Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Banner MIGHTYLAM 2700
Summary of Contents for Banner MIGHTYLAM 2700
- Page 1 OPERATING INSTRUCTIONS MIGHTYLAM 2700 ROLL LAMINATOR...
-
Page 2: Table Of Contents
TABLE OF CONTENTS Safety Messages and Electrical Safeguards ...3 - 4 Introduction ... Laminator Features ...5 Specifications ...5 Intial Set-up ...6 Operating Instructions…………………………………………7 - 8 Operation ... Loading Laminating Film ...8 Threading Laminating Film ...8 - 9 Adjusting Mandrel/Film Tension...10 Heat Shoe Temperature ...10... -
Page 3: Safety Messages And Electrical Safeguards
IMPORTANT SAFETY MESSAGES AND ELECTRICAL SAFEGUARDS For your protection, do not connect the laminator to electrical power or attempt to operate it until you read these instructions completely. Keep these instructions in a convenient location for future reference. This instruction manual and labels affixed to the laminator are important safety messages. Read these messages carefully. - Page 4 If the below conditions exist do not attempt to service or repair the laminator yourself. Unplug the laminator from the electrical outlet and contact an authorized service representative. • When the power supply cord or plug is damaged or frayed.
-
Page 5: Introduction
Congratulations on your purchase of the MightyLam 2700 Roll Laminator. This unit is designed to provide years of trouble-free service. The MightyLam 2700 will accept rolls of laminating film up to 27” wide in all film thicknesses. Paper and card stock up to 1/16” (1.6mm) thick may be laminated without adjusting the rollers. Your MightyLam 2700 is preset at the factory for most applications so any adjustments should be minor. -
Page 6: Initial Setup
Before unpacking the unit, inspect the shipping container for signs of damage. Notify the carrier and your dealer immediately if any damage is noted. Components... Figure 1 below shows the location of the major components and controls of the MightyLam 2700. You should become familiar with these before operating the laminator. Figure 1... -
Page 7: Operating Instructions
OPERATING INSTRUCTIONS Heat Control Your new MightyLam 2700 has digital heat controllers for each heat shoe. Users can easily adjust the set temperature for each heat shoe individually to achieve the best quality lamination. Both controllers have been calibrated to accurately display the heat shoe temperature in the laminating range. -
Page 8: Operation
These instructions apply to poly-in film rolls (shiny side out, dull side in). 1. For the top supply roll place the mandrel ends into the slots in the top of the laminator. If you are facing the front of the laminator the film should unwind toward you from the bottom of the roll as in figure below. - Page 9 Push the cardboard and film into the laminating rollers. See figure 5. Watch cardboard pass through the back (pull) rollers to avoid a wrap-around. 7. When the feed card has completely exited the pull rollers at the rear of the laminator turn the motor switch off. 8. Replace the feed table.
-
Page 10: Adjusting Mandrel/Film Tension
Adjusting Slitter Blades The slitter (figure 8) may be set to trim the web to the desired width as it exits the laminator. If an additional slitter blade is installed (optional), two pages (side-by-side) may be laminated and trimmed in a single operation. (As the web exits the unit, these pages may then be separated with the additional slitter blade). -
Page 11: Laminating
Caution! Do not allow the temperature to exceed 350°F as this could cause the laminating film to melt on the heat shoes. 2. Adjust the Paper Guide on the Feed Table so that the right edge of the item will enter the laminator at the desired position. -
Page 12: Coating Mount Board
Mounting & Laminating The MightyLam 2700 is capable of simultaneously mounting and laminating a print on up to 3/16” mount board. Preparing your print for mounting: 1. Peel back about 2” of release liner on your pre-coated mount board. - Page 13 Mounting your print: 1. Be sure all laminator parts (i.e. safety shield, feed table, etc.) are in their proper positions and the laminating film is loaded correctly on top and bottom mandrels. (See page 8-9 for film loading instructions). 2. Using the supplied allen wrench back out the four pressure adjustment screws 1 full turn for each 1/16” thickness of the board.
-
Page 14: Troubleshooting
TROUBLESHOOTING PROBLEM: Laminator is inoperative. Motor does not run, indicator lights are out. ACTION: Unit may be unplugged. Connect power supply. Ensure that your circuit breaker has not tripped. Fuse may have blown. Replace 15 amp power fuse. PROBLEM: Laminating film and item being laminated move through laminator erratically. -
Page 15: Maintenance
MAINTENANCE This section contains instructions for cleaning and maintaining your laminator. These procedures should be preformed at regular intervals to help ensure the trouble-free operation of your laminator. Cleaning the Heat Shoes and Laminating Rollers... The heat shoes and laminating rollers should be cleaned of any residual adhesive whenever the film does not pass smoothly over their surfaces. -
Page 16: Warranty & Return Policy
WARRANTY AND RETURN POLICY Warranty Your laminator is warranted to be free of defects in material and workmanship for a period of 1 year from the original purchase date. In the event of a defect in material or workmanship, the manufacturer or its authorized dealer, will repair or replace (at their option) the laminator. -
Page 17: Parts List
PARTS LIST AND ILLUSTRATIONS This section contains reference drawings and a partial parts list to assist you when ordering parts for your laminator. Some of the descriptions may have been changed for clarification. Part Item Description 10333 BUSHING, SUPPLY MANDREL... - Page 18 BUSHING, ROLLER BOTTOM KNOB, MOTOR SPEED 11596 CONTROLLER, HEAT 11535 FEED TABLE GUIDE ASSEMBLY 1395 CORD, POWER 14-3 11544 DVD, ROLL LAMINATOR 1170 FEET, RUBBER, LARGE 1172 FUSE HOLDER, MOTOR FUSE 11540 FUSE HOLDER, POWER 11327 FUSE, MAIN POWER 15AMP...
Need help?
Do you have a question about the MIGHTYLAM 2700 and is the answer not in the manual?
Questions and answers