Advertisement
Quick Links
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation. Changes or modifications not expressly approved by
the party responsible for compliance could void the user's authority to operate the
equipment.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference
that may cause undesired operation of the device.
Cet appareil s'accorde avec Industrie Canada licence-exempte RSS standard. (1) cet
appareil ne peut pas causer l'intervention, et (2) cet appareil doit accepter de
l'intervention, y compris l'intervention qui peut causer l'opération non désirée de
This Class【B】 digital apparatus complies with Canadian ICES-003.
Operating Instructions
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Locator Model ETP-LOC-01
Tag Model ETP-TAG-01
Copyright © 2011 Eureka Technology Partners, LLC ALL RIGHTS RESERVED
Protected under the following US and Foreign Patents:
US 6,788,199 US 7,148,801 CA 2438172 AU 2002255750
1
2
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Eureka MARCO POLO ETP-LOC-01
Summary of Contents for Eureka MARCO POLO ETP-LOC-01
- Page 1 Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. Locator Model ETP-LOC-01 Tag Model ETP-TAG-01 Copyright © 2011 Eureka Technology Partners, LLC ALL RIGHTS RESERVED Protected under the following US and Foreign Patents: US 6,788,199 US 7,148,801 CA 2438172 AU 2002255750...
-
Page 2: User Controls And Displays
If you are a new pet owner you should seek the advice of a trained Button professional regarding the proper enclosure and environment for your pet. Eureka Technology Partners, LLC makes no warranties regarding loss of property or personal injury, even if the loss was due to a malfunction of the Down Product. - Page 3 Marco Polo Operating Instructions Marco Polo Operating Instructions Battery Search Directional Signal Status Indicator Arrows Strength Bars Tag Low Battery Indicator Alarm Settings Setup Selections Boundary Settings Status Messages Charging Jacks Distance Percentage Mode Box Figure 3 Tag Mode Figure 2 Location of Charging Indicators Locator Display Elements...
- Page 4 Marco Polo Operating Instructions Marco Polo Operating Instructions Powering On the Locator and Tag To power on the locator: Press and hold the Power button (see Figure 1 for the location of the power button) until all of the display segments flash and the locator beeps twice.
- Page 5 Marco Polo Operating Instructions Marco Polo Operating Instructions Backlight Each time you press a button on the locator the display’s backlight will come on for 5 seconds. The Select button can be used to turn on the backlight when needed. If you need the backlight to be on for a more extended time, short presses of the Power button will latch the power on or off.
- Page 6 Marco Polo Operating Instructions Marco Polo Operating Instructions Tracking Once the paging operation has been successful the tracking display will appear as shown in Figure 8. Directional Arrow Points in the Direction of Your Pet Tag Icon Flashes Each Time the Pet’s Tag Responds Flashing Signal Strength...
- Page 7 Marco Polo Operating Instructions Marco Polo Operating Instructions on your footing when searching at night. To turn the beeping off, press the locator is unable to calculate a direction after four consecutive attempts. As Down button. long as a response is received from your pet’s tag the signal strength information will be updated, even if a direction can not be determined.
- Page 8 Marco Polo Operating Instructions Marco Polo Operating Instructions Remote An audible tone is generated by the locator plus, after two additional monitoring checks show the pet is outside the designated Flashing area, the external alarm output is activated. Please check eurekaproducts.com to see the available accessory devices that can be used with this output.
- Page 9 Marco Polo Operating Instructions Marco Polo Operating Instructions Medium This setting will work for most homes with two stories and a medium to large yard area. This is the factory default setting Monitoring mode begins just like tracking mode by paging the selected pet’s tag.
- Page 10 Marco Polo Operating Instructions Marco Polo Operating Instructions If the monitored pet strays outside the selected boundary area and stays there for 90 seconds or more then Alarm be activated on the locator. The alarm display will appear as shown in Figure 13. 7 sec Focus on Pet 1 Focus...
- Page 11 Marco Polo Operating Instructions Marco Polo Operating Instructions around the neighborhood. If you do not get any response from your Switching Between Modes pet’s tag then make larger loops or crisscross the area to widen the You can transition a pet’s tag directly from one mode to another by pressing its search.
- Page 12 Marco Polo Operating Instructions consistent change in the indicated direction. Verify that the signal strength is generally increasing (more signal strength bars, higher percentage readings and/or more beeps) as you move along. When you are close to your pet the directional information will become much more sensitive.
Need help?
Do you have a question about the MARCO POLO ETP-LOC-01 and is the answer not in the manual?
Questions and answers