BACHMANN EUROPE Plc E-Z COMMAND DIGITAL COMMAND CONTROL SYSTEM User Manual

How E-Z Command Works
Command unit converts control knob and button inputs
into digital commands. It produces a digital signal and
Decoder with individual address on locomotive
responds to commands sent to it.
Decoder Outputs
- Power the motor in response to speed control
knob setting.
- Power lights and functions in response to
function buttons.
Wiring your Layout
For best results a DCC layout should have all track live. Details
of how to wire a layout can be found in various books on the
subject sold by model shops and book stores. However, a simple
solution for a train set or small layout is to put a staple in the
location, indicated on each point to carry power across the whole
layout.
Technical Notes
E-Z Command uses an unusual feature called 'SERVICE MODE PROGRAM LOCK' which allows decoders supporting the feature to be
programmed on a shared service track. Decoders not supporting this must be removed.
The decoder sold as 36-552 and fitted to Bachmann Branchline Junior locomotives and USA DCC On Board product lines have a
decoder supporting the feature.
Expand with E-Z Command Companion 36-510 and control a second train with your E-Z Command system.
• Never connect any other controller to the same section of track at
the same time as an E-Z COMMAND unit.Separate'power districts'
can be created using separate units but they must be double isolated
so that no train can bridge the join between sections.
• Never use an electric track cleaner alongside your E-Z COMMAND.
feeds the track.
• Decoder fitted locomotives will run on a DC controlled layout,
but don't use a feedback type DC controller.
• DC locomotives can be run with E-Z COMMAND as either
loco 10 or with the 36-560 DC controller as an 'add on'. As there
is a constant AC on the track we recommend that you do not
leave a DC locomotive stationary on the layout for extended
periods. A hum will be heard from locos not fitted with decoders
under DCC control. Any lights will all be lit and are not
controllable in DCC mode.
• When using a 36-560 DC controller with the E-Z
COMMAND the power is always connected through the 36-
560 DC controller as shown in the wiring diagram (REF 2).
Please direct technical support and warranty enquiries to : 01455 841756
Motion
Further information on DCC is also available on the website.
The product that this certificate is enclosed with has a Warranty for 12 months from the date of purchase against faulty materials or
workmanship subject to the following conditions. During this period such defects that occur will be repaired or defective parts replaced
free of charge
1. This Warranty applies only if the item was purchased from an authorised retailer of Bachmann Europe plc ('Bachmann') within the
European Union / EEA.ThisWarranty does not confer any rights other than those expressly set out above and does not cover any claims
for consequential loss or damage.TheWarranty is offered as an additional benefit and does not affect your statutory rights as a consumer.
2. For claims under thisWarranty,the product must be returned to Bachmann at the owners expense and risk directly to Bachmann Europe
plc, Moat Way, Barwell, Leicestershire LE9 8EY with evidence of the purchase date in form of retailer receipt /invoice accompanied by a
letter or Service Request form setting out the date and place of purchase, giving a brief explanation of the problem that has led to the claim.
It is essential that the claim reach the above address on or before the last day of this Warranty period. Late claims will not be considered.
3. The benefits of this Warranty are available only to the initial retail purchaser of the product for the time of ownership of the product
or expiry of the warranty period whichever should come first and are not in any way transferable to another
4. The Warranty does not extend to cover damage resulting from misuse or careless handling, accidental damage, wear and tear, or use
on a voltage supply other than that stamped on the product as appropriate.
5. The Warranty may be considered void if repairs have been attempted other than by Bachmann staff.
6. The Warranty is on the original product in its entirely and does not extend to individual components removed from the product. In
respect of train sets the warranty applies to motorised units and controllers only
7. In the event that Bachmann chooses to replace a product it will be with the nearest appropriate model of its choice.
8. Bachmann reserves the right to decline service to any model that has been fitted with a decoder after manufacture.
9. In the case of a Bachmann DCC Sound Decoder Fitted model a seal secures the decoder in place. Removal of this will void theWarranty.
10. Bachmann will not be held responsible for damage to or loss of an aftermarket decoder fitted to a model submitted for service
under the warranty
11. The fitting of a Bachmann decoder with a current Warranty shall not be deemed to change the position with regard to a product
that is otherwise outside its own Warranty. It may be necessary to change decoder settings during service
12. Bachmann's liability under this Warranty will in no case exceed the price paid for the product as originally manufactured
Bachmann Europe Plc, Moat Way, Barwell, Leicestershire, LE9 8EY. ENGLAND.
Do's and Dont's
• Only plug a Bachmann E-Z COMMAND device, or other device
specifically approved by Bachmann, into the X-Bus socket. Other
devices may have the same connector but are not necessarily
compatible.
• Bachmann E-Z COMMAND will work with any DCC standard
locomotive decoder. However, only 'third generation' decoders
support 'programming on the main' that is required for the
programming by E-Z COMMAND. Check with your decoder
instructions and remove any locomotive that does not have an
appropriate decoder from the track during programming.
• Only use the Bachmann supplied wall transformer with
E-Z COMMAND.
• Disconnect mains transformer from the wall when not using
E-Z COMMAND.
• No capacitor must be connected across the running tracks
(sometimes done for TV interference suppression). Some power
clips or feeds have these within them.
or via the website: www.bachmann.co.uk
BACHMANN EUROPE PLC: CONSUMER WARRANTY
www.bachmann.co.uk
Digital Command Train Control System
USER MANUAL
E-Z Command is able to operate a locomotive without a decoder (on ADDRESS 10) by adjusting the DCC signal - it
does not operate DC. Please exercise caution running a locomotive without a decoder. Do not leave stationary. Do not
use locomotives with small motors (eg. small OO or any N scale) without decoders, as damage to motors may result.