Summary of Contents for Aim EVO5
- Page 1 EVO5 Logger USER GUIDE AiM TECH Srl. Via Cavalcanti, 8 20063 Cernusco S/N (MI) Italia Tel. (+39) 02.9290571 www.aim-sportline.com Made in Italy...
-
Page 2: Table Of Contents
09 Digital outputs 10 WiFi configuration 10.1 Configuring your device as an AP Dear Customer, 10.2 Joining your AiM system to an existing network 10.3 High performance WLAN setup First, we would like to thank you for 10.4 About Internet connectivity choosing the EVO5 logger as the tool for 10.5 Working with Mac... -
Page 3: Introduction
The top RGB LED, changing colour and format and new .XRK? years, has become a standard de facto blinking frequency, tells you if EVO5 is .XRK, taking advantage of GPS acquisition system in a huge amount performing a firmUp, if it is in error, if it... -
Page 4: What Is In The Kit
CHAPTER 2 WHAT IS IN THE KIT EVO5 2. What is in the kit The EVO5 kit includes: EVO5 logger with SD card Harness GPS08 Module Software... -
Page 5: Layout And Pushbuttons
CHAPTER 3 LAYOUT AND PUSHBUTTONS EVO5 EVO5 Logger Aluminum Body RGB LED SD card slot Deutsch 37pin Deutsch 22pin... -
Page 6: Rgb Led
EVO5 4. RGB LED 5. ECU connection and CAN resistors EVO5 features an RGB LED on top of it near The system can acquire data from the ECU to the SD Card slot. of your vehicle. The list of the available ECU protocols is published on our site: www.aim-sportline.com/download area,... -
Page 7: Rpm
The system can receive the RPM signal from three different sources: 5-50V output that can be directly acquired n From ECU from EVO5. n Through a square wave signal (8 to 50 V) If the output is not available from the... -
Page 8: Speed
EVO5 7. Speed 8. Analog inputs 7.3 Speed read from wheel sensors EVO5 has 8 analog inputs, recorded up to Please follow these steps, using the soft- The system can receive the speed signal 1000 times per second each. ware Race Studio 3 to set the channels:... -
Page 9: Digital Outputs
Each of them can give an output of 1 amp resistor. the analog or digital inputs, ECU values, ex- you turn EVO5 off, when you push a at 12 volts. Here below are some connecting examples. pansions values, GPS information or math pushbutton or when the data are channels. -
Page 10: Wifi Configuration
Using both network and device authentication allows for various security strategies where multiple people, PCs and AiM devices are involved. For example a PC on a WLAN may see se- veral AiM devices but can only communicate with AiM devices for which it has the password. -
Page 11: Configuring Your Device As An Ap
Access Point and creates a network without a password completely accessible to everyone. So, for establishing the WiFi connection: n Be sure your AiM system has the WiFi enabled. n Read its name in the lower part of the Live Measures page. - Page 12 CHAPTER 10 WIFI CONFIGURATION EVO5 The name of this AP, or SSID, is unique to your device. An example is: "AiM-EVO5-5000999" whereas: n “AiM” is the prefix for all AiM devices n “EVO5” is type of system identifier n “5000999” is a unique serial number for your device assigned at the factory.
-
Page 13: Joining Your Aim System To An Existing Network
Devices, just as if connected via USB. Race Studio 3 will display all devices con- nected to the same network. If the AiM device is connected to your PC using a WLAN, it is possible to have two dif- Connected devices can be seen under the ferent passwords: the device password and "Connected Devices"... - Page 14 Once the user’s PC is authenticated to the same network called “network_1, ” it can see the AiM device previously configured to gain access to the target network. As you can see in the picture above, one device called “EVO5 ID 5000999” is switched from AP mode to WLAN mode.
-
Page 15: High Performance Wlan Setup
AiM device on this network. a user’s PC on it. AiM suggests the use of a Linksys AS3200 device as the network device in order to provide a n Gateway address: 192.168.0.1 WLAN. -
Page 16: About Internet Connectivity
Ethernet interface. mal data network speed for your AiM de- as your AiM device(s) but doing so can de- vice(s) and simultaneously provide grade the performance of AiM device com- Internet access via the second NIC. - Page 17 CHAPTER 10 WI FI CONFIGURATION EVO5 If you want to be sure the communication In Race Studio 3 flag the checkbox you find is working, choose the in "Preferences –> WiFi Settings" “Open Network Preferences…” menu. In the window you are prompted verify that the status is shown as "Connected" and that the...
