Subscribe to Our Youtube Channel
Summary of Contents for Aqua AQUA-STEAM GENERATOR 1
-
Page 1: Table Of Contents
COMMERCIAL STEAM GENERATOR Installation Instructions Please read all of the instructions carefully before commencing installation or using the facility. Contents Page 2 INTRODUCTION Page 2 TECHNICAL SPECIFICATION Page 4 TYPICAL INSTALLATION (FIGURE 1) Page 5 INSTALLATION & FITTING Page 7 AUTO FLUSHING GENERATOR (FIGURE 2) Page 9 OPERATING INSTRUCTIONS... -
Page 2: Introduction
INTRODUCTION AQUA STEAM 6-12Kw BKW and AQUA STEAM 18-24Kw BKW The AQUA-STEAM GENERATOR series have many unique features that make them superior to other steam generators in the market place. They have been designed to give maximum performance, easy installation, easy operation and low maintenance costs. - Page 3 A water softener is not normally required if regular cleaning is carried FLUSHING UNIQUE REDUCTION out or an Aqua-soft is fitted (Auto descaler) Note A 15mm waste pipe is SYSTEM necessary for discharging waste water that is near boiling point. Use a washing machine type stand pipe or other suitable drain.
-
Page 4: Typical Installation (Figure 1)
TYPICAL INSTALLATION (FIGURE 1) FIGURE 1 PLEASE NOTE THIS DIAGRAM IS NOT TO SCALE Page 4... -
Page 5: Installation & Fitting
STAGE TWO: - Water Supply Generally the water supplied from any regional water authority is of sufficient quality to use with the Aqua- Steam generator. Greater care is perhaps required if water is from a well or bore hole particularly if the iron content is high. - Page 6 STAGE SIX: - Fitting 12v Electronic Attendant Control9 This control must be fitted in an easily accessible dry place for the operation of the attendant. When the control is fitted to the wall then connect plugs coming from the control to the sockets on relay board inside left hand of generator box.
-
Page 7: Auto Flushing Generator (Figure 2)
AUTO FLUSHING GENERATOR (FIGURE 2) FIGURE 2 Page 7... - Page 8 Relay PCB - Domestic Board 3-9kW Safety Cut Out PCB Board Fuse Terminal Block For KW Change Terminal Block + KW Change Pins Set Of Probes- Aqua-Steam Generator Indicator Heater ON Indicator Water ON Indicator Power ON Indicator Generator State...
-
Page 9: Operating Instructions
OPERATING INSTRUCTIONS BJ6-12KW & BJ18-24KW OPERATING INSTRUCTIONS - AKW CONTROL ATTENDANT CONTROL (All connections to the control unit are 12V A.c. or D.C.) Unlock the clear lid with a screw driver. Then press the side next to the lock and the clear lid will open, press the control “ON”... - Page 10 COMPUTER LINK MANAGEMENT SYSTEM This link will allow you to switch the generator on or off from your computer but the timer switch must be in the off position. This function is only available by special order. TEMPERATURE ADJUST The digital thermostat displays the temperature at the sensor in the steam room, to display the set point press and hold the thermometer button.
-
Page 11: Descaling
DESCALING The steam generator manufacturer cannot accept responsibility for the quality of the water fed to the unit. Water quality varies from area to area and with the time of the year. Any warranty will be invalid if the generator is not kept free of water solids and scale. -
Page 12: Indicators
INDICATORS AKW INDICATORS CONTROL UNIT The two alternating green indicators at the bottom of the thermometer show that low voltage power is available at the control unit. When the control is turned on the steady indicators on the thermometer show the temperature. -
Page 13: Problem Solving Guide
PROBLEM SOLVING GUIDE SYMPTON PROBABLE CAUSE REMEDY 1. No Green light on control box Main power isolator switched off Ensure mains power is on and check for green light on generator 2. No steam from unit Control turned off Turn on at cubicle control 3. - Page 14 No responsibility can be accepted if the unit has been tampered with by unauthorized personnel. The most common cause for failure is poor water quality (i.e. impurities or scale) COPYRIGHT Aqua-Steam Generators Limited E & O E Page 14...
Need help?
Do you have a question about the AQUA-STEAM GENERATOR 1 and is the answer not in the manual?
Questions and answers
Hay, Paul from ruiru Kenya, can I get Room temperature sensor, for aqua steam mill 2000. 6-12BKW