Transition SM24T6DPA Web User Manual

24-port l2 gbe managed switch

Table of Contents

Quick Links

Download this manual

SM24T6DPA

24-Port L2 GbE Managed Switch

Web User Guide

33665 Rev. C

Table of Contents

Troubleshooting

Need help?

Do you have a question about the SM24T6DPA and is the answer not in the manual?

Questions and answers

Summary of Contents for Transition SM24T6DPA

Page 1 SM24T6DPA 24-Port L2 GbE Managed Switch Web User Guide 33665 Rev. C...
Page 2: Overview Of This Manual
Anyone using this product in such an application without express written consent of an officer of Transition Networks does so at their own risk, and agrees to fully indemnify Transition Networks for any damages that may result from such use or sale.
Page 3: Table Of Contents
Transition Networks SM24T6DPA Web User Guide Table of Contents SAFETY WARNINGS AND CAUTIONS ....................II INTRODUCTION ........................... 1 Overview of this Manual ......................1 Related Manuals .......................... 1 CHAPTER 1 OPERATION OF WEB-BASED MANAGEMENT ............. 6 CHAPTER 2 SYSTEM CONFIGURATION ..................7 2-1 System ...........................
Page 4 Transition Networks SM24T6DPA Web User Guide 2-9.1 Profile Table ..........................98 2-9.1.1 IPMC Profile Rule Settings Table ..................100 2-9.2 Address Entry......................... 101 2-10 MVR ..........................102 2-11 IPMC ..........................104 2-11.1 IGMP Snooping ........................104 2-11.1.1 Basic Configuration ...................... 104 2-11.1.2 VLAN Configuration ......................
Page 5 Transition Networks SM24T6DPA Web User Guide 3-1.4 Detailed Log ........................... 177 3-2 Green Ethernet ........................178 3-2.1 Port Power Savings ........................ 178 3-3 Ports ..........................179 3-3.1 Traffic Overview ........................179 3-3.2 QoS Statistics ......................... 180 3-3.3 QCL Status..........................181 3-3.4 Detailed Statistics ........................
Page 6 Transition Networks SM24T6DPA Web User Guide 3-11.4 Port Statistics ........................247 3-12 MAC Table ........................249 3-13 VLANs ..........................251 3-13.1 VLAN Membership....................... 251 3-13.2 VLAN Port ..........................253 3-14 VCL ..........................255 3-14.1 MAC-based VLAN ........................ 255 3-14.2 Protocol-based VLAN ......................256 3-15.2.1 Protocol to Group ......................
Page 7: Introduction
This manual tells you how to install and connect to your network system and configure and monitor the SM24T6DPA via the web by RJ-45 serial interface and Ethernet ports. Details of hardware and software functions are provided as well as examples of the web-based interface.
Page 8: Chapter 2 System Configuration
If two or more SM24T6DPA users are using administrator’s identity to manage the switch, only the administrator to do the last config setting will be able to configure the switch. NOTE: When you login to the SM24T6DPA via the Web UI, you can use IPv4 or IPv6 login to manage. NOTE:...
Page 9: System
Transition Networks SM24T6DPA Web User Guide System Configuration Chapter 2 This chapter describes the basic configuration tasks (System Information and Time, Account, IP, Syslog and NTP). System Here you can identify the system by configuring the contact information, name, and location of the switch, and enable or disable Bonjour Discovery.
Page 10: 2-1.2 Ip
Transition Networks SM24T6DPA Web User Guide 2-1.2 IP The IPv4 address for the switch can be obtained via DHCP Server for VLAN 1. To manually configure an address, you must change the switch's default settings to values that are compatible with your network. You may also need to establish a default gateway between the switch and management stations that exist on another network segment.
Page 11 Transition Networks SM24T6DPA Web User Guide • From this DHCP interface: Specify from which DHCP-enabled interface a provided DNS server should be preferred. DNS Proxy: When DNS proxy is enabled, system will relay DNS requests to the currently configured DNS server, and reply as a DNS resolver to the client devices on the network.
Page 12 Transition Networks SM24T6DPA Web User Guide If the IPv6 gateway address is not link-local, the switch ignores the next hop VLAN for the gateway. Buttons Add Interface: Click to add a new IP interface. A maximum of 8 interfaces is supported.
Page 13: 2-1.3 Ntp
Transition Networks SM24T6DPA Web User Guide 2-1.3 NTP NTP (Network Time Protocol) is used to sync the network time to Greenwich Mean Time (GMT). If you use NTP mode and select a built-in NTP time server or manually specify an NTP server as well as Time Zone, the switch will sync the time in a short after you click the Apply button.
Page 14: 2-1.4 Time
Clock Source: There are two modes for configuring how the Clock Source from. Select "Use Local Settings" : Clock Source from Local Time. Select "Use NTP Server" : Clock Source from NTP Server. 33665 Rev. A www.transition.com Page 11 of 290...
Page 15 Transition Networks SM24T6DPA Web User Guide System Date: Shows the current time of the system. The year limit is 2011 - 2037. Time Zone Configuration Time Zone: Lists various Time Zones worldwide. Select appropriate Time Zone from the drop down and click Apply to set.
Page 16: 2-1.5 System Log
Transition Networks SM24T6DPA Web User Guide 2-1.5 System Log Syslog is a standard for logging program messages. It allows separation of the software that generates messages from the system that stores them and the software that reports and analyzes them. It supports generalized informational, analysis and debugging messages. It is supported by a wide variety of devices and receivers across multiple platforms.
Page 17: Green Ethernet
Transition Networks SM24T6DPA Web User Guide 2-2 Green Ethernet EEE (Energy Efficient Ethernet) is a power saving option that reduces the power usage when there is low or no traffic utilization. EEE works by powering down circuits when there is no traffic. When a port gets data to be transmitted all circuits are powered up.
Page 18 Transition Networks SM24T6DPA Web User Guide EEE: Controls whether EEE (Energy Efficient Ethernet) is enabled for this switch port. For maximizing power savings, the circuit isn't started at once transmit data is ready for a port, but is instead queued until a burst of data is ready to be transmitted. This will give some traffic latency.
Page 19: Ports Configuration
2-3 Ports Configuration The section describes how to configure the Port detail parameters of the switch, enable or disable the switch ports, and Monitor the ports content or status. 2-3.1 Ports This page displays current port configurations. Ports can also be configured here. Web Interface To configure a Current Port Configuration in the web interface: 1.
Page 20 Transition Networks SM24T6DPA Web User Guide 1Gbps FDX - Forces the port in 1Gbps full duplex 2.5Gbps FDX - Forces the Serdes port in 2.5Gbps full duplex mode. SFP_Auto_AMS - Automatically determines the speed of the SFP. Note: There is no standardized way to do SFP auto detect, so here it is done by reading the SFP rom.
Page 21: 2-3.2 Ports Description
Transition Networks SM24T6DPA Web User Guide 2-3.2 Ports Description The section describes how to configure the Port’s alias or any descriptions for the Port Identity. It lets you enter an alphanumeric string describing the full name and version identification for the system’s hardware type, software version, and networking application.
Page 22: Dhcp
Transition Networks SM24T6DPA Web User Guide 2-4 DHCP The section describes how to configure the DHCP Snooping parameters of the switch. The DHCP Snooping can prevent attackers from adding their own DHCP servers to the network. 2-4.1 Server 2-4.1.1 Mode This page lets you configure Global mode and VLAN mode to enable/disable DHCP server per system and per VLAN.
Page 23 Transition Networks SM24T6DPA Web User Guide Parameter descriptions: Mode: Configure the operation mode per system. Possible modes are: Enabled: Enable DHCP server per system. Disabled: Disable DHCP server pre system. VLAN Range: Indicate the VLAN range in which DHCP server is enabled or disabled. The first VLAN ID must be smaller than or equal to the second VLAN ID.
Page 24: 2-4.1.2 Excluded Ip
Transition Networks SM24T6DPA Web User Guide 2-4.1.2 Excluded IP This page configures excluded IP addresses. The DHCP server will not allocate these excluded IP addresses to a DHCP client. Web Interface To configure DHCP server excluded IP in the web interface: 1.
Page 25: 2-4.1.3 Pool
Transition Networks SM24T6DPA Web User Guide 2-4.1.3 Pool This page manages DHCP pools. The DHCP server will allocate an IP address and deliver configuration parameters to DHCP client, according to the DHCP pool settings. Web Interface To configure DHCP server pool in the web interface: 1.
Page 26 Transition Networks SM24T6DPA Web User Guide Subnet Mask: Displays subnet mask of the DHCP address pool. If "-" is displayed, it means not defined. Lease Time: Displays lease time of the pool. Buttons Add New Pool : Click to add a new DHCP pool.
Page 27: 2-4.2 Snooping
Transition Networks SM24T6DPA Web User Guide 2-4.2 Snooping DHCP Snooping is used to block intruder on the untrusted ports of the switch device when it tries to intervene by injecting a bogus DHCP reply packet into a legitimate conversation between the DHCP client and server.
Page 28: 2-4.3 Relay
Transition Networks SM24T6DPA Web User Guide 2-4.3 Relay A DHCP relay agent is used to forward and to transfer DHCP messages between the clients and the server when they are not in the same subnet domain. It stores the incoming interface IP address in the GIADDR field of the DHCP packet.
Page 29 Transition Networks SM24T6DPA Web User Guide Buttons Apply – Click to save changes. Reset - Click to undo any changes made locally and revert to previously saved values. 33665 Rev. C www.transition.com/ Page 28 of 288...
Page 30: Security
Transition Networks SM24T6DPA Web User Guide 2-5 Security This section describes how to configure the Port Security settings of the Switch. You can use the Port Security feature to restrict input to an interface by limiting and identifying MAC addresses.
Page 31 Transition Networks SM24T6DPA Web User Guide By default, most group’s privilege level 5 has the read-only access and privilege level 10 has the read-write access. The system maintenance (software upload, factory defaults and etc.) need user privilege level 15. Generally, privilege level 15 can be used for an administrator account, privilege level 10 for a standard user account and privilege level 5 for a guest account.
Page 32: 2-5.1.2 Privilege Level
Transition Networks SM24T6DPA Web User Guide 2-5.1.2 Privilege Level This page provides an overview of the privilege levels. The switch provides user set Account, Aggregation, Diagnostics, EEE, GARP, GVRP,IP, IPMC Snooping, LACP, LLDP, LLDP MED, MAC Table, MRP, MVR, MVRP, Maintenance, Mirroring, Private VLANs, QoS, SMTP, SNMP, Security, Spanning Tree, System, Trap Event, VCL, VLAN,s Voice VLAN.
Page 33 Transition Networks SM24T6DPA Web User Guide Debug: Only present in CLI. Privilege Levels: Every group has an authorization Privilege level for the following sub groups: configuration read-only, configuration/execute read-write, status/statistics read-only, and status/statistics read-write (e.g., for clearing of statistics). User Privilege should be same as or greater than the authorization Privilege level to have the access to that group.
Page 34: 2-5.1.3 Authentication Method
Transition Networks SM24T6DPA Web User Guide 2-5.1.3 Authentication Method This page lets you configure a user that is authenticated when they log into the switch via one of the management client interfaces. You can use SSH (Secure SHell) to securely access the switch. SSH is a secure communication protocol that combines authentication and data encryption to provide secure encrypted communication.
Page 35: 2-5.1.4 Access Management
Transition Networks SM24T6DPA Web User Guide 2-5.1.4 Access Management This section describes how to configure access management of the switch, including HTTP/HTTPS, SNMP, and TELNET/SSH. You can manage the switch over an Ethernet LAN or over the Internet. Web Interface To configure an Access Management Configuration in the web interface: 1.
Page 36: 2-5.1.5 Snmp
Transition Networks SM24T6DPA Web User Guide 2-5.1.5 SNMP Any Network Management System (NMS) running the Simple Network Management Protocol (SNMP) can manage the Managed devices equipped with SNMP agent, provided that the Management Information Base (MIB) is installed correctly on the managed devices.
Page 37 Transition Networks SM24T6DPA Web User Guide Version: Indicates the SNMP supported version. Possible versions are: SNMP v1: Set SNMP supported version 1. SNMP v2c: Set SNMP supported version 2c. SNMP v3: Set SNMP supported version 3. Read Community: Indicates the community read access string to permit access to SNMP agent.
Page 38 Transition Networks SM24T6DPA Web User Guide 2-5.1.5.2 Trap Configure SNMP trap on this page. Global Settings Configure SNMP trap settings on this page. Web Interface To display the configure SNMP Trap Configuration in the web interface: 1. Click Configuration, Switch, SNMP, Trap.
Page 39 Transition Networks SM24T6DPA Web User Guide Enabled: Enable SNMP trap mode operation. Disabled: Disable SNMP trap mode operation. Version: Indicates the SNMP trap supported version. Possible versions are: SNMPv1: Set SNMP trap supported version 1. SNMPv2c: Set SNMP trap supported version 2c.
