Intake system for power stroke 6.0l turbo-diesel ford f250 2003; ford f250 2004; ford f250 2005; ford f250 2006; ford f250 2007; ford f350 2003; ford f350 2004; ford f350 2005; ford f350 2006; ford f350 2007; ford f450 2003; ford f450 2004; ford f450 2005
Do you have a question about the Ram-Air 42155 and is the answer not in the manual?
Questions and answers
Summary of Contents for banks Ram-Air 42155
Page 1
Owner’sManual with Installation Instructions Banks Ram-Air ® Intake System 2003-2007 Ford Power Stroke 6.0L Turbo-Diesel F250/F350/F450 Trucks THIS MANUAL IS FOR USE WITH SYSTEM 42155 & 42155-D...
Page 2
(P/N 61151-61152) (P/N 42750-42751) - 5” touchscreen interface that can Increases flow and provides more control the Banks Diesel Tuner and/or uniform air distribution to the SpeedBrake on the fly. engine for more available power at - Interchangable gauge display, read a given boost level.
Page 3
AutoMind Programmer (P/N 72522) (P/N 66110) Higher torque capacity over stock - Contains Banks tunes that boost - Lockup clutch is slip-resistant so your vehicles HP, Torque and MPG. transmission fluids stay cooler and - Displays a host of critical engine transmission life is prolonged.
Technical Service During installation, keep the Hotline. If you have any work area clean. If foreign debris questions relating to shipping is transferred to any Banks system or billing, please contact our component, clean it thoroughly before Customer Service Department. installing.
Page 5
Table of Contents Tools Required: • ⁄ ” drive ratchets with metric and Section 1 ..... . 6 standard sockets General Assembly •...
Page 7
SCREW, HEX HEAD, M8 X 1.25 X 50 91702 WASHER, LARGE, M8 STOCK GROMMET, FILTER MINDER STOCK FILTER MINDER STOCK MAF SENSOR STOCK INTAKE AIR TEMPERATURE SENSOR * These are stock components that will be reused with the Banks Ram-Air System.
Page 8
Make sure the engine has been OFF Intake Air Temperature (IAT) sensor. for several hours and cool. Both sensor types are installed in the You are about to install the Banks same location on the intake tube. Ram-Air Intake System. Read and Locate the MAF/IAT connector,...
Page 10
Remove the Torx (T-20), MAF Install the rubber grommet to the sensor screws using the supplied Banks Intake tube. Banks Torx tool bit. See Figure 6. In the engine compartment Carefully remove the MAF/IAT towards the front-top radiator brace, sensor and set aside.
Page 13
Place air filter hose clamp on air and bolt install and tighten the filter. Do not tighten the clamp. radiator/intercooler fastener. See Drop in Banks air filter with hose Figure 9. clamp and fit air filter lip onto intake Locate the Banks air filter housing...
Page 16
Figure 15 Place Banks cover onto air filter housing and secure lid using the supplied Phillips screws. Re-connect battery grounds. You have successfully completed the installation of the Banks Ram-Air Intake system. See Figure 15. Make sure to go over all hose clamps for tightness and connectors for a secure fit.
Page 17
Bank Ram-Air Oiled Air FIlter. OILING HINTS PRE-CLEANING Never use a Banks Ram-Air filter without oil (the filter will not stop Tap the element to dislodge any large the dirt without the oil). Use only air embedded dirt, then gently brush with filter oil.
Page 18
Follow all and air-filter oil. original installation instructions. REINSTALL DRY FILTER CLEANING Reinstall your Banks Ram-Air filter element with proper care. Make sure Clean every 50-100,000 miles on the element seats properly in the filter street-driven applications. Clean case.
Need help?
Do you have a question about the Ram-Air 42155 and is the answer not in the manual?
Questions and answers