SEA Praha GSM-R4-DIN Manual

GSM-R4-DIN, GSM-R4-DINB
1. Introduction
The GSM-R4-DIN and GSM-R4-DINB (
mounted on a DIN rail into a switchboard.
independent electrical circuits in a building e.g. circuit of an accumulator stove and
circuit for garage gate control. The control is made via SMS messages or by ringing.
After installation into an electrical box insert a SIM card of any GSM operator and the
device is ready to operate.
4
GSM rele
has 2 galvanically isolated digital outputs with a semiconductor
switch, which can control directly low power circuits up to 230V
to control directly e.g. a thermoregulator circuit of a gas boiler or a coil of one phase
contactor 230V AC. The contact of the contactor can then control either one phase
high power appliance (e.g. electrical radiator) or a coil of three phase contactor of an
accumulation stove.
GSM rele 4
has also 2 analog inputs for temperature measuring and 2 digital
inputs which can be activated by a contact from 4V power provided by
by an external voltage 3 to 30V DC.
regulators which use analog inputs from temperature sensors to maintain preset
temperature. The temperature of sensors can be readout via SMS.
There is an internal built in Li-Ion accumulator which enables to send an SMS in
case of a power failure and to restore the output status after a power failure. It's also
possible to monitor the status of inputs and temperatures via SMS during 230 V
power failure.
(1) OUTPUT 3, 4 (Y3, Y4) connectors
(2) Pushbuttons + LED (Y3, Y4)
(3) INPUT 1, 2 (X1, X2) LED
(4) INPUT 1, 2 (X1, X2) connectors
(5) DIN rail holder
(6) Temperature sensors connector (T5, T6)
(7) USB connector (for configuration)
4
GSM rele
(8) operation state LED indicators
(9) 230V Power supply connector
AC
(10) SIM card and MicroSD card holder
(11) External GSM antenna connector
( - ) Temperature sensor GSM-C-T2
2. Package Content
GSM rele 4
1 pc (order code GSM-R4-DIN or GSM-R4-DINB)
1 pc GSM antenna ANT05S
1 pc temperature sensor GSM-C-T2 (based on KTY81-210), cable - 1 meter
1 pc cable USB 2.0 A-B, 1.8m (order code HW-11.02.8818)
1 pc connector 5.00 mm
2 pcs connector 3.81 mm
1 pc connector 3.81 mm
1 pc connector 3.81 mm
1 pc screwdriver 2 mm
1 pc printed documentation
3. Installation
4
GSM rele
1. To operate the a SIM card of any GSM operator is necessary. SIM card
must be functional and active. Also some credit is necessary if SIM card is pre-
paid. We recommend to deactivate the PIN code for installation.
Before inserting the SIM card into the
recommend to turn off setting of the "PIN code"!
Insert the active SIM card (= at least one call was made) to any mobile
telephone and turn off the requirement of setting the PIN. On most mobile
telephones, this option can be found in menu "Setting the telephone
protection". or "Setup -> Security -> PIN control".
4
GSM rele
must be mounted by qualified personnel only!
2. Insert this prepared SIM card (cut off corner first) into a slot on the side of the
GSM rele 4
. The SIM card holder is located in a slot on side of
GSM antenna connector). The proper insertion is indicated by a slight mechanical
click noise. To remove the SIM card - press the SIM card in direction into the
4
GSM rele until mechanical click. The SIM card can be the freely removed.
3. Now it's possible to connect the device to 230V AC power supply. If the power
supply is correct, green LED diode POWER SUPPLY goes on. After about 20
seconds, blue LED diode GSM starts flashing with a period 1 per 3 sec.
GSM rele
4. For the first tests of
important. Please keep in mind that the devices connected to OUTPUTS will be
switched on during tests!