Page 40 Transition Networks SM24T6DPA Web User Guide 2-5.1.7.3 Communities The function is used to configure SNMPv3 communities. The Community and User Name are unique. To create a new community account, click the Add New Community button, and enter the account information then click Save. Up to four Groups are supported.
Page 41 Transition Networks SM24T6DPA Web User Guide 2-5.1.7.4 Users The function is used to configure SNMPv3 user. The Entry index key is UserName. To create a new User Name account, click the Add New User button, enter the user information, then click Save.
Page 42 Transition Networks SM24T6DPA Web User Guide first be ensured that the value is set correctly. Authentication Protocol : Indicates the authentication protocol that this entry should belong to. Possible authentication protocols are: None: No authentication protocol. MD5: An optional flag to indicate that this user uses MD5 authentication protocol.
Page 43 Transition Networks SM24T6DPA Web User Guide 2-5.1.7.5 Group The function is used to configure SNMPv3 group. The Entry index keys are Security Model and Security Name. To create a new group account, click the Add New Group button, and enter the group information then click Save.
Page 44 Transition Networks SM24T6DPA Web User Guide Security Name : A string identifying the security name that this entry should belong to. The allowed string length is 1 to 32, and the allowed content is ASCII characters from 33 to 126.
Page 45 Transition Networks SM24T6DPA Web User Guide 2-5.1.7.6 Views The function is used to configure SNMPv3 view. The Entry index keys are OID Subtree and View Name. To create a new view account, click the Add New View button, and enter the view information then click Save.
Page 46 Transition Networks SM24T6DPA Web User Guide 2-5.1.7.7 Access The page lets you configure SNMPv3 accesses. The Entry index key are Group Name, Security Model and Security level. To create a new access account, click the Add New Access button, and enter the access information then click Save. Max Group Number : 14...
Page 47 Transition Networks SM24T6DPA Web User Guide Security Level : Indicates the security model that this entry should belong to. Possible security models are: NoAuth, NoPriv: No authentication and no privacy. Auth, NoPriv: Authentication and no privacy. Auth, Priv: Authentication and privacy.
Page 48 Transition Networks SM24T6DPA Web User Guide 2-5.1.7.8 Trap Event Severity This page lets you view and configure current SNMP trap event severity parameters. Web Interface To display the configure Trap Event Severity in the web interface: 1. Click SNMP, Trap Event Severity.
Page 49 Transition Networks SM24T6DPA Web User Guide 2-5.1.8 RMON An RMON implementation typically operates in a client/server model. Monitoring devices contain RMON software agents that collect information and analyze packets. These probes act as servers and the Network Management applications that communicate with them act as clients.
Page 50 Transition Networks SM24T6DPA Web User Guide 2-5.1.8.2 History Configure RMON History table on this page. The entry index key is ID. Web Interface To display the configure RMON History in the web interface: 1. Click RMON, History. 2. Click Add New Entry.
Page 51 Transition Networks SM24T6DPA Web User Guide 2-5.1.8.3 Alarm Configure RMON Alarm table on this page. The entry index key is ID. Web Interface To display the configure RMON Alarm in the web interface: 1. Click RMON, Alarm. 2. Click Add New Entry.
Page 52 Transition Networks SM24T6DPA Web User Guide Sample Type: The method of sampling the selected variable and calculating the value to be compared against the thresholds, possible sample types are: Absolute: Get the sample directly. Delta: Calculate the difference between samples (default).
Page 53 Transition Networks SM24T6DPA Web User Guide 2-5.1.8.4 Event Configure RMON Event table on this page. The entry index key is ID. Web Interface To display the configure RMON Event in the web interface: 1. Click RMON, Event. 2. Click Add New Entry.
Page 54: 2-5.2 Network
Transition Networks SM24T6DPA Web User Guide 2-5.2 Network 2-5.2.1 Limit Control This section describes how to configure the Port Security settings of the switch. You can use the Port Security feature to restrict input to an interface by limiting and identifying MAC addresses.
Page 55 Transition Networks SM24T6DPA Web User Guide Parameter descriptions: System Configuration Mode : Indicates if Limit Control is globally enabled or disabled on the switch. If globally disabled, other modules may still use the underlying functionality, but limit checks and corresponding actions are disabled.
Page 56 Transition Networks SM24T6DPA Web User Guide State : This column shows the current state of the port as seen from the Limit Control's point of view. The state takes one of four values: Disabled: Limit Control is either globally disabled or disabled on the port.
Page 57: 2-5.2.2 Nas
Transition Networks SM24T6DPA Web User Guide 2-5.2.2 NAS The section describes how to configure the NAS parameters of the switch. The NAS server can be employed to connect users to a variety of resources including Internet access, conference calls, printing documents on shared printers, or by simply logging on to the Internet.
Page 58 Transition Networks SM24T6DPA Web User Guide Parameter descriptions: Mode : Indicates if NAS is globally enabled or disabled on the switch. If globally disabled, all ports are allowed forwarding of frames. Reauthentication Enabled : If checked, successfully authenticated supplicants/clients are reauthenticated after the interval specified by the Reauthentication Period.
Page 59 Transition Networks SM24T6DPA Web User Guide In MAC-based Auth. mode, the switch will ignore new frames coming from the client during the hold time. The Hold Time can be set to a number between 10 and 1000000 seconds. RADIUS-Assigned QoS Enabled : RADIUS-assigned QoS provides a means to centrally control the traffic class to which traffic coming from a successfully authenticated supplicant is assigned on the switch.
Page 60 Transition Networks SM24T6DPA Web User Guide (RFC3748). Frames sent between the switch and the RADIUS server are RADIUS packets. RADIUS packets also encapsulate EAP PDUs together with other attributes like the switch's IP address, name, and the supplicant's port number on the switch. EAP is very flexible, in that it allows for different authentication methods, like MD5-Challenge, PEAP, and TLS.
Page 61 Transition Networks SM24T6DPA Web User Guide merely a best-practices method adopted by the industry. In MAC-based authentication, users are called clients, and the switch acts as the supplicant on behalf of clients. The initial frame (any kind of frame) sent by a client is snooped by the switch, which in turn uses the client's MAC address as both username and password in the subsequent EAP exchange with the RADIUS server.
Page 62 Transition Networks SM24T6DPA Web User Guide configuration. RADIUS attributes used in identifying a VLAN ID: RFC2868 and RFC3580 form the basis for the attributes used in identifying a VLAN ID in an Access-Accept packet. The following criteria are used: • The Tunnel-Medium-Type, Tunnel-Type, and Tunnel-Private-Group-ID attributes must all be present at least once in the Access-Accept packet.
Page 63 Transition Networks SM24T6DPA Web User Guide Clicking these buttons will not cause settings changed on the page to take effect. Re-authenticate: Schedules a re-authentication whenever the quiet-period of the port runs out (EAPOL-based authentication). For MAC-based authentication, re-authentication will be attempted immediately.
Page 64: 2-5.2.3 Acl
SM24T6DPA Web User Guide 2-5.2.3 ACL The SM24T6DPA Access Control List (ACL) is used for packet filtering and also for selecting types of traffic to be analyzed, forwarded, or influenced in some way. The ACLs are divided into Ether Types (IPv4, ARP protocol, MAC and VLAN parameters, etc.). Here we will just go over the standard and extended access lists for TCP/IP.
Page 65 Transition Networks SM24T6DPA Web User Guide Disabled or a specific port number and it can't be set when action is permitted. The default value is "Disabled". Logging : Specify the logging operation of this port. The allowed values are: Enabled: Frames received on the port are stored in the System Log.
Page 66 Transition Networks SM24T6DPA Web User Guide 2-5.2.3.2 Rate Limiters The section describes how to configure the switch’s ACL Rate Limiter parameters. The Rate Limiter Level from 1 to 16 that allow user to set rate limiter value and units with pps or kbps.
Page 67 Transition Networks SM24T6DPA Web User Guide 2-5.2.3.3 Access Control List The section describes how to configure Access Control List rule. An Access Control List (ACL) is a sequential list of permit or deny conditions that apply to IP addresses, MAC addresses, or other more specific criteria.
Page 68 Transition Networks SM24T6DPA Web User Guide Parameter descriptions: Ingress Port : Indicates the ingress port of the ACE. Possible values are: Any: The ACE will match any ingress port. Policy: The ACE will match ingress ports with a specific policy.
Page 69 Transition Networks SM24T6DPA Web User Guide MAC Parameters: SMAC Filter : (Only displayed when the frame type is Ethernet Type or ARP.) Specify the source MAC filter for this ACE. Any: No SMAC filter is specified. (SMAC filter status is "don't-care".) Specific: If you want to filter a specific source MAC address with this ACE, choose this value.
Page 70: 2-5.2.4 Ip Source Guard
Transition Networks SM24T6DPA Web User Guide 2-5.2.4 IP Source Guard The section describes how to configure the IP Source Guard detail parameters of the switch. You can use the IP Source Guard configuration to enable or disable with the Port of the switch.
Page 71 Transition Networks SM24T6DPA Web User Guide 2-5.2.4.2 Static Table The section describes how to configure the Static IP Source Guard Table parameters of the switch. You could use the Static IP Source Guard Table configure to manage the entries. Web Interface To configure a Static IP Source Guard Table Configuration in the web interface: 1.
Page 72: 2-5.2.5 Arp Inspection
Transition Networks SM24T6DPA Web User Guide 2-5.2.5 ARP Inspection The section describes how to configure the ARP Inspection parameters of the switch. You can use the ARP Inspection configuration to manage the ARP table. 2-5.2.5.1 Configuration This section describes how to configure ARP Inspection setting including:...
Page 73 Transition Networks SM24T6DPA Web User Guide If you want to inspect the VLAN configuration, you have to enable the setting of "Check VLAN". The default setting of "Check VLAN" is disabled. When the setting of "Check VLAN" is disabled, the log type of ARP Inspection will refer to the port setting.
Page 74 Transition Networks SM24T6DPA Web User Guide 2-5.2.5.2 VLAN Mode Configuration Each page shows up to 9999 entries from the VLAN table, default being 20, selected through the "entries per page" input field. When first visited, the web page will show the first 20 entries from the beginning of the VLAN Table.
Page 75 Transition Networks SM24T6DPA Web User Guide Parameter descriptions: VLAN Mode Configuration : Specify ARP Inspection is enabled on which VLANs. First, you have to enable the port setting on Port mode configuration web page. Only when both Global Mode and Port Mode on a given port are enabled, ARP Inspection is enabled on this given port.
Page 76 Transition Networks SM24T6DPA Web User Guide 2-5.2.5.3 Static Table The section describes how to configure the Static ARP Inspection Table parameters of the switch. You can use the Static ARP Inspection Table configuration to manage the ARP entries. Web Interface To configure a Static ARP Inspection Table Configuration in the web interface: 1.
Page 77 Transition Networks SM24T6DPA Web User Guide 2-5.2.5.4 Dynamic Table Entries in the Dynamic ARP Inspection Table are shown on this page. The Dynamic ARP Inspection Table contains up to 1024 entries, and is sorted first by port, then by VLAN ID, then by MAC address, and then by IP address.
Page 78 Transition Networks SM24T6DPA Web User Guide Reset: Click to undo any changes made locally and revert to previously saved values. <<: Updates the table starting from the first entry in the Dynamic ARP Inspection Table. >>: Updates the table, starting with the entry after the last entry currently displayed 33665 Rev.
Page 79: 2-5.3 Aaa
Transition Networks SM24T6DPA Web User Guide 2-5.3 AAA This section shows how to use an AAA (Authentication, Authorization, and Accounting) server to provide access control to your network. The AAA server can use TACACS+ or RADIUS server to create and manage objects that contain settings for using AAA servers.
Page 80 Transition Networks SM24T6DPA Web User Guide it is considered to be dead. Deadtime: Deadtime, which can be set to a number between 0 to 1440 minutes, is the period during which the switch will not send new requests to a server that has failed to respond to a previous request.
Page 81: 2-5.3.2 Tacacs
Transition Networks SM24T6DPA Web User Guide 2-5.3.2 TACACS+ Web Interface To configure a Common Configuration of AAA, TACACS+ in the web interface: Figure 2-5.3.2: TACACS+ Authentication Server Configuration Parameter descriptions: Global Configuration: These setting are common for all configured TACACS+ servers.
Page 82 Transition Networks SM24T6DPA Web User Guide Hostname: The IP address or hostname of the TACACS+ server. Port: The TCP port to use on the TACACS+ server for authentication. Timeout: This optional setting overrides the global timeout value. Leaving it blank will use the global timeout value.
Page 83: Aggregation
