User Manual...
® 3.7 Intel Serial IO Drivers Installation 1. Run the Setup.exe file. 2. When the Welcome screen appears, click Next. 3. Accept the license agreement and click Next until the installation starts. SE-102-N User Manual...
Page 36
Driver Installation 4. Installation is now complete. Restart the system for changes to take effect. SE-102-N User Manual...
Chapter 4 BIOS Setup This chapter describes the different settings available in the AMI BIOS that comes with the board. The topics covered in this chapter are as follows: • Main Settings • Advanced Settings • Chipset Settings • Security Settings •...
These defaults have been carefully chosen by both AMI and your system manufacturer to provide the absolute maximum performance and reliability. Changing the defaults could make the system unstable and crash in some cases. SE-102-N User Manual...
4.3 Main Settings BIOS Setting Description System Date Sets the date. Use the <Tab> key to switch between the data elements. System Time Set the time. Use the <Tab> key to switch between the data elements. SE-102-N User Manual...
BIOS Setup 4.4 Advanced Settings This section allows you to configure, improve your system and allows you to set up some system features according to your preference. SE-102-N User Manual...
Enables / Disables the system ability to hibernate (OS/S4 Sleep State). This option may be not effective with some OS. ACPI Sleep State Selects an ACPI sleep state (Suspend Disabled or S3) where the system will enter when the Suspend button is pressed. SE-102-N User Manual...
For example, if setting up a schedule from Wednesday 5 p.m. to Thursday 2 a.m., configure two schedule slots. But if setting up a schedule from 3 p.m to 5 p.m. on Wednesday, configure only a schedule slot. SE-102-N User Manual...
Options: All Enable / Enable Ethernet for WOL / All Disable Serial Port Configuration Sets parameters of Serial Ports (COMA). Enables / Disables the serial port and select an optimal setting for the Super IO device. SE-102-N User Manual...
Page 44
IO = 2E8h; IRQ = 3, 4, 5, 6, 7, 9, 10, 11, 12 Device Mode Changes the serial port mode to: • RS232 • RS485 TX Low Active • RS485 with Termination TX Low Active • RS422 • RS422 with Termination SE-102-N User Manual...
PC health status. CPU Shutdown This field enables or disables the Shutdown Temperature Temperature. Options: Disabled / 70 °C / 75 °C / 80 °C / 85 °C / 90 °C / 95 °C SE-102-N User Manual...
Socket 0 CPU Information Displays the socket specific CPU information. CPU Power Management Allows you to enable / disable Turbo Mode. Active Processor Cores Enables / Disables the cores in the processor package. Monitor Mwait Enables / Disables Monitor Mwait. SE-102-N User Manual...
Enables / Disables the turbo mode. Boot Performance Mode Selects the performance state that the BIOS will set before OS handoff. Options: Max. Performance, Max. Battery Power Limit 1 Enable Enables / Disables Power Limit 1. 4.4.6 AMI Graphic Output Protocol Policy SE-102-N User Manual...
If disabled, Ipv4 HTTP boot option will not be created. PXE boot wait time Assigns a period of time to press ESC key to abort the PXE boot. Media detect count Assigns a number of times to check the presence of media. SE-102-N User Manual...
OXE OpROM. Storage Controls the execution of UEFI and Legacy Storage OpROM. Video Controls the execution of UEFI and Legacy Video OpROM. Other PCI devices Determines OpROM execution policy for devices other than network, storage or video. SE-102-N User Manual...
The maximum time the device will take before it properly reports itself to the Host Controller. “Auto” uses default value for a Root port it is 100ms. But for a Hub port, the delay is taken from Hub descriptor. SE-102-N User Manual...
BIOS Setup 4.5 Chipset Settings BIOS Setting Description North Bridge Displays the North Bridge parameters Max TOLUD Maximum value of TOLUD. SE-102-N User Manual...
4.6 Security Settings BIOS Setting Description Administrator Password Sets an administrator password for the setup utility. User Password Sets a user password. SE-102-N User Manual...
Selects a Boot mode. Boot Option Priorities Sets the system boot order priorities for hard disk, CD/DVD, USB, Network. LEFI Hard Disk Drive Specifies the boot device priority sequence from BBS Priorities available UEFI Hard Disk Drives. SE-102-N User Manual...
Restore Defaults Restores / Loads defaults values for all the setup options. Save as User Defaults Saves the changes done so far as user defaults. Restore User Defaults Restores the user defaults to all the setup options. SE-102-N User Manual...
Appendix This section provides the mapping addresses of peripheral devices and the sample code of watchdog timer configuration. • I/O Port Address Map • Interrupt Request Lines (IRQ) • Watchdog Timer Configuration...
Motherboard resources 0x0000F040-0x0000F05F Intel(R) Celeron(R)/Pentium(R) Processor SMBUS - 5AD4 0x000003F8-0x000003FF Communications Port (COM1) 0x000002F8-0x000002FF Communications Port (COM2) 0x0000E000-0x0000EFFF Intel(R) Celeron(R)/Pentium(R) Processor PCI Express Root Port - 5AD8 0x00000000-0x0000006F PCI Express Root Complex 0x00000078-0x00000CF7 PCI Express Root Complex SE-102-N User Manual...
Page 58
0x000000B8-0x000000B9 Programmable interrupt controller 0x000000BC-0x000000BD Programmable interrupt controller 0x000004D0-0x000004D1 Programmable interrupt controller 0x0000F000-0x0000F03F Intel(R) HD Graphics 0x0000F090-0x0000F097 Standard SATA AHCI Controller 0x0000F080-0x0000F083 Standard SATA AHCI Controller 0x0000F060-0x0000F07F Standard SATA AHCI Controller 0x00000040-0x00000043 System timer 0x00000050-0x00000053 System timer SE-102-N User Manual...