NAD D 3045 Owner's Manual
  1. Manuals
  2. Brands
  3. NAD Manuals
  4. Amplifier
  5. D 3045
  6. Owner's manual

NAD D 3045 Owner's Manual

Hybrid digital dac amplifier
Hide thumbs Also See for D 3045:

Advertisement

Table of Contents

D 3045
®
Hybrid Digital DAC Amplifier
Owner's Manual

Advertisement

Table of Contents
loading

Related Manuals for NAD D 3045

Summary of Contents for NAD D 3045

  • Page 1 D 3045 ® Hybrid Digital DAC Amplifier Owner’s Manual...

  • Page 2: Important Safety Instructions

    IMPORTANT SAFETY INSTRUCTIONS 1. Read instructions - All the safety and operating instructions should be read NOTE TO CATV SYSTEM INSTALLER before the product is operated. This reminder is provided to call the CATV system installer’s attention to Section 2. Retain instructions - The safety and operating instructions should be retained 820-40 of the NEC which provides guidelines for proper grounding and, in particular, for future reference.
  • Page 3 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. The model and serial number of your new D 3045 are located on the back of the • Consult the dealer or an experienced radio TV technician for help.

  • Page 4: Getting Started

    QUICK SETUP This simple guide will help you get started with your D 3045. Place the D 3045 on a firm, level surface. Do not place the unit on a soft surface like a carpet. Make all the connections to your D 3045 with the unit unplugged from the mains power source.

  • Page 5: Identification Of Controls

    With the corresponding end of the mains power cord connected If a separate earth ground is necessary, use this terminal to to the AC mains input of the D 3045 and the plug connected to a ground your D 3045. The D 3045 can be connected to ground by mains power source, press o (Standby) to switch ON the D 3045 connecting a ground lead wire or similar to this terminal.
  • Page 6 With ARC connection established, D 3045 will output audio signal from TV. PRE OUT • The PRE/SUB OUT sockets make it possible to use the D 3045 as a IMPORTANT Ensure that the audio setting/format of ARC-connected devices to full range preamplifier to an external power amplifier.

  • Page 7: Amp 3 Remote Control

    IDENTIFICATION OF CONTROLS AMP 3 REMOTE CONTROL BASS AMP 3 1 ON: Power up unit from Standby mode to operating mode. OFF: Switch unit to Standby mode. 2 SOURCE d/f: Select through source input selections. 3 DIM: Toggle to select display brightness level – dim, bright or display turned off.

  • Page 8: Other Features

    Mac, Android or iOS users is also available from the paired Bluetooth device. www.foobar2000.org/download. BLUETOOTH AT TRANSMIT MODE D 3045 is open to connect or pair with other Source devices within the INSTALLING FOOBAR2000 FOR WINDOWS PLATFORM 1 Download the latest foobar2000 freeware from same Bluetooth network environment.
  • Page 9 OTHER FEATURES 12 Run foobar2000. Go to File $ Preferences $ Components. Confirm that “WASAPI output support” is already installed. 13 Go to “Playback” tab. Under “Replay/Gain”, ensure that both “Source Mode” and “Processing” are set to “None”. Select “Apply” to confirm the setting.
  • Page 10 OTHER FEATURES 15 The column header for sample-rate is not standard. Manually input 18 With D3045 as the default speaker, go to “Properties” and then sample rate as shown below. “Advanced”. Ensure that both options under “Exclusive Mode” are File $ Preferences $ Display $ Default User Interface $ Playlist selected.

  • Page 11: Auto Standby

    AUTO STANDBY TV CONNECT The D 3045 can be setup to automatically go to standby mode if there is TV Connect is a new software enabled feature that allows the D 3045 no user interface interaction and no active Source input within 30 minutes.
  • Page 12 OTHER FEATURES PERFORM IR LEARNING WITH TV REMOTE CONTROL Direct or point the D 3045 or TV remote control to the D 3045 front screen when performing below procedure. IR LEARNING PROCEDURE STEP** PROCEDURE D 3045 FRONT SCREEN DISPLAY Press and hold [MUTE] of AMP 3 remote LEARNING control to initiate IR learning mode.
  • Page 13 You may generate a template for proper placement of the feet. 184,5 NOTE 58,0 Ensure that with the feet installed, the D 3045 is stable, balanced and will not tip over. 185,8...

  • Page 14: Preamplifier Section

    <0.003 % at 120mW NAD SHALL NOT BE HELD LIABLE FOR ANY TECHNICAL OR USER INTERFACE DISCREPANCIES IN THIS MANUAL. THE D 3045 OWNER’S MANUAL MAY BE SUBJECT TO CHANGE WITHOUT NOTICE. Signal-to-Noise Ratio >90 dB (32 ohms load; A-weighted, ref.
  • Page 16 All rights reserved. NAD and the NAD logo are trademarks of NAD Electronics International, a division of Lenbrook Industries Limited. No part of this publication may be reproduced, stored or transmitted in any form without the written permission of NAD Electronics International.

Table of Contents