Transition Networks SM24T6DPA Web User Guide 2-6 Aggregation The Aggregation is used to configure the settings of Link Aggregation. You can bundle more than one port with the same speed, full duplex and the same MAC to be a single logical port, thus the logical port aggregates the bandwidth of these ports.
Page 84 Transition Networks SM24T6DPA Web User Guide Parameter descriptions: Hash Code Contributors Source MAC Address : The Source MAC address can be used to calculate the destination port for the frame. Check to enable the use of the Source MAC address, or uncheck to disable.
Page 85: 2-6.2 Lacp
Transition Networks SM24T6DPA Web User Guide 2-6.2 LACP This page lets you view and configure current LACP port settings. An LACP trunk group with more than one ready member-port is a “real trunked” group. An LACP trunk group with one or no ready member-ports is not a “real”...
Page 86: Broadcast Storm Protection
Transition Networks SM24T6DPA Web User Guide 2-7 Broadcast Storm Protection This page lets you view and configure the current Broadcast Storm Protection settings. Parameter descriptions: Port: The switch port number of the port. Mode: Controls whether Broadcast Storm Protection is enabled on this switch port.
Page 87: Loop Protection
Transition Networks SM24T6DPA Web User Guide 2-8 Loop Protection Loop Protection is used to detect the presence of traffic. When switch receives packet’s (looping detection frame) MAC address the same as oneself from port, show Loop Protection happens. The port will be locked when it received the looping Protection frames. If you want to resume the locked port, find out the looping path, take off the looping path, then select the resume the locked port and click on “Resume”...
Page 88 Transition Networks SM24T6DPA Web User Guide Enable : Controls whether loop protection is enabled on this switch port. Action: Configures the action performed when a loop is detected on a port. Valid values are Shutdown Port, Shutdown Port and Log or Log Only.
Page 89: Spanning Tree
Transition Networks SM24T6DPA Web User Guide 2-9 Spanning Tree The Spanning Tree Protocol (STP) can be used to detect and disable network loops, and to provide backup links between switches, bridges or routers. This allows the switch to interact with other bridging devices (that is, an STP-compliant switch, bridge or router) in your network to ensure that only one route exists between any two stations on the network, and provide backup links which automatically take over when a primary link goes down.
Page 90 Transition Networks SM24T6DPA Web User Guide Figure 2-8.1: STP Bridge Configuration Parameter descriptions: Basic Settings Protocol Version : The STP protocol version setting. Valid values are STP, RSTP and MSTP. Bridge Priority : Controls the bridge priority. Lower numeric values have better priority.
Page 91 Transition Networks SM24T6DPA Web User Guide Advanced Settings Edge Port BPDU Filtering : Control whether a port explicitly configured as Edge will transmit and receive BPDUs. Edge Port BPDU Guard : Control whether a port explicitly configured as Edge will disable itself upon reception of a BPDU.
Page 92: 2-8.2 Msti Mapping
Transition Networks SM24T6DPA Web User Guide 2-8.2 MSTI Mapping When you implement a Spanning Tree protocol on the switch that the bridge instance. The CIST is not available for explicit mapping, as it will receive the VLANs not explicitly mapped. Due to the reason that you need to set the list of VLANs mapped to the MSTI.
Page 93 Transition Networks SM24T6DPA Web User Guide Parameter descriptions: Configuration Identification Configuration Name : The name identifying the VLAN to MSTI mapping. Bridges must share the name and revision (see below), as well as the VLAN-to-MSTI mapping configuration in order to share spanning trees for MSTI's (Intra-region). The name is at most 32 characters.
Page 94: 2-8.3 Msti Priorities
Transition Networks SM24T6DPA Web User Guide 2-8.3 MSTI Priorities When you implement a Spanning Tree protocol on the switch that the bridge instance. The CIST is the default instance which is always active. For controls the bridge priority. Lower numeric values have better priority. The bridge priority plus the MSTI instance number, concatenated with the 6-byte MAC address of the switch forms a Bridge Identifier.
Page 95: 2-8.4 Cist Ports
Transition Networks SM24T6DPA Web User Guide 2-8.4 CIST Ports When you implement an Spanning Tree protocol on the switch that the bridge instance, you must configure the CIST Ports. The section describes how to inspect the to view and configure the current STP CIST port configuration parameters.
Page 96 (state flag) : Operational flag describing whether the port is connecting directly to edge devices. (No Bridges attached). Transition to the forwarding state is faster for edge ports (having operEdge true) than for other ports. The value of this flag is based on AdminEdge and AutoEdge fields.
Page 97: 2-8.5 Msti Ports
Transition Networks SM24T6DPA Web User Guide 2-8.5 MSTI Ports The section describes it allows the user to inspect the current STP MSTI port configurations, and possibly change them as well. An MSTI port is a virtual port, which is instantiated separately for each active CIST (physical) port for each MSTI instance configured on and applicable to the port.
Page 98 Transition Networks SM24T6DPA Web User Guide Priority : Controls the port priority. This can be used to control priority of ports having identical port cost. (See above). Buttons Apply – Click to save changes. Reset- Click to undo any changes made locally and revert to previously saved values.
Page 99: Ipmc Profile
Transition Networks SM24T6DPA Web User Guide 2-9 IPMC Profile This page provides IPMC Profile related configurations. 2-9.1 Profile Table The IPMC profile is used to deploy the access control on IP multicast streams. You can create up to 64 Profiles with a maximum of 128 corresponding rules for each Profile.
Page 100 Transition Networks SM24T6DPA Web User Guide Parameter descriptions: Port : The switch port number of the corresponding STP CIST (and MSTI) port. Global Profile Mode: Enable/Disable the Global IPMC Profile. System starts to do filtering based on profile settings only when the global profile mode is enabled.
Page 101: 2-9.1.1 Ipmc Profile Rule Settings Table
Transition Networks SM24T6DPA Web User Guide 2-9.1.1 IPMC Profile Rule Settings Table This page provides the filtering rule settings for a specific IPMC profile. It displays the configured rule entries in precedence order. First rule entry has highest priority in lookup, while the last rule entry has lowest priority in lookup.
Page 102: 2-9.2 Address Entry
Transition Networks SM24T6DPA Web User Guide 2-9.2 Address Entry This page provides address range settings used in IPMC profile. The address entry is used to specify the address range that will be associated with IPMC Profile. It is allowed to create at maximum 128 address entries in the system.
Page 103: Mvr
Transition Networks SM24T6DPA Web User Guide 2-10 MVR The MVR feature enables multicast traffic forwarding on the Multicast VLAN. In a multicast television application, a PC or a television with a set-top box can receive the multicast stream. Multiple set-top boxes or PCs can be connected to one subscriber port, which is a switch port configured as an MVR receiver port.
Page 104 Transition Networks SM24T6DPA Web User Guide Caution: MVR source ports are not recommended to be overlapped with management VLAN ports. MVR Name : MVR Name is an optional attribute to indicate the name of the specific MVR VLAN. Maximum length of the MVR VLAN Name string is 32. MVR VLAN Name can only contain alphabets or numbers.
Page 105: Ipmc
Transition Networks SM24T6DPA Web User Guide 2-11 IPMC ICMP is an acronym for Internet Control Message Protocol. It is a protocol that generated the error response, diagnostic or routing purposes. ICMP messages generally contain information about routing difficulties or simple exchanges such as time-stamp or echo transactions.
Page 106 Transition Networks SM24T6DPA Web User Guide Parameter descriptions: Snooping Enabled: Enable the Global IGMP Snooping. Unregistered IPMCv4 Flooding enabled : Enable unregistered IPMCv4 traffic flooding. IGMP SSM Range : SSM (Source-Specific Multicast) Range allows the SSM-aware hosts and routers run the SSM service model for the groups in the address range. Format: (IP address/ sub mask).
Page 107: 2-11.1.2 Vlan Configuration
Transition Networks SM24T6DPA Web User Guide 2-11.1.2 VLAN Configuration The section describes the VLAN configuration setting process integrated with IGMP Snooping function. For Each setting page shows up to 99 entries from the VLAN table, default being 20, selected through the "entries per page" input field. When first visited, the web page will show the first 20 entries from the beginning of the VLAN Table.
Page 108 Transition Networks SM24T6DPA Web User Guide PRI : Priority of Interface indicates the IGMP control frame priority level generated by the system. These values can be used to prioritize different classes of traffic. The allowed range is 0 (best effort) to 7 (highest), default interface priority value is 0.
Page 109: 2-11.1.3 Port Filtering Profile
Transition Networks SM24T6DPA Web User Guide 2-11.1.3 Port Filtering Profile The section describes how to set the IGMP Port Group Filtering? With the IGMP filtering feature, a user can exert this type of control. In some network Application environments, as like the metropolitan or multiple-dwelling unit (MDU) installations, a user might want to control the multicast groups to which a user on a switch port can belong.
Page 110: 2-11.2 Mld Snooping
Transition Networks SM24T6DPA Web User Guide 2-11.2 MLD Snooping A network node that acts as a source of IPv6 multicast traffic is only an indirect participant in MLD snooping—it just provides multicast traffic, and MLD doesn’t interact with it. (Note, however, that in an application like desktop conferencing a network node may act as both a source and an MLD host;...
Page 111 Transition Networks SM24T6DPA Web User Guide Figure 2-11.2.1: MLD Snooping Configuration Parameter descriptions: Snooping Enabled : Enable the Global MLD Snooping. Unregistered IPMCv6 Flooding enabled : Enable unregistered IPMCv6 traffic flooding. The flooding control takes effect only when MLD Snooping is enabled. When MLD Snooping is disabled, unregistered IPMCv6 traffic flooding is always active in spite of this setting.
Page 112: 2-11.2.2 Vlan Configuration
Transition Networks SM24T6DPA Web User Guide 2-11.2.2 VLAN Configuration When MLD snooping is enabled on a VLAN, the switch acts to minimize unnecessary multicast traffic. If the switch receives multicast traffic destined for a given multicast address, it forwards that traffic only to ports on the VLAN that have MLD hosts for that address. It drops that traffic for ports on the VLAN that have no MLD hosts The >>| button will use the last entry of the currently displayed entry as a basis for the next...
Page 113 Transition Networks SM24T6DPA Web User Guide QRI : Query Response Interval. The Max Response Time used to calculate the Max Resp Code inserted into the periodic General Queries. The allowed range is 0 to 31744 in tenths of seconds; default query response interval is 100 in tenths of seconds (10 seconds).
Page 114: 2-11.2.3 Port Group Filtering
Transition Networks SM24T6DPA Web User Guide 2-11.2.3 Port Group Filtering The section describes that you could to set the Port Group Filtering in the MLD Snooping function. On the UI that you could add new filtering group and safety policy.
Page 115: Lldp
Transition Networks SM24T6DPA Web User Guide 2-12 LLDP The switch supports the LLDP. For current information on your switch model, The Link Layer Discovery Protocol (LLDP) provides a standards-based method for enabling switches to advertise themselves to adjacent devices and to learn about adjacent LLDP devices. The Link...
Page 116 Transition Networks SM24T6DPA Web User Guide Parameter descriptions: LLDP Parameters Tx Interval : The switch periodically transmits LLDP frames to its neighbours for having the network discovery information up-to-date. The interval between each LLDP frame is determined by the Tx Interval value.
Page 117 Transition Networks SM24T6DPA Web User Guide Sys Descr : Optional TLV: When checked the "system description" is included in LLDP information transmitted. Sys Capa : Optional TLV: When checked the "system capability" is included in LLDP information transmitted. Mgmt Addr : Optional TLV: When checked the "management address" is included in LLDP information transmitted.
Page 118: 2-12.2 Lldp-Med Configuration
Transition Networks SM24T6DPA Web User Guide 2-12.2 LLDP-MED Configuration This page lets you configure LLDP-MED (applies to VoIP devices that support LLDP-MED). Media Endpoint Discovery is an enhancement of LLDP, known as LLDP-MED that provides the following facilities: • Auto-discovery of LAN policies (such as VLAN, Layer 2 Priority and Differentiated services (Diffserv) settings) enabling plug and play networking.
Page 119 Transition Networks SM24T6DPA Web User Guide Parameter descriptions: Fast start repeat count Rapid startup and Emergency Call Service Location Identification Discovery of endpoints is a critically important aspect of VoIP systems in general. In addition, it is best to advertise only those pieces of...
Page 120 Transition Networks SM24T6DPA Web User Guide associated with ground level at the main entrance. Map Datum : The Map Datum is used for the coordinates given in these options: WGS84: (Geographical 3D) - World Geodesic System 1984, CRS Code 4327, and Prime Meridian Name: Greenwich.
