Subscribe to Our Youtube Channel
Summary of Contents for Hioki DS 12DVF3
- Page 1 Cordless Driver Drill DS 9DVF3 • DS 12DVF3 Handling Instructions DS 12DVF3 Read through carefully and understand these instructions before use.
- Page 4 9.6V Rechargeable battery (For DS9DVF3) 12V Rechargeable battery (For DS12DVF3) Latch Pull out Insert Handle Push Insert Pilot lamp Hole for connecting the rechargeable battery Drill mark Clutch dial Triangle mark Weak Strong Line Shift knob Low speed High speed Ring Sleeve Tighten...
-
Page 5: General Operational Precautions
22. Always use the charger at the voltage specified GENERAL OPERATIONAL PRECAUTIONS on the nameplate. 23. Do not touch movable parts or accessories unless Keep work area clean. Cluttered areas and benches the battery has been removed. invite accidents. 24. Always charge the battery before use. Avoid dangerous environment. -
Page 6: Specifications
SPECIFICATIONS POWER TOOL Model DS9DVF3 DS12DVF3 No-load speed (Low/High) 0 – 280 / 0 – 840 / min 0 – 350 / 0 – 1050 / min Wood 21 mm 25 mm (Thickness 18mm) Drilling Metal Steel: 10 mm, Steel: 12 mm, (Thickness 1.6mm) Aluminum: 12 mm Aluminum: 15 mm... - Page 7 CAUTION battery and recharge it after it has cooled for a The UC9SD and UC12SD models are the while. exclusively designed charger. These cannot UC18YG charge batteries except the specified batteries. Before using the driver drill, charge the battery as It is possible to insert the batteries other than follows.
-
Page 8: Prior To Operation
dots. The tightening toque at position “1” is the Regarding electric discharge in case of new batteries, weakest and the torque is strongest at the highest etc. number (See Fig. 5). (3) Adjusting the tightening torque As the internal chemical substance of new batteries Rotate the clutch dial and line up the numbers “1, and batteries that have not been used for an 3, 5 ... - Page 9 4. The scope and suggestions for uses The usable scope for various types of work based on the mechanical structure of this unit is shown in Table 3. Table 3 Work Suggestions Wood Drilling Steel Use for drilling purpose. Aluminum Machine screw Use the bit or socket matching the screw diameter.
-
Page 10: Maintenance And Inspection
The hook can be installed on the right or left side and 3. Cleaning on the outside the angle can be adjusted in 5 steps between 0° and When the driver drill is stained, wipe with a soft 80°. dry cloth or a cloth moistened with soapy water. (1) Operating the hook Do not use chloric solvents, gasoline or paint thinner, (a) Pull out the hook toward you in the direction... - Page 11 HiKOKI HiKOKI HiKOKI HiKOKI HiKOKI HiKOKI HiKOKI HiKOKI HiKOKI HiKOKI HiKOKI...
- Page 13 HiKOKI...
- Page 14 HiKOKI...
- Page 16 HiKOKI...
- Page 17 HiKOKI HiKOKI HiKOKI HiKOKI HiKOKI HiKOKI HiKOKI HiKOKI HiKOKI HiKOKI HiKOKI HiKOKI HiKOKI HiKOKI...
- Page 19 Hitachi Koki Co., Ltd. Code No. C99135932 Code No. C99135932 Printed in China Printed in China...
Need help?
Do you have a question about the DS 12DVF3 and is the answer not in the manual?
Questions and answers