Advertisement
Quick Links
ShelterIt
™
10'x20'x8' Instant Shelter
INSTRUCTION MANUAL
# 71020
Parts Alert!
If you have a question or if there are missing parts, please call:
203-591-9032
Service@shelterit.com
or email
Monday-Friday 9:00am-5:00 p.m. EST
Missing parts will be sent to you via courier.
Visit ShelterIt.com for instructional video
DO NOT RETURN TO STORE!
Please read instructions fully before beginning assembly!
Visit Shelterit.com for installation Video
- 1 -
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for ShelterIt 71020
Summary of Contents for ShelterIt 71020
- Page 1 Service@shelterit.com or email Monday-Friday 9:00am-5:00 p.m. EST Missing parts will be sent to you via courier. Visit ShelterIt.com for instructional video DO NOT RETURN TO STORE! Please read instructions fully before beginning assembly! Visit Shelterit.com for installation Video - 1 -...
-
Page 2: Assembly Instructions
TABLE OF CONTENTS SAFETY CAUTIONS…….............3 PARTS LIST.................4 ASSEMBLY INSTRUCTIONS..........5-17 LIMITED WARRANTY............18 SAFETY and PRE-ASSEMBLY CAUTIONS READ PRIOR TO ASSEMBLY！ DO NOT ASSEMBLE OR DISASSEMBLE THE STRUCTURE ON A WINDY DAY. ONCE ASSEMBLED, IF HIGH WINDS ARE FORECASTED WE RECOMMEND YOU TO REMOVE THE COVER AND STORE UNTIL THE WINDY CONDITIONS HAVE PASSED. WARNING! The cover is made of 3-layer polyethylene. -
Page 3: Do Not Return This Product To The Store
Unpack and check the contents of the box. Make sure that you have all the parts described in the parts list shown hereafter. If parts are missing, please contact customer service: 203-591-9032. Missing parts will be sent courier to you. Do not return this product to the store! Visit Shelterit.com for installation Video - 3 -... -
Page 4: Parts List
PARTS LIST 10x20x8 P art # D escri p ti o n D raw i n g Q ty 10201 #1 4-way Peak Connector 10202 #2 3-way Peak Connector 10203 #3 Rafter Pole 10204 #4 Upright Pole1 10205 #5 Upright Pole2 and Top Cross Rail -s 10206 #6 Steel Foot Plate 10207 #7 Upright Pole 3 10208 #8 Side Connector... -
Page 5: Assembling The Frame
Assembling the Frame Visit Shelterit.com for installation Video Diagram A below represents the completed Frame Assembly once steps 1- 4 are completed. Note: 2 or more people are required for safe and accurate assembly. When assembling the frame HAND TIGHTEN the bolts for the cross rails where the Square are located in Diagram A. - Page 6 Failure to do so may cause bolts to tear the shelter’s cover. Step 2: Assembling the Roof Visit Shelterit.com for installation Video Diagram C. Look at B above for the part #s...
- Page 7 Hand tighten the nuts that are in the square box locations until after the doors are installed and then retighten. Connect the top part of the X Braces to the inside of the cross rail. Use a 3” bolt, washer and nut to connect the X braces. See Diagram G Visit Shelterit.com for installation Video - 7 -...
- Page 8 Step 4: Attaching the upright Legs There are four corner legs and 6 middle legs. Assemble the four corner leg tubes for first. Please refer to Diagram H. Installing the upright legs.This is accomplished by lifting the side of the shelter while the other side remains resting on the ground. Have your 2”...
- Page 9 Step 5. Installing the front and back door panel - 9 -...
- Page 10 - 10 -...
- Page 11 Visit Shelterit.com for installation Video INSTALLING THE FRONT AND BACK PANEL Starting from the peak, disconnect the Cross Rail from the 3-way top connector. Place exposed Rope at the top of the panel over the 3-way connector and under the cross pole as shown in Detail P above.. At each corner remove the Cross Rail and pull the door fabric around to the inside, placing the 3-way connector through the opening in the fabric as shown in Detail O.
- Page 12 This will tighten the doors to the frame. After making the door snug Detail 19 22 & 28 You can pull all around the inside corners of the door too even the door on the frame. The bottom of the door should be just above the eye hook and above the bottom corner leg This will insure the door will not rub on the ground and wear it out Detail 23.
- Page 13 Step 6. Installing the Covers Visit Shelterit.com for installation Video Installation Tip: Visually check all pipes of the frame to ensure they are fully inserted into the next pipe before installing cover. Pipes may separate during installation of end covers and prevent proper installation of the main cover Two people, each positioned approximately one-third into the center of the cover, carefully pull the cover over the frame.
- Page 14 Step 7: Installing Lower Cross Rails into the main cover The shelter cover is manufactured with heat-welded pipe pocket sleeves along the lower wall of each side (white color faces inside the shelter, Disconnect the lower cross rails and clamps and insert the cross rails in the pockets of the cover and reassemble the clamps to the frame hand tight.
- Page 15 - 15 -...
- Page 16 Visit Shelterit.com for installation Video Cover Tensioning Find the ropes coming out of the 4 corners of cover with the big loops with yellow……label You will see 2 red….. labels on the rope before the big loop Detail 20 & 24 Hook the cover rope that has the 2 red …...
- Page 17 Secure with wire cable and cable clamp as shown in Diagram M below. It is recommended that you buy permanent anchors for the shelter Visit Shelterit.com for permanent anchors and replacement parts PLEASE RE-READ ALL WARNINGS CONTAINED ON PAGE 3 OF THESE INSTRUCTIONS.
- Page 18 If you have a question or if there are missing parts, please call: 203-591-9032 Service@shelterit.com Or email Monday-Friday 9:00am-5:00 p.m. EST Missing parts will be sent to you via courier. Visit ShelterIt.com for instructional video DO NOT RETURN TO STORE! - 18 -...
Need help?
Do you have a question about the 71020 and is the answer not in the manual?
Questions and answers