Page 121 Transition Networks SM24T6DPA Web User Guide Policies Network Policy Discovery enables the efficient discovery and diagnosis of mismatch issues with the VLAN configuration, along with the associated Layer 2 and Layer 3 attributes, which apply for a set of specific protocol applications on that port. Improper network policy configurations are a very significant issue in VoIP environments that frequently result in voice quality degradation or loss of service.
Page 122 Transition Networks SM24T6DPA Web User Guide Video applications relying on TCP with buffering would not be an intended use of this application type. 8. Video Signalling (conditional) - for use in network topologies that require a separate policy for the video signalling than for the video media.
Page 123: Mac Table
Transition Networks SM24T6DPA Web User Guide 2-13 MAC Table Switching of frames is based on the DMAC address contained in the frame. The switch builds up a table that maps MAC addresses to switch ports for knowing which ports the frames should go to (based upon the DMAC address in the frame).
Page 124 Transition Networks SM24T6DPA Web User Guide Parameter descriptions: Aging Configuration : By default, dynamic entries are removed from the MAC table after 300 seconds. This removal is also called aging. Configure aging time by entering a value here in seconds; for example. The allowed range is 10 - 1000000 seconds.
Page 125: Vlans
Transition Networks SM24T6DPA Web User Guide 2-14 VLANs This page lets you assign a specific VLAN for management purpose. The management VLAN is used to establish an IP connection to the switch from a workstation connected to a port in the VLAN.
Page 126 Transition Networks SM24T6DPA Web User Guide A port can be in one of three modes as described below. Whenever a particular mode is selected, the remaining fields in that row will be either grayed out or made changeable depending on the mode in question.
Page 127 Transition Networks SM24T6DPA Web User Guide whether or not ingress filtering is enabled. This is useful in scenarios where a cloud of intermediary switches must bridge VLANs that haven't been created. By configuring the ports that connect the cloud of switches as trunking ports, they can seamlessly carry those VLANs from one end to the other.
Page 128: Private Vlans
Transition Networks SM24T6DPA Web User Guide 2-15 Private VLANs In a private VLAN, communication between ports in that private VLAN is not permitted. A VLAN can be configured as a private VLAN. 2-15.1 VLAN Membership The VLAN membership configuration for the switch can be monitored and modified here. Up to 4096 VLANs are supported.
Page 129: 2-15.2 Port Isolation
Transition Networks SM24T6DPA Web User Guide 2-15.2 Port Isolation Port Isolation provides for an apparatus and method to isolate ports on layer 2 switches on the same VLAN to restrict traffic flow. The apparatus comprises a switch having said plurality of ports, each port configured as a protected port or a non-protected port.
Page 130: Vcl
Transition Networks SM24T6DPA Web User Guide 2-16 VCL 2-16.1 MAC-based VLAN MAC address-based VLAN decides the VLAN for forwarding an untagged frame based on the source MAC address of the frame. A common way of grouping VLAN members is by port, hence the name port-based VLAN.
Page 131 Transition Networks SM24T6DPA Web User Guide without any port members will be deleted when you click "Save". The Reset button can be used to undo the addition of new MAC-based VLANs. Buttons: Apply – Click to save changes. Reset- Click to undo any changes made locally and revert to previously saved values.
Page 132: 2-16.2 Protocol -Based Vlan
Transition Networks SM24T6DPA Web User Guide 2-16.2 Protocol -based VLAN This section describe Protocol -based VLAN, The Switch support Protocol include Ethernet LLC SNAP Protocol, The Logical Link Control (LLC) data communication protocol layer is the upper sub-layer of the Data Link Layer (which is itself layer 2, just above the Physical Layer) in the seven-layer OSI reference model.
Page 133 Transition Networks SM24T6DPA Web User Guide Below is the criteria for three different Frame Types: For Ethernet: Values in the text field when Ethernet is selected as a Frame Type is called etype. Valid values for etype ranges from 0x0600-0xffff For LLC: Valid value in this case is comprised of two different sub-values.
Page 134: 2-16.2.2 Group To Vlan
Transition Networks SM24T6DPA Web User Guide 2-16.2.2 Group to VLAN This section allows you to map an already configured Group Name to a VLAN for the switch. Web Interface To Display Group Name to VLAN mapping table configured in the web interface: Click Group Name VLAN configuration and add new entry.
Page 135: 2-16.3 Ip Subnet-Based Vlan
Transition Networks SM24T6DPA Web User Guide 2-16.3 IP Subnet-based VLAN The IP subnet-based VLAN entries can be configured here. This page allows for adding, updating and deleting IP subnet-based VLAN entries and assigning the entries to different ports. This page shows only static entries.
Page 136: Voice Vlan
Transition Networks SM24T6DPA Web User Guide 2-17 Voice VLAN Voice VLAN is VLAN configured specially for voice traffic. By adding the ports with voice devices attached to voice VLAN, we can perform QoS-related configuration for voice data, ensuring the transmission priority of voice traffic and voice quality.
Page 137 Transition Networks SM24T6DPA Web User Guide VLAN ID : Indicates the Voice VLAN ID. It should be a unique VLAN ID in the system and cannot equal each port PVID. It is a conflict in configuration if the value equals management VID, MVR VID, PVID etc.
Page 138: 2-17.2 Oui
Transition Networks SM24T6DPA Web User Guide 2-17.2 OUI The section describes to Configure VOICE VLAN OUI table. The maximum entry number is 16. Modifying the OUI table will restart auto detection of OUI process. Web Interface To configure Voice VLAN OUI Table in the web interface: Select “Add new entry”, “delete”...
Page 139: Qos
Transition Networks SM24T6DPA Web User Guide 2-18 QoS The switch supports four QoS queues per port with strict or weighted fair queuing scheduling. It supports QoS Control Lists (QCL) for advance programmable QoS classification, based on IEEE 802.1p, Ethertype, VID, IPv4/IPv6 DSCP and UDP/TCP ports and ranges.
Page 140 Transition Networks SM24T6DPA Web User Guide parentheses after the configured default CoS. DPL : Controls the default drop precedence level. All frames are classified to a drop precedence level. If the port is VLAN aware, the frame is tagged and Tag Class. is enabled, then the frame is classified to a DPL that is mapped from the PCP and DEI value in the tag.
Page 141: 2-18.2 Port Policing
Transition Networks SM24T6DPA Web User Guide 2-18.2 Port Policing This section provides an overview of f QoS Ingress Port Policers for all switch ports. Port Policing is useful in constraining traffic flows and marking frames above specific rates. Policing is primarily useful for data flows and voice or video flows because voice and video usually maintains a steady rate of traffic.
Page 142: 2-18.4 Port Schedulers
Transition Networks SM24T6DPA Web User Guide 2-18.4 Port Schedulers This section provides an overview of QoS Egress Port Schedulers for all switch ports. Web Interface To display the QoS Port Schedulers in the web interface: 1. Click Configuration, QoS, Port Schedulers 2.
Page 143 Transition Networks SM24T6DPA Web User Guide If you select the scheduler mode with weighted then the screen will change as shown. Parameter descriptions: Port : The logical port for the settings contained in the same row. Click on the port number in order to configure the schedulers.
Page 144 Transition Networks SM24T6DPA Web User Guide Port Shaper Rate : Controls the rate for the port shaper. The default value is 500. This value is restricted to 100-1000000 when the "Unit" is "kbps", and it is restricted to 1-13200 when the "Unit" is "Mbps".
Page 145: 2-18.5 Port Shaping
Transition Networks SM24T6DPA Web User Guide 2-18.5 Port Shaping This section provides an overview of QoS Egress Port Shapers for all switch ports. Web Interface To display the QoS Port Shapers in the web interface: 1. Click Configuration, QoS, Port Shapers 2.
Page 146 Transition Networks SM24T6DPA Web User Guide If you select the scheduler mode with weighted then the screen will change as the figure. Parameter descriptions: Port : The logical port for the settings contained in the same row. Click on the port number in order to configure the shapers.
Page 147 Transition Networks SM24T6DPA Web User Guide Port Shaper Enable : Controls whether the port shaper is enabled for this switch port. Port Shaper Rate : Controls the rate for the port shaper. The default value is 500. This value is restricted to 100-1000000 when the "Unit"...
Page 148: 2-18.6 Port Tag Remarking
Transition Networks SM24T6DPA Web User Guide 2-18.6 Port Tag Remarking The Section provides user to get an overview of QoS Egress Port Tag Remarking for all switch ports. Web Interface To display the QoS Port Tag Remarking in the web interface: 1.
Page 149 Transition Networks SM24T6DPA Web User Guide Parameter descriptions: Mode : Controls the tag remarking mode for this port. Classified: Use classified PCP/DEI values. Default: Use default PCP/DEI values. Mapped: Use mapped versions of QoS class and DP level. PCP/DEI Configuration : Controls the default PCP and DEI values used when the mode is set to Default.
Page 150 Transition Networks SM24T6DPA Web User Guide Buttons: Apply – Click to save changes. Reset- Click to undo any changes made locally and revert to previously saved values. Cancel – Click to cancel the changes. 33665 Rev. C www.transition.com/ Page 149 of 288...
Page 151: 2-18.7 Port Dscp
Transition Networks SM24T6DPA Web User Guide 2-18.7 Port DSCP The section describes how to set the QoS Port DSCP configuration that lets you configure the basic QoS Port DSCP Configuration settings for all switch ports. Web Interface To configure the QoS Port DSCP parameters in the web interface: 1.
Page 152 Transition Networks SM24T6DPA Web User Guide Apply – Click to save changes. Reset- Click to undo any changes made locally and revert to previously saved values. Auto-refresh : To select the auto-refresh icon then the device will refresh the information automatically.
Page 153: 2-18.8 Dscp-Based Qos
Transition Networks SM24T6DPA Web User Guide 2-18.8 DSCP-Based QoS The section will teach user to configure the DSCP-Based QoS mode that This page allows you to configure the basic QoS DSCP based QoS Ingress Classification settings for all switches. Web Interface To configure the DSCP –Based QoS Ingress Classification parameters in the web...
Page 154: 2-18.9 Dscp Translation
Transition Networks SM24T6DPA Web User Guide 2-18.9 DSCP Translation The section describes the switch allows you to configure the basic QoS DSCP Translation settings for all switches. DSCP translation can be done in Ingress or Egress. Web Interface To configure the DSCP Translation parameters in the web interface: 1.
Page 155 Transition Networks SM24T6DPA Web User Guide There is one configurable parameter for the Egress side: Remap: Select the DSCP value from select menu to which you want to remap. DSCP value • ranges from 0 to 63. Buttons: Apply – Click to save changes.
Page 156: 2-18.10 Dscp Classification
Transition Networks SM24T6DPA Web User Guide 2-18.10 DSCP Classification This page lets you map a DSCP value to a QoS Class and DPL value. Web Interface To configure the DSCP Classification parameters in the web interface: 1. Click Configuration, QoS, DSCP Translation.
Page 157: 2-18.11 Qos Control List Configuration
Transition Networks SM24T6DPA Web User Guide 2-18.11 QoS Control List Configuration The section shows the QoS Control List (QCL), which is made up of the QCEs. Each row describes a QCE that is defined. The maximum number of QCEs is 256 on each switch.
Page 158 Transition Networks SM24T6DPA Web User Guide Broadcast: Match broadcast DMAC. <MAC>: Match specific DMAC. The default value is 'Any'. SMAC : Match specific source MAC address or 'Any'. If a port is configured to match on DMAC/DIP, this field indicates the DMAC.
Page 159 Transition Networks SM24T6DPA Web User Guide Key Parameters : Key configuration are described as below: Tag Value of Tag field can be 'Any', 'Untag' or 'Tag' VID Valid value of VLAN ID can be any value in the range 1-4095 or 'Any'; user can enter either a...
Page 160 Transition Networks SM24T6DPA Web User Guide Action Configuration : Class QoS Class: "class (0-7)", default- basic classification DP Valid DP Level can be (0-3)", default- basic classification DSCP Valid dscp value can be (0-63, BE, CS1-CS7, EF or AF11-AF43) Buttons: Apply –...
Page 161: 2-18.12 Storm Control
Transition Networks SM24T6DPA Web User Guide 2-18.12 Storm Control The section allows user to configure the Storm control for the switch. There is a unicast storm rate control, multicast storm rate control, and a broadcast storm rate control. These only affect flooded frames, i.e.
Page 162: Mirror
Transition Networks SM24T6DPA Web User Guide 2-19 Mirror You can mirror traffic from any source port to a target port for real-time analysis. You can then attach a logic analyzer or RMON probe to the target port and study the traffic crossing the source port in a completely unobtrusive manner.
Page 163 Transition Networks SM24T6DPA Web User Guide Mirror Port Configuration The following table is used for Rx and Tx enabling. Port : The logical port for the settings contained in the same row. Mode : Select mirror mode. Rx only Frames received on this port are mirrored on the mirror port. Frames transmitted are not mirrored.
Page 164: Upnp
Transition Networks SM24T6DPA Web User Guide 2-20 UPnP UPnP (Universal Plug and Play) goals of UPnP are to allow devices to connect seamlessly and to simplify the implementation of networks in the home (data sharing, communications, and entertainment) and in corporate environments for simplified installation of computer components.