4
5. To test the GSM rele press the pushbutton bellow OUTPUT 3. The green LED
diode for OUTPUT 3 lights ON. Send an SMS from mobile phone (which will be
GSM rele
mainly used to control the
number of the SIM card inserted into the
plugged appliance. The green status LED for OUTPUT3 goes OFF. Simultaneously,
GSM-R4-DIN_EN (Version 1.02; 2016-04-06)
4
GSM rele for short) are designed to be
4
GSM rele can control two
/90mA. It's possible
AC
4
GSM rele has built in two automatic
11
10
1
2
3
4
5
4
GSM rele device, we
ATTENTION:
GSM rele
4
the connection of inputs and outputs is not
4
) in form 1234 Y3 OFF to the telephone
4
GSM rele . This will switch off the
the device automatically sends a confirmation SMS message on performing the
operation. The password 1234 can be changed later in configuration. The
4
GSM rele
reacts on the SMS text message from any telephone as long as the
access password matches. The very first one (the sender of the first valid SMS
message) will be remembered as master and will receive messages about events
4
GSM rele
on
6. Try "ringing" on device. You can make pulse on OUTPUT 4 for approx. 4 seconds
by calling to GSM rele
and makes pulse on the OUTPUT 4. This pulse can be used for example for
opening entrance gate. To test this function call from the phone (which was used
to send the first test SMS to switch off the OUTPUT 3). The pulse is indicated by
green LED.
7. Try regulation. You can send SMS in form of 1234 Y3 REG 25 to command the
device to maintain temperature to 25°C. The range of regulation is between 0°C
and +55°C. Regulation can be canceled by SMS with command 1234 Y3 OFF. By
default the regulation of OUTPUT 3 depends on temperature sensor connected to
analog INPUT T5 (OUTPUT 4 depends on INPUT T6).
8. A default factory setting of the
1234 FACTORY. Your setting can be then restored from backup configuration of
SeaConfigurator program.
4
GSM rele
or
4. Technical specifications
Parameter
Width
Dimensions Height
Depth
AC
Power Voltage
*1)
supply
Current
9
Digital inputs Voltage
Current
8
Voltage
Digital
outputs
Current
7
Analog inputs
5
Temperature
Storage
without supply
Temperature
6
Operational
4
GSM rele
Use - DIN inside the rack with IP44 or better!
*1)
Use breaker max. 10 A before
2
1 mm .
4
*2) GSM rele
The
24 hours (due to internal accumulator).
5. Hardware
The front panel of the
contains a set of status indicating LED
diodes located, pushbuttons for local
control of outputs, connectors for
connecting power supply, input signals,
output signals
sensors.
5.1 Connectors
4
GSM rele
enables
external digital inputs, 2 external digital
outputs and 2 external temperature
sensors GSM-C-T2 with temperature
range from -30°C to +55°C.
The line length of a connected external
temperature sensor is not limited but
the wire has a certain resistance which
influences the measured temperature (16
The recommended type of relay for connection of more appliances is GSM-RELE-OUT.
When using the GSM rele
4
(close to
output 3 and COM directly with a pushbutton of the gate control.
Read Technical specifications before connecting external devices! Don't overload
inputs and outputs.
Examples of connection of
5.2 Pushbuttons
GSM rele 4
The has two pushbuttons for local control of outputs. Every press of the
pushbutton changes the state of the output.
. This user can also control OUTPUT 4 by "ringing" on the device.
4
(with default factory setting). The device hangs up the call
4
GSM rele
can be recovered by an SMS in form
Symbol MIN. TYP.
Š
V
H
V 180 230
INPUT1, INPUT2
V 3
IN
I 3,5
IN
OUTPUT3, OUTPUT4 - Semiconductor switch OPTO-MOS
V 5 230
OUT
I
OUT
2 x temperature sensor GSM-C-T2, Accuracy in range 0 to 30°C ... 1°C
- -30
tA -20
4
GSM rele . For power supply 230V
has to be connected to 230V power supply every 3 months for
AC
1 2
4
GSM rele
Y3
GSM
ANT.
and temperature
3
GSM rele
1
to connect 2
X1 X2 4V
1 2 3 4 5 6
means 1 °C).
4
for a gate control by a phone ring, it's possible to connect
GSM rele 4
are placed later in this text.
MAX. Unit
71 mm
90 mm
58 mm
250 V AC
11 30 mA
12 30 V DC
mA DC
260 V AC
(400) (V DC)
90 mA AC
(120) (mA DC)
+55 °C
3 *2) Months
+45 °C
!
use lines min.
AC
N L1
1 2
1 2
Y4 230 V
AC
SIM,
uSD
EXT
4
POWER
ERROR
4
ALARM
2
USB
GSM
GND T5 T6
1 2 3 4
Page #1 of 5