LOCKEY USA PD2 Installation Instructions

PD2
Keypad Electronic Deadbolt Installation Instructions
SPECIFICATIONS
Exterior Assembly
Latch Strike
Mounting Plate Interior Assembly
Mounting Screws Specifications
Wood screws Machine screws Mounting Plate screws
Qty. 4 Qty. 2 Qty. 2
BACKSET DETERMINATION
Backset is a distance from door edge to center of hole on door face.
Adjustable latch fits both backset of 2-3/8" (60 mm) and
2-3/4" (70 mm).
2-3/8" 60 mm ( )
or
2-3/4" 70 mm ( )
1. MARK THE DOOR WITH TEMPLATE
Select the height and backset as desired
on the door face ; use the TEMPLATE
as an indication to mark the center of
the circle on the door face and the
center of the door edge.
2. DRILL HOLES
Using the marks as a guide to drill a
hole Ø2-1/8" (54mm) through the door
face for the lockset, then a hole of
Ø1" (25.4mm) for latch.
2-1/8"
1"
(54 mm)
(25.4 mm)
IDENTIFY DOOR HANDING
Face the door from the outside, the door is left-handed if the
hinges are on the left side of the door, whereas the door is
right-handed if the hinges are on the right side of the door.
(a) (b)
Hinge
Keys
(Left Handed) (Right Handed)
Note : When installing make sure the door
opening side.
Spindle
Left handed door
install the spindle
(vertically)
Remarks : The latch will adjust from 2-3/8" (60 mm)
Please adjust to fit your door.
180°
3. INSTALL LATCH
a. Insert the latch and ensure it is
paralleled to the door face.
Mark the outline of the faceplate,
then take out the latch.
b. Chisel 1/8" 3mm (
outline to allow the faceplate to be
aligned with the door edge.
c. Insert the latch and tighten it with
screws.
Wood screws x 2
PD2 PD2
4. INSTALL THE EXTERIOR ASSEMBLY
a. Make sure the latch bolt is at unlocked
position.
b. Make sure you install the spindle inside
the lock body correctly.
If your door is LEFT-HANDED the spindle
should be VERTICAL in the latch.
If your door is RIGHT-HANDED the
spindle should be HORIZONTAL in the latch.
c. IC wire goes through the bottom of latch hole.
Hinge
Left handed door install
the spindle (vertically)
5. INSTALL THE MOUNTING PLATE
Right handed door
Before securing the mounting plate to the deadbolt with the
install the spindle
mounting screws make sure the IC wire fits cleanly through the
(horizontally)
corner of the plate.
to 2-3/4" (70 mm) .
IC wire
TEMPLATE
) deep along the
Fit here on door edge
45
1-3/4" 1-9/16" 1-3/8"
Mark Ø1" (25.4mm) hole at center of
door edge.
6. INSTALL THE INTERIOR ASSEMBLY
Insert 3 AAA alkaline batteries into the battery case. Pull the IC
cable from the side of the fixation plate and connect to the slot
on the interior assembly.
Spindle
Match the interior assembly, the turnpiece should be vertical, and
fasten the interior with screws.
IC wire
Right handed door install
the spindle (horizontally)
7. INSTALL STRIKE
Mounting Plate screws x2
For Backset 2-3/4" 70 mm ( )
For Backset 2-3/8" 60 mm ( )
40 35
PD2
Machine screws x 2
a. To identify the center of strike :
close the door, on the basis of the
faceplate mark horizontal center line
of strike. Ensure the center of faceplate
and the center of strike are aligned.
Use the mark as a guide outlines the
strike.
b. Chisel 5/64" (2mm) deep along the
strike outline to allow the strike to be
aligned with the doorframe.
c. Insert the strike and tighten it with
screws.
Wood screws x 2
Ø2-1/8" 54 mm ( )