Page 165: Gvrp
Transition Networks SM24T6DPA Web User Guide 2-21. GVRP The Generic Attribute Registration Protocol (GARP) provides a generic framework whereby devices in a bridged LAN, e.g. end stations and switches, can register and de-register attribute values, such as VLAN Identifiers, with each other. In doing so, the attributes are propagated to devices in the bridged LAN, and these devices form a ¡°reachability¡±...
Page 166 Transition Networks SM24T6DPA Web User Guide Enable GVRP globally :The GVRP feature is enabled by setting the check mark in the checkbox named Enable GVRP. GVRP protocol timers Join-time is a value in the range 1-20 in the units of centi seconds, i.e. in units of one hundredth of a second.
Page 167: 2-21.2 Port Config
Transition Networks SM24T6DPA Web User Guide 2-21.2 Port Config This page allows you to configure the basic GVRP Configuration settings for all switch ports. The settings relate to the currently selected unit, as reflected by the page header. Web Interface To configure the sFlow Agent in the web interface: 1.
Page 168: Sflow
Transition Networks SM24T6DPA Web User Guide 2-22. sFlow The sFlow Collector configuration for the can be monitored and modified here. switch The configuration is divided into two parts: Configuration of the sFlow receiver (a.k.a. sFlow collector) and configuration of per-port flow and counter samplers.
Page 169 Transition Networks SM24T6DPA Web User Guide Parameter descriptions: Agent Configuration IP Address: The IP address used as Agent IP address in sFlow datagrams. It serves as a unique key that will identify this agent over extended periods of time. Both IPv4 and IPv6 addresses are supported.
Page 170: Smtp Configuration
Transition Networks SM24T6DPA Web User Guide 2-23 SMTP Configuration The function, is used to set an Alarm trap when the switch alarm then you could set the SMTP server to send you the alarm mail. Web Interface To configure the SMTP Configuration in the web interface: 1.
Page 171 Transition Networks SM24T6DPA Web User Guide Buttons: Apply – Click to apply changes. Reset- Click to undo any changes made locally and revert to previously saved values. 33665 Rev. C www.transition.com/ Page 170 of 288...
Page 172: Chapter 3. Monitor
Transition Networks SM24T6DPA Web User Guide Monitor Chapter 3. This chapter describes the network monitoring which includes the Ports, Layer 2 network protocol (e.g., NAS, ACL, DHCP, AAA, RMON) and other switch settings. 3-1 System After you login, the switch shows you the system information. This page is default and tells you the basic information of the system, including “Model Name”, “System Description”, “Contact”,...
Page 173 Transition Networks SM24T6DPA Web User Guide Parameter descriptions: Model Name: Displays the factory defined model name for identification purposes. System Description: Displays the system description. Location: The system location configured in Configuration | System | Information | System Location. Contact: The system contact configured in Configuration | System | Information | System Contact.
Page 174: 3-1.2 Ip Status
Transition Networks SM24T6DPA Web User Guide 3-1.2 IP Status This page displays the status of the IP protocol layer. The status is defined by the IP interfaces, the IP routes and the neighbor cache (ARP cache) status. Web Interface To display the log configuration in the web interface: 1.
Page 175 Transition Networks SM24T6DPA Web User Guide Neighbor cache IP Address: Show the IP address of the entry. Link Address: Show the Link (MAC) address for which a binding to the IP address given exist. Buttons Auto-refresh: Check this box to refresh the page automatically every three seconds.
Page 176: 3-1.3 Log
Transition Networks SM24T6DPA Web User Guide 3-1.3 Log This section describes that display the system log information of the switch Web Interface To display the log configuration in the web interface: 1. Click Monitor, System, Log. 2. Display the log information.
Page 177 Transition Networks SM24T6DPA Web User Guide Buttons Auto-refresh: Check this box to refresh the page automatically every seconds. Refresh: Updates the system log entries, starting from the current entry ID. Clear: Flushes the selected log entries. |<<: Updates the system log entries, starting from the first available entry ID.
Page 178: 3-1.4 Detailed Log
Transition Networks SM24T6DPA Web User Guide 3-1.4 Detailed Log This section describes that display the detailed log information of the switch Web Interface To display the detailed log configuration in the web interface: 1. Click Monitor, System, and Detailed Log.
Page 179: Green Ethernet
Transition Networks SM24T6DPA Web User Guide 3-2 Green Ethernet 3-2.1 Port Power Savings This page provides the current status for EEE. Web Interface To display the Power Savings in the web interface: 1. Click Monitor, Green Ethernet, Port Power Savings.
Page 180: Ports
Transition Networks SM24T6DPA Web User Guide 3-3 Ports The section describes how to monitor the Port detail parameters of the switch ports content or status. 3-3.1 Traffic Overview The section describes the Port statistics information and provides an overview of general traffic statistics for all switch ports.
Page 181: 3-3.2 Qos Statistics
Transition Networks SM24T6DPA Web User Guide 3-3.2 QoS Statistics The section describes the switch display of QoS detailed Queuing counters for a specific switch port for the different queues for all switch ports. Web Interface To display the Queuing Counters in the web interface: 1.
Page 182: 3-3.3 Qcl Status
Transition Networks SM24T6DPA Web User Guide 3-3.3 QCL Status The section will let you know how to configure and shows the QCL status by different QCL users. Each row describes the QCE that is defined. It is a conflict if a specific QCE is not applied to the hardware due to hardware limitations.
Page 183 Transition Networks SM24T6DPA Web User Guide Auto-refresh: Check this box to refresh the page automatically occurs every 3 seconds. Resolve Conflict: Click to release the resources required to add QCL entry, incase conflict status for any QCL entry is 'yes'.
Page 184: 3-3.4 Detailed Statistics
Transition Networks SM24T6DPA Web User Guide 3-3.4 Detailed Statistics The section describes how to provide detailed traffic statistics for a specific switch port. Use the port select box to select which switch port details to display. The displayed counters are the totals for receive and transmit, the size counters for receive and transmit, and the error counters for receive and transmit.
Page 185 Transition Networks SM24T6DPA Web User Guide Parameter descriptions: Auto-refresh: Invokes auto-refresh to refresh the Port Statistics information automatically. Upper left scroll bar: To scroll which port to display the Port statistics with “Port-0”, “Port-1... Receive Total and Transmit Total Rx and Tx Packets : The number of received and transmitted (good and bad) packets.
Page 186 Transition Networks SM24T6DPA Web User Guide Receive Error Counters Rx Drops : The number of frames dropped due to lack of receive buffers or egress congestion. Rx CRC/Alignment : The number of frames received with CRC or alignment errors. Rx Undersize : The number of short 1 frames received with valid CRC.
Page 187: Dhcp
Transition Networks SM24T6DPA Web User Guide 3-4 DHCP 3-4.1 Server DHCP Server is used to allocate network addresses and deliver configuration parameters to dynamically configured hosts called DHCP client. 3-4.1.1 Statistics This page displays the database counters and the number of DHCP messages sent and received by DHCP server.
Page 188 Transition Networks SM24T6DPA Web User Guide DECLINE : Number of DHCP DECLINE messages received. RELEASE : Number of DHCP RELEASE messages received. INFORM : Number of DHCP INFORM messages received. DHCP Message Sent Counters OFFER : Number of DHCP OFFER messages sent.
Page 189: 3-4.1.2 Binding
Transition Networks SM24T6DPA Web User Guide 3-4.1.2 Binding This page displays bindings generated for DHCP clients. Web Interface To Display DHCP Server Binding IP in the web interface: 1. Click DHCP, Server and Binding. Figure 3-4.1.2: DHCP Server Binding IP Table Parameter descriptions: IP : IP address allocated to DHCP client.
Page 190: 3-4.1.3 Declined Ip
Transition Networks SM24T6DPA Web User Guide 3-4.1.3 Declined IP This page displays declined IP addresses. Web Interface To Display DHCP Server Declined IP in the web interface: 1. Click DHCP, Server, Declined IP. Figure 3-4.1.3: DHCP Server Declined IP Parameter descriptions: IP : IP address allocated to DHCP client.
Page 191: 3-4.2 Snooping Table
Transition Networks SM24T6DPA Web User Guide 3-4.2 Snooping Table This page displays the dynamic IP assigned information after DHCP Snooping mode is disabled. All DHCP clients obtained the dynamic IP address from the DHCP server will be listed in this table except for local VLAN interface IP addresses. Entries in the Dynamic DHCP snooping Table are shown on this page.
Page 192: 3-4.3 Relay Statistics
Transition Networks SM24T6DPA Web User Guide 3-4.3 Relay Statistics This page provides statistics for DHCP relay. Web Interface To monitor a DHCP Relay statistics in the web interface: 1. Click Monitor, DHCP, Relay Statistics. Figure 3-4.3: DHCP Relay Statistics Parameter descriptions: Server Statistics Transmit to Server : The number of packets that are relayed from client to server.
Page 193: 3-4.4 Detailed Statistics
Transition Networks SM24T6DPA Web User Guide 3-4.4 Detailed Statistics This page provides statistics for DHCP snooping. Notice that the normal forward per-port TX statistics is not increased if the incoming DHCP packet is done by L3 forwarding mechanism. Also, clearing the statistics on a specific port may not take effect on global statistics since it gathers the different layer overview.
Page 194 Transition Networks SM24T6DPA Web User Guide Rx and Tx Lease Query: The number of lease query (option 53 with value 10) packets received and transmitted. Rx and Tx Lease Unassigned: The number of lease unassigned (option 53 with value 11) packets received and transmitted.
Page 195: Security
Transition Networks SM24T6DPA Web User Guide 3-5 Security 3-5.1 Access Management Statistics This section shows you a detailed statistics of the Access Management including HTTP, HTTPS, SSH. TELNET, and SSH. Web Interface To configure an Assess Management Statistics in the web interface: 1.
Page 196: 3-5.2 Network
Transition Networks SM24T6DPA Web User Guide 3-5.2 Network 3-5.2.1 Port Security 3-5.2.1.1 Switch This section shows the Port Security status. Port Security is a module with no direct configuration. Configuration comes indirectly from other modules - the user modules. When a user module has enabled port security on a port, the port is set-up for software-based learning.
Page 197 Transition Networks SM24T6DPA Web User Guide Users : Each of the user modules has a column that shows whether that module has enabled Port Security or not. A '-' means that the corresponding user module is not enabled, whereas a letter indicates that the user module abbreviated by that letter (see Abbr) has enabled port security.
Page 198 Transition Networks SM24T6DPA Web User Guide 3-5.2.1.2 Port This section shows the MAC addresses secured by the Port Security module. Port Security is a module with no direct configuration. Configuration comes indirectly from other modules - the user modules. When a user module has enabled port security on a port, the port is set-up for software-based learning.
Page 199: 3-5.2.2 Nas
Transition Networks SM24T6DPA Web User Guide 3-5.2.2 NAS 3-5.2.2.1 Switch The section describes to show the each port NAS status information of the switch. The status includes Admin State Port State, Last Source, Last ID, QoS Class, and Port VLAN ID.
Page 200 Transition Networks SM24T6DPA Web User Guide Port VLAN ID : The VLAN ID that NAS has put the port in. The field is blank, if the Port VLAN ID is not overridden by NAS. If the VLAN ID is assigned by the RADIUS server, "(RADIUS-assigned)" is appended to the VLAN ID.
Page 201 Transition Networks SM24T6DPA Web User Guide 3-5.2.2.2 Port The section describes to provide detailed NAS statistics for a specific switch port running EAPOL-based IEEE 802.1X authentication. For MAC-based ports, it shows selected backend server (RADIUS Authentication Server) statistics, only. Web Interface To configure a NAS Port Status Configuration in the web interface: 1.
Page 202 Transition Networks SM24T6DPA Web User Guide • Multi 802.1X • MAC-based Auth. Last Supplicant/Client Info : Information about the last supplicant/client that attempted to authenticate. This information is available for the following administrative states: • Port-based 802.1X • Single 802.1X •...
Page 203 Transition Networks SM24T6DPA Web User Guide • MAC-based Auth.X Clear This: Click to clear both the port counters and all of the attached client's counters. The "Last Client" will not be cleared, however. This button is available in the following modes: •...
Page 204 Transition Networks SM24T6DPA Web User Guide 3-5.2.3 ACL Status The section describes how to shows the ACL status by different ACL users. Each row describes the ACE that is defined. It is a conflict if a specific ACE is not applied to the hardware due to hardware limitations.
Page 205 Transition Networks SM24T6DPA Web User Guide copied to the port number. The allowed values are Disabled or a specific port number. When Disabled is displayed, the port copy operation is disabled. Mirror : Specify the mirror operation of this port. The allowed values are: Enabled: Frames received on the port are mirrored.
Page 206: 3-5.2.3 Arp Inspection
