Advertisement
Locking
g:
1.
Pre
ess; ON, Yo
asc
cending bee
2.
Tu
rn handle to
Openin
ng with Use
1.
Pre
ess; ON
2.
Inp
put; 1,2,3,4,o
3.
Inp
put your 4 d
4.
Lo
ck unlocked
loc
ck.
Openin
ng with pro
1.
Pre
ess; ON
2.
Inp
put; 0
3.
Inp
put; 7-8-9-0
4.
Lo
ck unlocked
loc
ck. The gree
Cau
ution!!
At this m
mo
de.
The prog
gramming cod
Openin
ng with the
e
The 1
ma
ster code is onl
1.
Pre
ess and hol
gre
een led light
co
ntinuously
2.
Inp
put; 7
3.
Inp
put; 1-2-3-4
4.
Lo
ck unlocked
10
sec. Turn h
Changi
ng the pro
Caution!
All changes
1.
Pre
ess; ON
2.
Inp
put; 0
3.
Inp
put; 7-8-9-0
4.
Lo
ck unlocked
for
r 10 sec. Tur
Inp
put (Whilst t
new
w 4-digital m
1 1
Quic
k start
(vo
ou can hear
three 3
eps
o close the l
lock.
er code:
or 5 (Your e
ntrance dig
igit code.
d. Turn hand
dle to open
gramming
code:
0 = Factory c
code
d. Turn han
ndle to open
en led stays
on for 10 se
moment the loc
ck is in progra
de is
not
a us
ser code.
master co
de:
y used in an em
mergency when
d the ON bu
utton until th
ts. The gree
en LED stays
4-5-6 = Facto
ory code.
d. the Green
n led stays o
handle to op
pen the lock
ogramming
code:
must be initi
iated with the
0 = Factory c
code
d. The gree
n led stays
rn handle to
o open the lo
the LED is s
still on) 0 an
master code
e
Guide
ESL-C
oor 5 fixed use
ers)
it)
1
the
0
n the
ec.
mming
the User code i
is
unknown.
he
s on
on fot
.
e lock in lock
ed position.
0
on
ock.
d a
CAM
Changing
g in reservati
versie
on
1.0 2010
Advertisement
Table of Contents
Summary of Contents for Mauer ESL-CAM
- Page 1 Quic k start Guide ESL-C oor 5 fixed use ers) Locking ess; ON, Yo ou can hear three 3 cending bee rn handle to o close the l lock. Openin ng with Use er code: ess; ON put; 1,2,3,4,o or 5 (Your e ntrance dig put your 4 d igit code.
- Page 2 Quic k start Guide ESL-C oor 5 fixed use ers) Program mming a Use er code: (The lock k can be used by 5 different users). ess; ON put; progra amming cod ck unlocked d. The gree n led stays on for sec. Turn h handle to op pen the lock put a 1,2,3,4...
Need help?
Do you have a question about the ESL-CAM and is the answer not in the manual?
Questions and answers
Hallo:Ich habe kein Handbuch mehr und leider hat es eine Lehrperson geschaft die code einstellung zu stören.Wie kriege ich das zu rückgesetzt
To reset the code settings on a Mauer ESL-CAM lock:
1. Press and hold the ON button until the green LED lights continuously.
2. Input: 7
3. Input the master factory code: 1-2-3-4-4-5-6
4. The lock unlocks and the green LED stays on for 10 seconds.
5. While the LED is still on, input a new 6-digit master code.
For deleting a user code:
1. Press ON.
2. Input: 0 0
3. Input the programming code.
4. Turn the handle to open the lock.
5. Input the entrance digit (1 to 5). If the LED turns off, the user code is deleted.
If the procedure fails, repeat the steps from the beginning.
This answer is automatically generated
@Mr. Anderson
Was heist Eingang 7
ist jetzt offen,wie kann ich **** einen neuen code eingeben,oder kann der alte wieder eingestellt werden
To enter a new user code or reset the old one on the Mauer ESL-CAM:
1. Make sure the lock is in the locked position.
2. Press and hold the ON button until the green LED lights up and stays on.
3. Input: 7 7
4. Input the factory master code: 1-2-3-4-4-5-6
5. The lock will unlock and the green LED stays on for 10 seconds.
6. While the LED is still on, input a new 6-digit master code.
To change or delete a user code:
1. Press ON
2. Input: 0 0
3. Input the programming code (factory code is 7-8-9-0-0)
4. Lock unlocks and green LED stays on for 10 seconds.
5. To delete: input the entrance digit (1–5). If LED goes off, the user code is deleted.
6. To add/change: Input entrance digit (1–5) + a new 4-digit user code.
Note: Complete the steps within the time limit or start over.
This answer is automatically generated