Huskie Tools HTP-AGR Operating Instructions Manual

Cordless angle grinder

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

IMPORTANT

This manual contains safety information. Read manual completely before first using this product and save this

manual for future use.

IMPORTANTE

Este manual contiene información de seguridad. Lea completamente este manual antes de utilizar por primera

vez este producto, y guárdelo para poder consultarlo en el futuro.

Cordless Angle Grinder

Amoladora angular inalámbrica

Operating Instructions

Manual de instrucciones

Model No: HTP-AGR

Table of Contents

Summary of Contents for Huskie Tools HTP-AGR

Page 1: Operating Instructions
Cordless Angle Grinder Amoladora angular inalámbrica Operating Instructions Manual de instrucciones Model No: HTP-AGR IMPORTANT This manual contains safety information. Read manual completely before first using this product and save this manual for future use. IMPORTANTE Este manual contiene información de seguridad. Lea completamente este manual antes de utilizar por primera...
Page 2: Functional Description
Index/Index/Indice English: Page Español: Página FUNCTIONAL DESCRIPTION DESCRIPCIÓN FUNCIONAL (D) (E) (F) (D) (E) (F) (E) (F) 10.8 V ─ 28.8 V 10.8 V ─ 28.8 V...
Page 3 Power switch Brush cap Interruptor de alimentación Tapa de cepillo Display panel Battery low warning lamp Panel de exhibición Luz de aviso de baja carga de batería Overheat warning lamp (battery) On lock warning lamp Luz de advertencia de sobrecalentamiento Luz de advertencia de bloqueo (batería) Battery pack release button...
Page 4 [Fig.1] [Fig.2] [Fig.3] 1. Grinding disc guard Make sure the side. Protección de disco de desbastado Assurez-vous du côté. Asegure el costado. 2. Spindle 3. Grinding disc guard fixing screw Tornillo de fijación de protector de disco de amoladora 1. Clamp nut 3.
Page 5 [Fig.11] [Fig.12] Make sure the side. Asegure el costado. 1. Clamp nut 3. Disc flange Tuerca de abrazadera Brida de disco [Fig.13] ON→OFF OFF→ON 2. Cut-off disc 4. Spindle ON→OFF OFF→ON Disco de corte [Fig.14] Off (normal operation) Apagado (funcionamiento normal) Flashing: Overheat Destella: Sobrecalentamiento [Fig.15]...
Page 6: Limited Warranty
I. INTRODUCTION in serious injury or death if not avoided. DANGER Thank you for purchasing the Huskie Tools Angle Grinder. The power- Danger indicates an imminent hazard ful grinding action of this tool, combined which will result in serious injury or with the convenience of its recharge- death if not avoided.
Page 7: Work Area Safety
Personal Safety SAVE THESE INSTRUCTIONS Work Area Safety 1) Stay alert, watch what you are doing and use common sense 1) Keep work area clean and well lit. when operating a power tool. Do Cluttered or dark areas invite not use a power tool while you accidents.
Page 8 Power Tool Use and Care Battery Tool Use and Care 1) Do not force the power tool. Use 1) Ensure the switch is in the off the correct power tool for your position before inserting battery application. pack. The correct power tool will do the job Inserting battery pack into power better and safer at the rate for which tools that have the switch on invites...
Page 9: Safety Instructions For All Operations
Safety instructions for all 7) Do not use a damaged accessory. Before each use inspect the operations accessory such as abrasive wheels for chips and cracks. Safety warning common for Grinding If power tool or accessory is or Abrasive Cutting-off operations: dropped, inspect for damage or 1) This power tool is intended to install an undamaged accessory.
Page 10: Further Safety Instructions For All Operations
12) Never lay the power tool down 1) Maintain a firm grip on the power until the accessory has come tool and position your body to a complete stop. The spinning and arm to allow you to resist accessory may grab the surface and kickback forces.
Page 11: Additional Safety Warnings Specific For Abrasive Cutting- Off Operations
3) The guard must be securely 3) When wheel is binding or when attached to the power tool and interrupting a cut for any reason, positioned for maximum safety, switch off the power tool and hold so the least amount of wheel is the power tool motionless until exposed towards the operator.
Page 12: Important Safety Instructions
• Huskie Tools is not responsible for 2) Before using battery charger, read all any damage or accident caused instructions and cautionary markings by the use of the recycled battery...
Page 13 a. that pins on plug of extension cord 17) Do not incinerate the battery pack. It are the same number, size and can explode in a fire. shape as those of plug on charger. 18) Avoid dangerous environment. Do b. that extension cord is properly not use charger in damp or wet wired and in good electrical locations.
Page 14: Attaching Or Removing Battery Pack
IV. ASSEMBLY 3. Tighten the clamp nut onto the spindle so that hollow side faces opposite direction to the disc. NOTE: 4. Push the Spindle lock button to secure When attaching or removing a support the spindle in place, and then use the handle, disconnect battery pack from clamp nut wrench to tighten the clamp tool.
Page 15: Power Switch Operation
V. OPERATION CAUTION After operation, always switch off the NOTE: tool and wait until the wheel has come Be aware that this tool is always in an to a complete stop before putting the operating condition, since it does not tool down.
Page 16 Overheat warning lamp • Do not jam the Disc or apply excessive pressure. Do not attempt to make an [Fig.14] excessive depth of cut. Overstressing Indicates operation has been halted due the cut-off disc increases the loading and susceptibility to twisting or to motor or battery overheating.
Page 17: Li-Ion Battery Pack
Battery low warning lamp The life of the battery pack terminals may be affected by foreign [Fig.15] substances such as dust and water Excessive (complete) discharging of etc. during operation. lithium ion batteries shortens their • When battery pack is not in use, service life dramatically.
Page 18: For Safe Use
[Battery Charger] Recommendations for use [Fig.17] Charging Be sure to use the Pack cover CAUTION • When the battery pack is not being used, • The charger is designed to operate store the battery in a way that foreign on standard domestic electrical substances such as dust and water etc.
Page 19: How To Charge
How to charge 4. The charge lamp (green) will flash slowly once the battery is approximately 1. Plug the charger into the AC outlet. 80% charged. NOTE: 5. When charging is completed, the Sparks may be produced when the charging lamp in green color will turn off. plug is inserted into the AC power 6.
Page 20: Maintenance
RELIABILITY, repairs, any other • Hole diameter: Φ22mm (7/8”) maintenance or adjustment should be • Flat disc only performed by Huskie Tools Authorized or Factory Service Centers, always Cut-off Disc Guard (For cut-off disc) using Huskie Tools replacement parts. • WHTP-AG VI.
Page 21: Specifications
VIII. SPECIFICATIONS MAIN UNIT Mounting wheel diameter Φ125mm (4 -29/32) Spindle thread size Mounting wheel hole diameter 22mm (7/8) Weight 1.65kg (3.63lbs) (main unit only) Overall length 300mm (11- 13/16) (main unit only) Motor voltage DC 18 V Rated speed 10000min (rpm) BATTERY PACK...
Page 22: Harmonized Standards
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Page 23 195 Internationale Blvd Glendale Heights, IL 60139 Phone 800-860-6170 Fax 800-345-3767 www.huskietools.com...