Table of Contents
Advertisement
Quick Links
CABINET INSTALLATION INSTRUCTIONS
Thank you for choosing Royston cabinets for your store. As always, we appreciate your business and
are proud to have you as a customer.
IMPORTANT: These instructions provide general guidance for the installation of Royston-built cabinets.
Your unique project may require some particular steps not included here. Please call 800-334-1766 for
further assistance.
IMPORTANTE: Esta guía provee instrucciones generales para la instalar los gabi-netes Royston.
Algunos de los pasos para algún proyecto especial de instalación podrían no estar incluidos. Favor
llamar al 800-334-1766 para guía adicional.
RECOMMENDED TOOL LIST
1. Cordless Drill And Fastener Drive Bits
2. Level - 24" Minimum
3. Tape Measure
4. Rubber Mallet / Dead Blow Hammer
5. Pry Bar
6. Large Flat Head Screw Driver
7. Vise-Grips (Needle Nose)
8. Bar Clamps
9. Socket Set
10. Caulk Gun (Optional)
11. Safety Glasses
12. Gloves
Step 1.
CONFIRM that the carrier's bill of lading matches the
container and products unloaded from the delivery truck. Inspect the
outside of each container for any indication of potential concealed
damage. Carefully and clearly note any and all damage on the freight
bill before signing.
Paso 1.
CONFIRME que el reconocimiento del transportador
corresponde al contenedor y a los productos descargados del camión.
Una vez que el producto es retirado del camión, inspeccione la parte
1.
exterior de cada contenedor para identificar cualquier posible daño
oculto. Anote claramente todos los daños en el certificado de carga
antes de firmar.
Step 2.
REVIEW entire contents of envelope titled "Instructions
Enclosed". Keep this important information in a safe and secure place
as you will need to refer to it often during the installation process.
Paso 2.
REVISE el contenido total del sobre de "instrucciones
adjuntas". Mantenga esta información importante en un lugar seguro
ya que frecuentemente necesitará referirse a la misma durante la
instalación.
2.
LISTA RECOMENDADA DE HERRAMIENTAS:
1. Taladro inalámbrico y brocas de sujeción
2. Nivel – Mínimo de 24 pulgadas
3. Cinta de medir
4. Mazo de caucho / Martillo de golpe seco
5. Barra de palanca
6. Destornillador grande de cabeza plana
7. Agarraderas de prensa (Punta de aguja)
8. Abrazaderas de barra
9. Juego de alvéolos
10. Pistola de calafateo (Opcional)
11. Gafas de seguridad
12. Guantes
Advertisement
Table of Contents
Summary of Contents for Royston Cabinet
- Page 1 CABINET INSTALLATION INSTRUCTIONS Thank you for choosing Royston cabinets for your store. As always, we appreciate your business and are proud to have you as a customer. IMPORTANT: These instructions provide general guidance for the installation of Royston-built cabinets. Your unique project may require some particular steps not included here. Please call 800-334-1766 for further assistance.
- Page 2 If using stainless steel cabinet legs, thread clockwise into base corners until tight. Then, adjust leg to minimum height position. If using skirts, adjust legs to 6 1/2” (min) from the bottom of cabinet. Paso 7. Si está usando patas de gabinete de acero inoxidable, aterraje en el sentido de las manecillas del reloj en las esquinas de la base hasta que estén ajustadas.
- Page 3 Step 12. START cabinet leveling at floor high point. If no high point is evident, start at the end of a counter and at the wall (if there is one). Use leveling legs to level cabinets side to side and front to back.
- Page 4 Information in this document is the proprietary property of Royston LLC and is subject to change without notice. Reproduction in any manner without written permission of Royston LLC is absolutely forbidden. Royston LLC reserves the right to make changes in product design or detail and to discontinue any product or material without notice.
Need help?
Do you have a question about the Cabinet and is the answer not in the manual?
Questions and answers