Advertisement
Installations/Connections
[1] Fix WV-Q185 (wall mount bracket) on a wall and attach the
cover of WV-Q186 (mount bracket) to the WV-Q185
①
Pass the cables from the wall to the WV-Q185.
WV-Q185
③
Adjust the length of the cables so that the cables
of approx. 300 mm {11-13/16 inches} come out
from the opening of the WV-Q185.
Note:
• Do not bundle the cables (Ethernet cable,
Nameplate
power cable, etc.) during installation.
Mounting of Ⓐ inner cover (accessory)
may become difficult. (The provided illus-
tration shows the Ethernet cable as a rep-
resentative image.)
①
Approx. 300 mm
②
Fix the WV-Q185 on a wall with M10 screws
Cover part of
{11-13/16 inches} from the
(locally procured) or four anchors (locally procured).
WV-Q186
opening of WV-Q185
Minimum pull-out strength: 823 N {185 lbf}/
per 1 pc.
* Refer to the operating instructions of WV-Q185
for further information on how to fix.
③
Attach the cover part of the WV-Q186 to the
WV-Q185, and then fix it with M6 hex socket
screws (provided with WV-Q185).
(A hex wrench for M6 is required.)
(Recommended tightening torque: 2.45 N·m
{1.81 lbf·ft})
* Fix the cover so that the nameplate of the
WV-Q186 comes in front of the WV-Q185.
Cables
Nameplate
④
After fixing the WV-Q186 on the WV-Q185, lay the cables as shown in the upper right illustration
and confirm that the ends of the cables reach the cable line inside the cover of the WV-Q186.
[4] Making connections
Applicable models:
Network Camera: WV-SFV631LT,
Attachment plate
WV-SFV631L, WV-SFV611L, WV-SFV531,
(accessory provided
WV-SFV311A, WV-SFV310A,
with the camera)
WV-S2531LTN, WV-S2531LN,
WV-S2511LN, WV-SFV481, WV-SW458
CCTV Camera: WV-CW634S,
WV-CW634SE, WV-CW634F,
WV-CW630S/G, WV-CW364SE,
WV-CW334SE
* WV-SFV481 is used as an example in the
right illustration.
Cable
①
Connect the cables passed through the
plate in section [3] with the cables from
the camera.
Camera
* For information on cable connection,
please refer to the relevant camera usage
instructions.
②
Apply waterproof treatment to the joints of the cables.
<When waterproof treatment is applied to RJ45 connector and other cables>
Adequate waterproof treatment is required for the cables when installing the camera with cables
exposed. The camera body is waterproof, but the cable ends are not waterproof. Be sure to use
the waterproof tape provided with the camera at the points where the cables are connected and
apply waterproof treatment in the following procedure. Failure to observe this or use of a tape
other than the provided waterproof tape (such as a vinyl tape) may cause water leakage resulting
in malfunction.
Separately apply waterproof treatment to the network cable and other cables as shown in the
illustration below.
<LAN cable>
<Alarm input/output cable, power cable, micro-
phone/line input cable, audio output cable>
Wind the tape in a half-
Wind the tape in a
overlapping manner.
half-overlapping
manner.
[2] Fix the cable with the inner cover of WV-Q186
①
Wire the cables as shown below.
②
Fix Ⓐ inner cover (accessory) using Ⓑ screw
(M3: accessory).
(Recommended tightening torque: 0.78 N·m
{0.58 lbf·ft})
Ⓐ Inner cover
(accessory)
②
Ⓑ Screw (M3: accessory) ×3
M10 screws
(Recommended tightening torque: 0.78 N·m {0.58 lbf·ft})
[3] Attach the attachment plate to the cover part of the WV-Q186
Cover part of
The following installation instructions take
WV-Q186
WV-SFV481 as an example for illustration.
Front
direction of
①
Prepare the attachment plate (provided
WV-Q185
with the camera) and the fixing screws for
(wall mount
attachment plate (provided with the cam-
bracket)
era: M4 × 8 mm {5/16 inches}).
②
Pass the cables through the attachment
plate.
③
Align the "⇧TOP" mark on the attachment
plate with the front of WV-Q185 (wall
mount bracket).
④
Fix the attachment plate to the cover part
④
of the WV-Q186 with the fixing screws for
Cable line
attachment plate.
③
(Recommended tightening torque:
0.78 N·m {0.58 lbf·ft})
"⇧TOP" mark
Attachment plate
(accessory provided
with the camera)
* The upper right illustration is provided as an example of attaching the attachment plate for a camera
model having three attachment mounting screws.
IMPORTANT:
• Also waterproof the 2P power cable (provided with the camera), 4P alarm cable (provided
with the camera), and external connections in the same way.
• Stretch the tape by approx. twice (see the illustration
at right) and wind it around the cable. Insufficient
tape stretch causes insufficient waterproofing.
• Waterproof grade (JIS IP66 or equivalent) is
applied to this product only when it is installed
correctly and also an appropriate waterproof
treatment is applied.
