1. Manuals
  2. Brands
  3. MTE Manuals
  4. Protection Device
  5. dV Sentry
  6. Installation manual

MTE dV Sentry Installation Manual

208v – 600v
Hide thumbs Also See for dV Sentry:
Table of Contents

Advertisement

Quick Links

Download this manual
dV Sentry
208V – 600V
INSTALLATION GUIDE
FORM: DVS-IG-E
REL. January 2018
REV. 003
© 2018 MTE Corporation
High Voltage! Only a qualified electrician can carry out the electrical
installation of this filter.
WARNING
❶
How to Install
❷
Startup/Troubleshooting
TM
Quick Reference
Pages 6 – 14
Pages 14 – 16

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the dV Sentry and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for MTE dV Sentry

Summary of Contents for MTE dV Sentry

  • Page 1 Sentry 208V – 600V INSTALLATION GUIDE FORM: DVS-IG-E REL. January 2018 REV. 003 © 2018 MTE Corporation High Voltage! Only a qualified electrician can carry out the electrical installation of this filter. WARNING Quick Reference Pages 6 – 14 ❶...

  • Page 2: Table Of Contents

    Sentry Installation Guide 208V – 600V TABLE OF CONTENTS 1. WARNINGS .............................. 3 ......................3 ARNINGS AND AUTIONS ..................... 3 RODUCT AFETY ABELING ....................4 ENERAL AFETY NSTRUCTIONS 2. INTRODUCTION ............................5 / ..................... 5 MTECORP SENTRY & R ....................

  • Page 3: Warnings

    Caution Product Safety Labeling The following labels are placed on the dV Sentry product: Label notes to installer to refer to instruction manual first before installing. High Voltage: surfaces on product can have high voltage which can cause injury.

  • Page 4: General Safety Instructions

    Modular filters must have reactor grounded through a 2”x2” area cleaned of paint and varnish on lower mounting bracket. Only spare parts obtained from MTE Corporation or an authorized MTE distributor can be used. Loose or improperly secured connections may damage or degrade filter performance.

  • Page 5: Introduction

    Sentry Installation Guide 208V – 600V 3. INTRODUCTION The purpose of the manual is to aid in the proper installation of the dV Sentry. For most current product information, including technical reference manual, please refer to website: www.mtecorp.com/dv-sentry/ This manual is intended for use by personnel experienced in the operation and maintenance of drives.

  • Page 6: How To Install

    The filter is designed for use with copper conductors with a minimum temperature rating of 75 degrees C. WARNING dV Sentry Filters are supplied in the following mechanical configurations: • Panel assemblies (3A-110A): Reactor and resistor are assembled on a panel and pre-wired together.

  • Page 7: Grounding

    Also be aware of minimum electrical clearances as defined by the appropriate system safety standard(s). Panel mounted dV Sentry Filters generate heat and should be positioned away from heat sensitive components. Ensure that proper panel orientation is maintained.

  • Page 8: Table 3-1: Over Temperature Switch

    12 VDC Resistive Loads 24 VDC Resistive Loads MTE highly recommends the use of the over temperature switch to prevent damage to the filter in rare instances of overheating from abnormal operating conditions Form: DVS-IG-E January 2018 REV. 003 mtecorp.com...

  • Page 9: Power Wiring Connection

    For all filters supplied in general purpose NEMA 1/2 & 3R cabinets, interconnection between the filter, its power source, and the drive is shown in Figure 4-3 (p12). Wire gauge range and terminal torque requirements for the dV Sentry and the resistor panel are shown in Table 4-2 (p13).

  • Page 10: Basic Schematic Diagrams

    Sentry Installation Guide 208V – 600V Basic Schematic Diagrams Figure 4-1: Basic Schematic Diagram Form: DVS-IG-E January 2018 REV. 003 mtecorp.com...

  • Page 11: Interconnection Diagram - Panel (3A-110A) And Enclosed (3A-600A)

    Sentry Installation Guide 208V – 600V Interconnection Diagram – Panel (3A-110A) and Enclosed (3A-600A) Figure 4-2: Panel Mounted and Enclosed Diagram mtecorp.com Form: DVS-IG-E January 2018 REV. 003...

  • Page 12: Interconnection Diagram - Modular (130A-600A)

    Sentry Installation Guide 208V – 600V Interconnection Diagram – Modular (130A-600A) Figure 4-3: Open Panel Diagram Form: DVS-IG-E January 2018 REV. 003 mtecorp.com...

  • Page 13: Torque Ratings

    RESPANEL-014 350kcmil(2x) Note: To prevent flexing or bending of the coil windings attached to dV Sentry filter, use appropriate strain relief to prevent stress on terminals. For flat copper terminal tabs, use two wrenches to tighten customer provided cable mounting hardware.

  • Page 14: Start Up

    Sentry Installation Guide 208V – 600V 5. START UP Startup Checklist Safety Precautions Before startup, observe the following warnings and instructions: Internal components of the filter are at line potential when the filter is connected to the drive. This voltage is extremely dangerous and may cause death or severe injury if you come in contact with it.

  • Page 15: Troubleshooting

    Sentry Installation Guide 208V – 600V 6. TROUBLESHOOTING INJURY OR DEATH MAY RESULT IF THE DRIVE SAFETY PRECAUTIONS ARE NOT OBSERVED. When properly installed, this equipment has been designed to provide maximum safety for operating personnel. However, hazardous voltages and elevated temperatures exist within the confines of the enclosure.

  • Page 16: Table 5-2: Troubleshooting Guide

    Multiple motor applications create complex loading and resonances with Possible cause: dV Sentry filter. Use only one dV Sentry filter per drive for a single motor. For multiple Solution: line applications, use a sine wave filter. Form: DVS-IG-E January 2018 REV. 003...

Table of Contents