Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for CHAMPS Jolly
Summary of Contents for CHAMPS Jolly
- Page 1 ’f( r“ w e “ . — ~ v 11.9.5.3 w “ W W W ” . . . A , r M ~ M I M . m — ' s 1 . \ { n o — m : ’4 ‘1 INSTRUCTION...
- Page 2 Contents ' . ' Introduction Package - Standard Contents About Electric Instant Shower Heater Site Requirements - Plumbing & Electrical Product Installation Plumbing Connections ShowerSet Installation ‘ Testing Plumbing Connections Electrical Connections Front Cover Mounting Testing Electrical Connections Usage of Electric Instant Shower Heater Operation Instructions Safety Precautions Electrical...
-
Page 3: Specifications
CHAMPS JoIIy/ Tiger Electric Instant Shower Heater is intended for heating water to the temperature suitable for a shower. Specifications: CHAMPS 220V] 230V Ingress protection rating IPX5 ’ Inlet & outlet water connection w 15mm (1/2" ESP) Minimum water row rate... - Page 4 MamUmt Shower set‘ Bracket Shower rod assembly Hop) Hung screws Shower Bracket sliding kit assembl y (Bottom) Washer Stopcock Instruction Luxunous Shower manual shower head hose (optional)
- Page 5 Electric InstantShower ‘ .‘ “ Electric InstantShower. Jolly Heater Unit ‘ Heater Unit (Frbntview) “(Rearview) Front cover Power selector knob Power indicator Water inlet Water outlet Base plate Cable clamp Terminalblock Power selector (PS) IO.“ Heating tank Thermostat ‘ Jolly...
- Page 6 Features: High quality Polymer tank: CHAMPS tanks are constructed with high quality durable polymer material for energy saving by minimizing heat loss. IPX5 Splash Proof Rating Designed and built with an IPX5 rating that protects the internal circuits from splashing water.
- Page 7 ectric instant ‘3 . heater y ’ ° Please check that 20—amp double Materials installation: pole heater switch with a minimum contact gap of at IeaSt 3mm in both Flexible hose and/or copper pipes poles is connected directly to the mains Hammer“...
-
Page 8: Plumbing Connections
Plumbing Connections Turn electricity supply. Turn water supply flush pipe clear debris impurities. Install mini valve mains water supply bath room ease maintenance and servicing. Mini valve Ettaglt'mr Take note electricity Unscrew bottom case water supply location and find a mounting screws suitable place for the heater unit. - Page 9 Hold the heater over the desired location and mark the mounting hole positions on the wall. Put the heater down and drill the holes as per marking. Insert wall plugs onto the - Align the heater and screw it tightly onto the wall Connect stopcock...
- Page 10 Install shower desired location with respect to heater main Connect shower hose unit heater outlet Note: Refer detailed installation procedure given separately in this booklet. Place shower head on shower holder (1 1). Connect hose shower head Completed plumbing connections will look like the above picture.
- Page 11 Testing Plumbing Connections Turn water supply check connections leakage. Rectify if there is any leakage found. Test adjust water flow rate approximately éllmin. Contact us for advice If water flow rate is too high or too low. Common errors to avoid for plumbing connections: open-close valve [stopcock at the outlet.
-
Page 12: Electrical Connections
Electrical Connections Proceed with electrical connections only after completing plumbing connections. Measure the cable length required to connect heater to the ceiling rose heater switch Cut the cable to the measured length with an allowance of 10cm. Connect stripped end of 3 wires ceiling rose [heater switch tightly... - Page 13 Clamp the cable using the cable clamp with screws Close the ceiling rose/heater switch with its cover and secure it with screw Cover conduit base with cover Complete rest electrical connections to be double pole " heater switch located outside the shower room...
- Page 14 Take the front cover and cut the U-shaped recess provided for guiding the power cable at the entry Mount front cover on to the base plate by guiding through the ribs Then secure casing using respective screws Slowly insert knob into respective spindle Completed...
- Page 15 Testing Electrical Connections ' Turn water supply fill tank with water, Turn power supply. Test water different power settings. Common errors to avoid in electrical connections: Do not cut heater casin insert cable. only slot provided in the top cover. Avoid loose electrical...
- Page 16 Operationing Instructions To turn on the shower heater: Turn heater switch. Turn water supply. Turn power selector knob LOW, MEDIUM HIGH. uni/x. «it. [LOW] [MEDIUM] [HIGH] To adjust shower temperature: Adjust power selector knob control power settings. (OFF) Cold setting. [LOW] —...
- Page 17 off stopcock to temporarily turn off water supply: Ihen you want to apply soap during shower, you can turn off the water supply emporarily by turning off the stopcock. careful when turning water supply to resume using shower heater. he first flush of water will be very hot.
-
Page 18: Safety Precautions
Safety Precautions shower heater water pressure less than bar. shower heater water flow rate lower than 3(lmin higher than 8!] min. Children. elderly, physically disabled individual difticulty in operating the shower heater safely. should not be allowed to use the shower heater without supervision. - Page 19 Terminal block 4. Heating element 1 Thermostat 5. Heating element 2 Microswitches 6. Indicator lights...
- Page 20 -nsg-gnqgspeiajedisegedl. Take one bracket, position it as above and open the end cover. Choose your preferred location with respect to the heater unit and mark the lowest point of bracket as shown Take bracket mark point exactly 15mm abovethe earlier marking...
- Page 21 Drill a hole at the second marking and insert the wall plug Hold bracket aligning to the earlier marking and fix it tightly using screw Insert shower vertically Into the opening of bracket Insert other bracket Into rod of top and push down as much possible...
- Page 22 Mark the top most point of the top bracket now - Take out both bracket and rod and mark a point exactly 15mm below the earlier marking, drill a hole and insert wall plug U-Shaped grip aligning to Rod Insert shower into bottom...
- Page 23 slider suitable height. Insert bracket move down Tighten grip using gripping screwing into wall knob tightly Put back the covers of the brackets...
- Page 24 CHAMPS...