Transition Networks SM24T6DPA Web User Guide 3-5.2.3 ARP Inspection The section describes how to configure the Dynamic ARP Inspection Table parameters of the switch. The Dynamic ARP Inspection Table contains up to 1024 entries, and is sorted first by port, then by VLAN ID, then by MAC address, and then by IP address.
Page 207: 3-5.2.4 Ip Source Guard
Transition Networks SM24T6DPA Web User Guide 3-5.2.4 IP Source Guard Entries in the Dynamic IP Source Guard Table are shown on this page. The Dynamic IP Source Guard Table is sorted first by port, then by VLAN ID, then by IP address, and then by MAC address.
Page 208: 3-5.3 Aaa
Transition Networks SM24T6DPA Web User Guide 3-5.3 AAA 3-5.3.1 RADIUS Overview This section shows you an overview of the RADIUS Authentication and Accounting servers’ status to ensure the function is workable. Web Interface To configure a RADIUS Overview Configuration in the web interface: Click Security, AAA, RADIUS Overview.
Page 209 Transition Networks SM24T6DPA Web User Guide RADIUS Accounting Servers # : The RADIUS server number. Click to navigate to detailed statistics for this server. IP Address : The IP address and UDP port number (in <IP Address>:<UDP Port> notation) of this server.
Page 210: 3-5.3.2 Radius Details
Transition Networks SM24T6DPA Web User Guide 3-5.3.2 RADIUS Details This section shows you a detailed statistics for a particular RADIUS server. Web Interface To configure a RADIUS Details Configuration in the web interface: 1. Specify which Port you want to check.
Page 211 Transition Networks SM24T6DPA Web User Guide Parameter descriptions: RADIUS Authentication Statistics The statistics map closely to those specified in RFC4668 - RADIUS Authentication Client MIB. Use the server select box to switch between the backend servers to show details for.
Page 212 Transition Networks SM24T6DPA Web User Guide Retransmissio transmissions packets retransmitted to the RADIUS authentication server. The number of RADIUS Access-Request packets destined for the server that have not yet timed out or received a response. This variable Pending radiusAuthClientExtPendingR is incremented when an Access-Request is sent...
Page 213 Transition Networks SM24T6DPA Web User Guide from the server. The number of RADIUS packets of radiusAccClientExtUnknownTy Unknown Types unknown types that were received from the server on the accounting port. The number of RADIUS packets that radiusAccClientExtPacketsDrop were received from the server on the...
Page 214: 3-5.4 Switch
Transition Networks SM24T6DPA Web User Guide 3-5.4 Switch 3-5.4.1 RMON 3-5.4.1.1 Statistics This section provides an overview of RMON Statistics entries. Each page shows up to 99 entries from the Statistics table, default being 20, selected through the "entries per page" input field.
Page 215 Transition Networks SM24T6DPA Web User Guide Over-size : The total number of packets received that were longer than 1518 octets. Frag. : The number of frames which size is less than 64 octets received with invalid CRC. Jabb. : The number of frames which size is larger than 64 octets received with invalid CRC.
Page 216 Transition Networks SM24T6DPA Web User Guide 3-5.4.1.2 History This section provides an overview of RMON History entries. Each page shows up to 99 entries from the History table, default being 20, selected through the "entries per page" input field. When first visited, the web page will show the first 20 entries from the beginning of the History table.
Page 217 Transition Networks SM24T6DPA Web User Guide Undersize : The total number of packets received that were less than 64 octets. Oversize : The total number of packets received that were longer than 1518 octets. Frag. : The number of frames which size is less than 64 octets received with invalid CRC.
Page 218 Transition Networks SM24T6DPA Web User Guide 3-5.4.1.3 Alarm This page provides an overview of RMON Alarm entries. Each page shows up to 99 entries from the Alarm table, default being 20, selected through the "entries per page" input field. When first visited, the web page will show the first 20 entries from the beginning of the Alarm table.
Page 219 Transition Networks SM24T6DPA Web User Guide 3-5.4.1.4 Event This page provides an overview of RMON Event table entries. Each page shows up to 99 entries from the Event table, default being 20, selected through the "entries per page" input field. When first visited, the web page will show the first 20 entries from the beginning of the Event table.
Page 220: Lacp
Transition Networks SM24T6DPA Web User Guide 3-6 LACP 3-6.1 System Status This section describes that when you complete to set LACP function on the switch then it provides a status overview for all LACP instances Web Interface To display the LACP System status in the web interface: Click Monitor, LACP, System Status Check “Auto-refresh”.
Page 221: 3-6.2 Port Status
Transition Networks SM24T6DPA Web User Guide 3-6.2 Port Status This section describes that when you complete to set LACP function on the switch then it provides a Port Status overview for all LACP instances Web Interface To display the LACP Port status in the web interface: 1.
Page 222: 3-6.3 Port Statistics
Transition Networks SM24T6DPA Web User Guide 3-6.3 Port Statistics This section describes that when you complete to set LACP function on the switch then it provides a Port Statistics overview for all LACP instances Web Interface To display the LACP Port status in the web interface: 1.
Page 223: Loop Protection
Transition Networks SM24T6DPA Web User Guide 3-7 Loop Protection This section displays the loop protection port status the ports of the currently selected switch. Web Interface To display the Loop Protection status in the web interface: 1. Click Monitor, Loop Protection.
Page 224: Spanning Tree
Transition Networks SM24T6DPA Web User Guide 3-8 Spanning Tree 3-8.1 Bridge Status After you complete the MSTI Port configuration then you could to ask the switch display the Bridge Status. The Section provides a status overview of all bridge instances. The...
Page 225: 3-8.2 Port Status
Transition Networks SM24T6DPA Web User Guide 3-8.2 Port Status After you complete the STP configuration then you could to ask the switch display the STP Port Status. The Section provides you to ask switch to display the STP CIST port status for physical ports of the currently selected switch.
Page 226: 3-8.3 Port Statistics
Transition Networks SM24T6DPA Web User Guide 3-8.3 Port Statistics After you complete the STP configuration then you could to let the switch display the STP Statistics. The Section provides you to ask switch to display the STP Statistics detail counters of bridge ports in the currently selected switch.
Page 227: Mvr
Transition Networks SM24T6DPA Web User Guide 3-9 MVR 3-9.1 Statistics The section describes the switch will display the MVR detail Statistics after you had configured MVR on the switch. It provides the detail MVR Statistics Information Web Interface To display the MVR Statistics Information in the web interface: 1.
Page 228: 3-9.2 Mvr Channels Groups
Transition Networks SM24T6DPA Web User Guide 3-9.2 MVR Channels Groups The section describes user could display the MVR Groups detail information on the switch. Entries in the MVR Group Table are shown on this page. The MVR Group Table is sorted first...
Page 229: 3-9.3 Mvr Sfm Information
Transition Networks SM24T6DPA Web User Guide 3-9.3 MVR SFM Information The MVR SFM (Source-Filtered Multicast) Information Table also contains the SSM (Source-Specific Multicast) information. This table is sorted first by VLAN ID, then by group, and then by Port. Different source addresses belong to the same group are treated as single entry.
Page 230 Transition Networks SM24T6DPA Web User Guide Buttons Auto-refresh: Check this box to refresh the page automatically every 3 seconds. Refresh: Click to refresh the page. |<<: Updates the system log entries to the first available entry ID. >> : Updates the system log entry to the next available entry ID.
Page 231: Ipmc
Transition Networks SM24T6DPA Web User Guide 3-10 IPMC 3-10.1 IGMP Snooping 3-10.1.1 Status After you complete the IGMP Snooping configuration, you can then let the switch display the IGMP Snooping Status. This section lets you display the IGMP Snooping detail status.
Page 232 Transition Networks SM24T6DPA Web User Guide Router Port : Displays which ports act as router ports. A router port is a port on the Ethernet switch that leads towards the Layer 3 multicast device or IGMP querier. Static denotes the specific port is configured to be a router port.
Page 233: 3-10.1.2 Group Information
Transition Networks SM24T6DPA Web User Guide 3-10.1.2 Group Information After you complete to set the IGMP Snooping function then you could let the switch to display the IGMP Snooping Group Information. Entries in the IGMP Group Table are shown on this page.
Page 234: 3-10.1.3 Ipv4 Sfm Information
Transition Networks SM24T6DPA Web User Guide 3-10.1.3 IPv4 SFM Information Entries in the IGMP SFM Information Table are shown on this page. The IGMP SFM (Source-Filtered Multicast) Information Table also contains the SSM (Source-Specific Multicast) information. This table is sorted first by VLAN ID, then by group, and then by Port. Different source addresses belong to the same group are treated as single entry.
Page 235 Transition Networks SM24T6DPA Web User Guide Buttons Auto-refresh: Check this box to refresh the page automatically every 3 seconds. Refresh: Click to refresh the page. |<<: Updates the system log entries to the first available entry ID >>: Updates the system log entry to the next available entry ID 33665 Rev.
Page 236: 3-10.2 Mld Snooping
Transition Networks SM24T6DPA Web User Guide 3-10.2 MLD Snooping 3-10.2.1 Status The section describes when you complete the MLD Snooping and how to display the MLD Snooping Status and detail information. It will help you to find out the detail information of MLD Snooping status.
Page 237 Transition Networks SM24T6DPA Web User Guide Router Port : Display which ports act as router ports. A router port is a port on the Ethernet switch that leads towards the Layer 3 multicast device or MLD querier. Static denotes the specific port is configured to be a router port.
Page 238: 3-10.2.2 Group Information
Transition Networks SM24T6DPA Web User Guide 3-10.2.2 Group Information The section describes user could set the MLD Snooping Groups Information. The "Start from VLAN", and "group" input fields allow the user to select the starting point in the MLD Group...
Page 239: 3-10.2.3 Ipv6 Sfm Information
Transition Networks SM24T6DPA Web User Guide 3-10.2.3 IPv6 SFM Information Entries in the MLD SFM Information Table are shown on this page. The MLD SFM (Source-Filtered Multicast) Information Table also contains the SSM (Source-Specific Multicast) information. This table is sorted first by VLAN ID, then by group, and then by Port. Different source addresses belong to the same group are treated as single entry.
Page 240 Transition Networks SM24T6DPA Web User Guide Buttons Auto-refresh: Check this box to refresh the page automatically every 3 seconds. Refresh: Click to refresh the page. |<<: Updates the system log entries to the first available entry ID. >> : Updates the system log entry to the next available entry ID.
Page 241: Lldp
Transition Networks SM24T6DPA Web User Guide 3-11 LLDP 3-11.1 Neighbor This page provides a status overview for all LLDP neighbors. The displayed table contains a row for each port on which an LLDP neighbor is detected. The columns’ information is described below.
Page 242 Transition Networks SM24T6DPA Web User Guide Buttons Auto-refresh: Check this box to refresh the page automatically every 3 seconds. Refresh: Click to refresh the page. 33665 Rev. C www.transition.com/ Page 241 of 288...
Page 243: 3-11.2 Lldp-Med Neighbor
Transition Networks SM24T6DPA Web User Guide 3-11.2 LLDP-MED Neighbor This page provides a status overview of all LLDP-MED neighbors. The displayed table contains a row for each port on which an LLDP neighbor is detected. This function applies to VoIP devices which support LLDP-MED. The columns hold the following information:...
Page 244 Transition Networks SM24T6DPA Web User Guide and inventory management. LLDP-MED Media Endpoint (Class II) : The LLDP-MED Media Endpoint (Class II) definition is applicable to all endpoint products that have IP media capabilities however may or may not be associated with a particular end user. Capabilities include all of the capabilities defined for the previous Generic Endpoint Class (Class I), and are extended to include aspects related to media streaming.
Page 245 Transition Networks SM24T6DPA Web User Guide TAG : TAG is indicative of whether the specified application type is using a tagged or an untagged VLAN. Can be Tagged or Untagged. Untagged: The device is using an untagged frame format and as such does not include a tag header as defined by IEEE 802.1Q-2003.
Page 246: 3-11.3 Eee
Transition Networks SM24T6DPA Web User Guide 3-11.3 EEE By using EEE power savings can be achieved at the expense of traffic latency. This latency occurs due to that the circuits EEE turn off to save power, need time to boot up before sending traffic over the link.
Page 247 Transition Networks SM24T6DPA Web User Guide Buttons Auto-refresh: Check this box to refresh the page automatically every 3 seconds. Refresh: Click to refresh the page. 33665 Rev. C www.transition.com/ Page 246 of 288...
Page 248: 3-11.4 Port Statistics
Transition Networks SM24T6DPA Web User Guide 3-11.4 Port Statistics Two types of counters are shown. Global counters are counters that refer to the whole switch, while local counters refer to per port counters for the currently selected switch. Web Interface To show LLDP Statistics: 1.