The inner side of WV-Q186 (mount bracket) is
not waterproofed.
• When a LAN cable cover is provided with the
camera in the package, attach the LAN cable
cover to the cable as shown in the illustration and
fix it by sliding to the direction indicated by the
arrow. The connector of the LAN cable used with
this camera must meet the following restrictions.
Max. 16 mm
Max. 14 mm
{5/8 inches}
{9/16 inches}
<If RJ45 waterproof connector is used>
Connect an Ethernet cable (category 5e or better, straight) to RJ45 plug (locally procured).
(For details in the installation of RJ45 plug, please
refer to the Installation Guide of each camera.)
RJ45
RJ45 plug
a) Insert the RJ45 plug (locally procured) into the
waterproof
(locally
RJ45 waterproof jack connected to the camera.
jack
procured)
b) Connect the RJ45 waterproof connector cover
(provided with the camera) to the RJ45 water-
proof jack and then rotate the RJ45 waterproof
connector cover until the "⇦" marks align.
c) Connect the RJ45 waterproof connector cap
(provided with the camera) to the RJ45 water-
proof connector cover and rotate the RJ45 water-
proof connector cap until there is no gap between
it and the RJ45 waterproof connector cover.
IMPORTANT:
• If the procedure for the RJ45 waterproof connector (provided with the camera) part is not correctly followed, the waterproofing
may be compromised. Do not install the camera where the RJ45 waterproof connector is exposed to constant rain or moisture.
• When you remove the RJ45 waterproof connector, be sure to follow the reverse order of the connecting
procedures. (The RJ45 waterproof jack may be damaged when you try to remove the RJ45 waterproof
connector cover with its "⇦" mark matching "▶" mark of the RJ45 waterproof jack.)
[5] Fix the camera to the attachment plate
①
After connecting the cables to the camera, align the OPEN mark at the side of the camera enclo-
sure to the claw of the attachment plate (provided with the camera). Then, insert the attachment
mounting screws (2 or 3 points) at the bottom of the camera into the holes of the attachment
plate.
After that, move the LOCK mark to the point where the claw of the attachment plate is located by
rotating the camera body clockwise by approx. 15° to fix temporarily.
* Refer to the operating instructions of the connected camera for information on how to mount the
camera.
Claw of the attachment plate
(accessory provided with the camera)
<Example of mounting WV-SFV481>
IMPORTANT:
• When using WV-SFV481 or WV-SW458 with a SD memory card, insert the SD memory card to
the camera before mounting the camera onto the WV-Q186.
②
Fix the camera to the attachment plate.
②
For the mounting method of the camera, please
refer to the Installation Guide of each camera.
<For WV-SFV481>
④
1. Loosen two of the sub cover fixing screws
Fixing screw for
using the bit (provided with the camera) and
attachment plate ×4
remove the sub cover of the camera.
(accessory provided with
Then, tighten the camera fixing screw to fix the
the camera: M4 × 8 mm
{5/16 inches})
attachment plate and the camera.
(Recommended tightening torque: 0.78 N·m
{0.58 lbf·ft})
2. Attach the sub cover back to the original position
and fix with two of the sub cover fixing screws.
1
3
2
Stretch the tape to approx.
twice its length.
2x
The hook engages with
the connector terminal
RJ45
RJ45
waterproof
waterproof
connector cover
connector cap
(provided with
(provided with
the camera)
the camera)
<For WV-SW458>
Tighten the camera fixing screw located at the enclosure of the camera to fix the attachment plate
and the camera. (Recommended tightening torque: 0.78 N·m {0.58 lbf·ft})
<For cameras other than the above>
1. Loosen the fixing screws (3 or 4 screws)
of the enclosure using the bit and remove
the enclosure from the camera body.
Then, fix the camera with the camera fix-
ing screw.
(Recommended tightening torque:
0.78 N·m {0.58 lbf·ft})
Claw of the attachment plate
(accessory provided with the camera)
OPEN
OPEN
LOCK
LOCK
Camera
Camera
IMPORTANT:
• Enclosure is fixed at the installation auxiliary wire to the camera body, please do not remove the
<Example of mounting WV-SFV631L>
installation auxiliary wire.
Note:
• As for the enclosure fixing screw, there are three screws models and four screws models
depending on the camera model.
Refer to the operating instructions of the camera for further information.
2. Adjust images from the camera.
* Refer to the operating instructions of the camera for further information on how to adjust.
3. After completing the adjustment, attach the enclosure back to the original position and fix it with
the enclosure fixing screws (3 or 4 screws).
IMPORTANT: This caution shall be applied to all the cameras as described above.
• Be sure to tighten the camera fixing screw. Failure to observe this may cause camera trouble
due to camera falling.
(Recommended tightening torque: 0.78 N·m {0.58 lbf·ft})
Camera fixing screw
* The sub cover is omitted in the illustration.
Camera fixing
screw
* The enclosure is omitted in the illustration.
WV-SFV631L is used as an example in the
above illustration.
Advertisement