-
Page 18: Race Studio 3 Software
When you connect an from our site www.aim-sportline.com. pressure) and fixing download settings. AiM logger, its serial number appears in the Custom sensors Creates, imports, exports and modifies cu- Connect to AiM website... -
Page 19: Channels Configuration
CHAPTER 11 RACE STUDIO 3 SOFTWARE EVO5 After having entered the configuration page you can see different tabs, which are useful for By clicking on each line, a menu appears: selecting one of the following configuration features: You can define:... - Page 20 CHAPTER 11 RACESTUDIO3 SOFTWARE EVO5 Here you can: n configure channel name (afterwards, that name will not be automatically modi- fied) n configure parameters like measure unit, decimals number and sampling frequency, which will not be assigned just to that...
-
Page 21: Ecu Stream And Can Resistor Configuration
CHAPTER 11 RACE STUDIO 3 SOFTWARE EVO5 11.1.2 CAN resistor configuration ECU Stream and CAN resistor configuration A CAN line ending with a 120 Ohm resistor can be enabled/disabled through this checkbox. Push "ECU Stream" tab. Here you set the ECU driver as well as ena-... -
Page 22: Math Channels
CHAPTER 11 RACE STUDIO 3 SOFTWARE EVO5 11.1.4 Math Channels 11.1.5 Parameters Press "Math channels" tab. Using the button "Add Channel" you can calculate the engaged Press "Parameters" tab. Here you can set the lap detection (GPS or Optical beacon) as well as gear both with a learning lap (calculated gear) and filling in the RPM values (precalculated decide when start recording. -
Page 23: Output Signals
It is your responsibility to fully understand your vehicles CAN-bus. AiM cannot be held responsible for any damage or injury caused by misuse of this function. -
Page 24: Modify Or Delete An Existing Configuration
RACE STUDIO 3 SOFTWARE EVO5 11.2 Modify or delete an existing 11.3 Connect your AiM system to a PC configuration Push "All" tab top left of Race Studio 3 page; just under the pushbuttons. When you connect your system to the PC,... -
Page 25: Live Measures And Calibration
Storing data both in its memory and on the Push "Download" button for downloading Measures". SD card, EVO5 can download them via USB, the data recorded in your system. via WiFi or placing the SD card in the PC Push "Start Live Measures" to look the data slot. -
Page 26: Gps And Track Management
To transmit/receive track information to races on that track. EVO5, use "Tracks" feature, as explained in On the right side of the screen, if available, this section. you will find the track page with its logo, address, contact information, website and coordinates. -
Page 27: Tracks Collections
CHAPTER 12 GPS AND TRACK MANAGEMENT EVO5 12.2 Tracks Collections 3) Manual collections To create a Manual Collection of tracks click on the setting Icon, fill in the Collection You can see collections of tracks selecting name and click OK. -
Page 28: How To Modify Track Data In The Pc Database
12.4 How to delete a track from the PC database The tracks you find in the software by default and provided by AiM cannot be deleted. To delete a track you imported just select it and press "Delete" on the software top central keyboard. -
Page 29: Evo5 Pinout
CHAPTER 14 EVO5 PINOUT EVO5 14. EVO5 Pinout Deutsch 37pin Deutsch 22pin 9-15V Power Input Analog Input 5 Battery GND Analog GND CAN+ Exp +Vbattery +Vreference +Vbattery CAN Analog Input 6 CAN- Exp Analog Input 7 +Vbext Analog GND CAN1+ ECU... -
Page 30: Technical Drawings
YES: GPS Module, Channel Expansion, Lambda controller, SmartyCam HD - Analog inputs 8 fully configurable: 0-5V, 0-12V, K thermocouples Max frequency 1 KHz each Our web site aim-sportline.com is constantly - Digital inputs Coil, RPM and 4 speed inputs updated. - Inertial platform...
Need help?
Do you have a question about the EVO5 and is the answer not in the manual?
Questions and answers