Page 249 Transition Networks SM24T6DPA Web User Guide Local Counters : The displayed table contains a row for each port. The columns hold the following information: Local Port : The port on which LLDP frames are received or transmitted. Tx Frames : The number of LLDP frames transmitted on the port.
Page 250: Mac Table
Transition Networks SM24T6DPA Web User Guide 3-12 MAC Table Entries in the MAC Table are shown on this page. The MAC Table contains up to 8192 entries, and is sorted first by VLAN ID, then by MAC address. Web Interface To Display MAC Address Table in the web interface: 1.
Page 251 Transition Networks SM24T6DPA Web User Guide Buttons Auto-refresh: Check this box to refresh the page automatically every 3 seconds. Clear: Clears the counters for the selected port. Refresh: Click to refresh the page. |<<: Updates the system log entries to the first available entry ID.
Page 252: Vlans
Transition Networks SM24T6DPA Web User Guide 3-13 VLANs 3-13.1 VLAN Membership This page provides an overview of membership status of VLAN users. Web Interface To configure VLAN membership configuration in the web interface: 1. Click Monitor, VLANs, VLAN Membership. 2. Scroll the bar and select which VLANs to be displayed.
Page 253 Transition Networks SM24T6DPA Web User Guide Navigating the VLAN Monitor page Each page shows up to 99 entries from the VLAN table, default being 20, selected through the "entries per page" input field. When first visited, the web page will show the first 20 entries from the beginning of the VLAN Table.
Page 254: 3-13.2 Vlan Port
Transition Networks SM24T6DPA Web User Guide 3-13.2 VLAN Port The function Port Status gathers the information of all VLAN status and reports it by the order of Static NAS MVRP MVP Voice VLAN MSTP GVRP Combined. Web Interface To Display VLAN Port Status in the web interface: 1.
Page 255 Transition Networks SM24T6DPA Web User Guide Frame Type : Shows whether the port accepts all frames or only tagged frames. This parameter affects VLAN ingress processing. If the port only accepts tagged frames, untagged frames received on that port are discarded.
Page 256: Vcl
Transition Networks SM24T6DPA Web User Guide 3-14 VCL 3-14.1 MAC-based VLAN section This shows MAC-based VLAN entries configured by various MAC-based VLAN users. These VLAN User types are currently supported: CLI/Web/SNMP: These are referred to as static. NAS: NAS provides port-based authentication, which involves communications between a Supplicant, Authenticator, and an Authentication Server.
Page 257: 3-14.2 Protocol-Based Vlan
Transition Networks SM24T6DPA Web User Guide 3-14.2 Protocol-based VLAN 3-15.2.1 Protocol to Group This page shows the Protocol to Group Name (unique for each Group) mapping entries for the switch. Web Interface To Display Protocol-based VLAN configuration in the web interface: 1.
Page 258 Transition Networks SM24T6DPA Web User Guide Buttons Auto-refresh: Check this box to refresh the page automatically every 3 seconds. Refresh: Click to refresh the page. 33665 Rev. C www.transition.com/ Page 257 of 288...
Page 259: 3-14.2.2 Group To Vlan
Transition Networks SM24T6DPA Web User Guide 3-14.2.2 Group to VLAN This page displays the configured Group Name to VLAN mapping for the switch. Web Interface To display Group to VLAN configuration in the web interface: 1. Click Monitor, VCL, Group to VLAN.
Page 260: 3-14.3 Ip Subnet-Based Vlan
Transition Networks SM24T6DPA Web User Guide 3-14.3 IP Subnet-based VLAN The page shows IP subnet-based VLAN entries. This page shows only static entries. Web Interface To Display MAC-based VLAN configuration in the web interface: 1. Click Monitor, VCL, and IP Subnet-based VLAN.
Page 261: Sflow
Transition Networks SM24T6DPA Web User Guide 3-15 sFlow This page shows sFlow receiver and per-port statistics. Web Interface To Display MAC-based VLAN configuration in the web interface: 1. Click Monitor, sFlow. 2. Display sFlow information. Figure 3-15: sFlow Statistics Parameter descriptions: Owner : This field shows the current owner of the sFlow configuration.
Page 262 Transition Networks SM24T6DPA Web User Guide Tx Errors : The number of UDP datagrams that has failed transmission. The most common source of errors is invalid sFlow receiver IP/hostname configuration. To diagnose, paste the receiver's IP address/hostname into the Ping Web page (Diagnostics > Ping/Ping6).
Page 263: Chapter 4. Diagnostics
Transition Networks SM24T6DPA Web User Guide Diagnostics Chapter 4. This chapter provides a set of basic system diagnosis. It let users know that whether the system is health or needs to be fixed. The basic system checks include ICMP Ping, Link OAM, ICMPv6, and VeriPHY Cable Diagnostics.
Page 264: Ping6
Transition Networks SM24T6DPA Web User Guide 4-2 Ping6 This section lets you issue ICMPv6 PING packets to troubleshoot IPv6 connectivity issues. Web Interface To configure an ICMPv6 PING Configuration in the web interface: 1. Specify ICMPv6 PING IP Address. 2. Specify ICMPv6 PING Size, Count, Interval, and Egress Interface.
Page 265: Veriphy Cable Diagnostics
Transition Networks SM24T6DPA Web User Guide 4-3 VeriPHY Cable Diagnostics This section is used for running the VeriPHY Cable Diagnostics. Click the Start button to run the diagnostics. This will take approximately 5 seconds. If all ports are selected, this can take approximately 15 seconds.
Page 266: Traceroute
Transition Networks SM24T6DPA Web User Guide 4-4 Traceroute This page lets you issue ICMP, TCP, or UDP packets to diagnose network connectivity issues. Web Interface To configure an ICMPv6 PING Configuration in the web interface: 1. Specify traceroute IP Address.
Page 267: Chapter 5. Maintenance
Transition Networks SM24T6DPA Web User Guide Maintenance Chapter 5. This chapter describes the switch Maintenance configuration tasks to enhance the performance of local network including Restart Device, Firmware upgrade, Save/Restore, Import/Export. 5-1 Restart Device This section describes how to restart switch for any maintenance needs. Any configuration files or scripts that you saved in the switch should still be available afterwards.
Page 268: Factory Defaults
Transition Networks SM24T6DPA Web User Guide 5-2 Factory Defaults This section describes how to reset the Switch configuration to Factory Defaults. Any configuration files or scripts are reset to the factory default values. Web Interface To configure a Factory Defaults Configuration in the web interface: 1.
Page 269: Firmware
Transition Networks SM24T6DPA Web User Guide 5-3 Firmware This section describes how to upgrade switch firmware. The switch can be enhanced with more value-added functions by installing firmware upgrades. 5-3.1 Firmware Upgrade This page facilitates an update of the firmware controlling the switch.
Page 270: 5-3.2 Firmware Selection
Transition Networks SM24T6DPA Web User Guide 5-3.2 Firmware Selection This page provides information about the active and alternate (backup) firmware images in the device, and allows you to revert to the alternate image. The web page displays two tables of information on the active and alternate firmware images.
Page 271: Configuration
Transition Networks SM24T6DPA Web User Guide 5-4 Configuration The switch stores its configuration in a number of text files in CLI format. The files are either virtual (RAM-based) or stored in flash on the switch. There are three system files: running-config: A virtual file that represents the currently active configuration on the switch.
Page 272: 5-4.2 Upload Configuration
Transition Networks SM24T6DPA Web User Guide 5-4.2 Upload Configuration The configuration upload function lets you back up and save the switch configuration into the running web browser on your PC. It is possible to upload any of the files on the switch to the web browser. Select the file and click the Upload Configuration button.
Page 273: 5-4.3 Download Configuration
Transition Networks SM24T6DPA Web User Guide 5-4.3 Download Configuration This section describes to export the switch Configuration for maintenance needs. Any current configuration files will be exported in text format. It is possible to download a file from the web browser to all the files on the switch, except default-config, which is read-only.
Page 274: 5-4.4 Activate Configuration
Transition Networks SM24T6DPA Web User Guide 5-4.4 Activate Configuration It is possible to activate any of the configuration files present on the switch, except for running-config which represents the currently active configuration. Select the file to activate and click the Activate Configuration button to initiate the process of completely replacing the existing configuration with the selected file.
Page 275: 5-4.5 Delete Configuration File
Transition Networks SM24T6DPA Web User Guide 5-4.5 Delete Configuration File It is possible to delete any of the writable files stored in flash, including startup-config. If this is done and the switch is rebooted without a prior save operation, this effectively resets the switch to its default configuration.
Page 276: Chapter 6 Dms Management
Transition Networks SM24T6DPA Web User Guide DMS Management Chapter 6 6-1 DMS Introduction • DMS automatically discovers and displays all devices connected to the switch using standard networking protocols such as LLDP, UPnP, ONVIF, etc. • DMS supports up to 256 devices within four subnets.
Page 277: Specified Dms Controller Switch
Transition Networks SM24T6DPA Web User Guide Note: 1. If there are more than two Switches set as High-priority or no High-priority mode switch, the Switch with the longer system uptime will be selected as the DMS Controller switch. If two Switches have same up time, the Switch with the smaller MAC address will be assigned as the DMS Controller Switch.
Page 278: Dms Information
Transition Networks SM24T6DPA Web User Guide 6-4 DMS Information This page displays general DMS information for the switch including its DMS software version, the number of devices to manage, the MAC Address, and the IP Address for the switch. Web interface To configure DMS Information via the web interface: 1.
Page 279 Transition Networks SM24T6DPA Web User Guide Current IPv4 Address: The current address (IPv4). DMS uses switch interface VLAN1. DMS Working Status: The current DMS state (Enabled or Disabled). System Date: The date stamp currently in the system. System Uptime: The days/hours/minutes that the switch has been up and running.
Page 280: Device List
Transition Networks SM24T6DPA Web User Guide Device List You can identify the system by configuring switch contact information, name, and location. Web interface To configure Surveillance NVR & CMS in the web interface: 1. Select the Surveillance, Management, Surveillance NVR & CMS path.
Page 281: Chapter 7 Dms Graphical Monitoring
Transition Networks SM24T6DPA Web User Guide DMS Graphical Monitoring Chapter 7 Topology View This page lets you view the topology in a cluster of networks. Web interface To configure Topology View in the web interface: 1. Select DMS, Graphical Monitoring, Topology View.
Page 282: Floor View
Transition Networks SM24T6DPA Web User Guide Floor View This page lets an administrator place a device per time onto the custom image, which you have already uploaded, by dragging-and-dropping markers in the device list. Floor View features include: • Anchor devices onto Floor Maps •...
Page 283: Map View
Transition Networks SM24T6DPA Web User Guide Map View This page lets you view a realistic representation of device in the network. To find one of devices within the network, enter the device name in the search bar. Click “Device List” to hide the “Device List”...
Page 284: Chapter 8 Dms Maintenance
Transition Networks SM24T6DPA Web User Guide DMS Maintenance Chapter 8 8-1 Floor View This page lets an administrator add or delete a custom map or floor image. Floor View features include: • Anchor devices onto Floor Maps • Find device location instantly •...
Page 285: Export Device Info
Transition Networks SM24T6DPA Web User Guide 8-2 Export Device Info You can export the device information in PC. Web interface To configure Information in the web interface: 1. Click Surveillance, Maintenance, and Device info to CSV. 2. Click the Export button.
Page 286: Traffic Monitor
Transition Networks SM24T6DPA Web User Guide 8-4 Traffic Monitor This page displays visual chart of network traffic of all the devices managed by PoE surveillance switch. Web interface To configure Surveillance Information in the web interface: 1. Click Maintenance, Traffic Monitor.
Page 287: Dms Troubleshooting
Transition Networks SM24T6DPA Web User Guide 8-5 DMS Troubleshooting Problem: The switch lists itself as the only device in Topology View of DMS. Problem: In DMS, the Local image shows the IP address of another switch. Description: The switch is listed as only device in DMS Topology View in DMS; all devices are listed in DMS device list.
Page 288: Appendix A Troubleshooting
Check the adapter on the attached device and cable connections for possible defects. Replace the defective adapter or cable if necessary. 4. Make sure all devices connected to the SM24T6DPA are configured to auto negotiate, or are configured to connect at half duplex (all hubs are configured this way, for example).
Page 289: Appendix B Service, Warranty And Tech Support
Transition Networks SM24T6DPA Web User Guide Service, Warranty and Tech Support Appendix B See the SM24T6DPA Install Guide for related information. Compliance Information Appendix C See the SM24T6DPA Install Guide for related information. 33665 Rev. C www.transition.com/ Page 288 of 288...
Page 290 10900 Red Circle Drive Minnetonka, MN 55343 USA Tel: 952- 941-7600 or 1-800-526-9267 Fax: 952-941-2322 Copyright© 2015-2018 Transition Networks. All rights reserved. Printed in the U.S.A. SM24T6DPA Web User Guide, 33665 Rev C 33665 Rev. C www.transition.com/ Page 289 of 288...

