Table of Contents
Advertisement
Quick Links
User Name:
Serial Number:
www.medifab.com
Neat Zeat
Installation &
User manual
IMPORTANT CONSUMER INFORMATION NOTICE: This manual
contains important instructions that must be passed on to the
user of this product. Please do not remove this manual before
delivery to the end user.
SUPPLIER: This manual must be given to the user of this product.
USER: Before using this product, read entire manual and save for
future reference.
User Manual for all Neat Zeats (product code begins with "3320-")
Manual: NeatZeat20140603
Advertisement
Table of Contents
Related Manuals for Medifab Neat Zeat
Summary of Contents for Medifab Neat Zeat
- Page 1 Neat Zeat Installation & User manual IMPORTANT CONSUMER INFORMATION NOTICE: This manual contains important instructions that must be passed on to the user of this product. Please do not remove this manual before delivery to the end user. SUPPLIER: This manual must be given to the user of this product.
- Page 2 Neat Zeat. Maximum User Weight: 75 kg. For users over 50 kg, it is recommended that a carer support the Neat Zeat during transfers. Options...
- Page 3 Maximum weight is 75 kgs (165 lb). • Avoid injuries to adults and older children from falls. • Do not use Neat Zeat as a step stool or ladder to climb up or reach elevated surfaces. • Do not allow adults to sit in Neat Zeat.
-
Page 4: Seat Height
WARNING Never adjust the Neat Zeat when the user is seated in the chair. Seat Height To raise or lower the seat height, remove the 4 t-nuts and the clamping plate on each side. -
Page 5: Seat Angle Adjustment
Installation & User Manual 10° Seat Angle Adjustment Remove the 4 t-nuts and the two clamping plate from each side. Replace the two clamping plate with four M6 coach bolts. Postion the seat at anagle, slide the M6 coach bolts through the seat rail into the wood sides. Refit the 4 t-nuts onto the m6 coach bolts and tighten. -
Page 6: Backrest Angle Adjustment
Neat Zeat Backrest Angle Adjustment Loosen the lower backrest bolt on both sides with the 4mm Allen Key, tilt the backrest to desired angle and retighten securely. Footplate Adjustment To adjust the footplate, simply follow the instruction procedure for Seat Height &... - Page 7 Installation & User Manual Laterals These can be adjusted in width. Loosen the two black wing knobs at the rear of the backrest slide in or out to the required position and retighten the knobs. To raise or lower, remove the knobs and adjust to the required height and refit the knobs. Pommel The pommel can be moved forward or back by simply loosening the bolt underneath with a 4mm Allen key and retightening once the desired position has...
-
Page 8: Backrest Assembly
Neat Zeat Assembling your Neat Zeat Your flat packed Neat Zeat will be packaged according to your ordered specifications. Some parts may be preassembled. Please follow the following instructions to assemble your Neat Zeat. Backrest Assembly Unpackage the backrest Note; Figure 2a shows these brackets being attached to get maximum seat depth, Figure 2b shows the brackets inverted to meet the minimum seat depth. - Page 9 Installation & User Manual Package 2 & 3 only Additional Backrest Assembly Steps Install the protractor supports using the following hardware: • 4 X 25mm Coach bolts, • 4 X M6 Washers, • 4 M6 Black Wing knobs Install the chest strap to the Velcro on backrest Install the backrest padding...
- Page 10 Neat Zeat Seat and Footplate Assembly Unpack the Seat plate Note: to achieve the minimum seat depth, bolt the seat to the rails using the first hole on each side. To achieve the maximum seat depth, use the second hole.
- Page 11 Installation & User Manual Zeat Frame Assembly Push into each brace the M6 X 12mm Cross Nuts Using M6 X50 mm connecting bolts, screw a side to the braces as shown Connect the other side to the braces Take your Zeat backrest assembly and bolt this into the frame at the top using 4 M6 X 35mm connecting bolts and two clamping plate.
- Page 12 Neat Zeat Zeat Frame Assembly (cont.) Take your seat assembly and slide the clamping plate through the seat rail into the wooden sides and secure with the 4 t nuts. Note; You can set the seat tilt at this stage – Please refer to the user manual Take your footplate assembly and slide the clamping plate through the footplate rail into the wooden sides and secure with the 4 t nuts.
-
Page 13: Tray Assembly
Installation & User Manual Tray Assembly Secure the tray mounting brackets to the wood sides using the two clamping plate and the 4 t-nuts. The tray heght can be adjusted by securing the tray mounting bracket to the lower holes. Secure the tray by tightening the black wing knobs on the tray. - Page 14 Neat Zeat Mobile Base Assembly Unpack the Mobile base • Insert a M6X20 Cross Nut into each hole in each foot of the Zeat sides Mount the chair onto the base and bolt the base to the chair using the following hardware: •...
-
Page 15: Maintenance And Cleaning
Customisations The Neat Zeat is very versatile and has been developed to meet the needs of a wide range of children with special needs. There are many special adaptions available - speak with your Medifab product consultant or local distributor regarding any customisations for your client. - Page 16 Your enthusiastic distributor is Medifab Ltd Phone +64 3 307 9790 +64 3 307 2820 Email info@medifab.co.nz ABN # 49 828 922 466 www.medifab.com...
Need help?
Do you have a question about the Neat Zeat and is the answer not in the manual?
Questions and answers