Transition SM24T6DPA Web User Manual

Overview of this Manual

Introduction

Related Manuals

Chapter 1 Operation of Web-Based Management

Chapter 2 System Configuration

System

Green Ethernet

Ports Configuration

Dhcp

Security

Aggregation

Broadcast Storm Protection

Loop Protection

Spanning Tree

IPMC Profile

Mvr

Ipmc

Lldp

MAC Table

Vlans

Private Vlans

Vcl

Voice VLAN

Qos

Mirror

Upnp

Gvrp

Sflow

SMTP Configuration

Chapter 3. Monitor

System

Green Ethernet

Ports

Dhcp

Security

Lacp

Loop Protection

Spanning Tree

Mvr

Ipmc

Lldp

MAC Table

Vlans

Vcl

Sflow

Chapter 4. Diagnostics

Ping

Ping6

Veriphy Cable Diagnostics

Traceroute

Chapter 5. Maintenance

Restart Device

Factory Defaults

Firmware

Configuration

Chapter 6 Dms Management

DMS Introduction

DMS Mode

Specified DMS Controller Switch

DMS Information

Device List

Chapter 7 Dms Graphical Monitoring

Topology View

Topology View Icons / Controls

Floor View

Map View

Chapter 8 Dms Maintenance

Floor View

Export Device Info

Troubleshooting

Traffic Monitor

DMS Troubleshooting

For more DMS Information

Appendix A Troubleshooting

Appendix B Service, Warranty and Tech Support

Appendix C Compliance Information

Quick Links

Troubleshooting

Need help?