Advertisement
Quick Links
General mounting instructions for closures
1. Establish position of closures.
2. A mounting gauge can be made as an additional aid.
3. Choose fixings which are suitable for the base material.
The bearing surface for the hinges on the doorframe and
door must be sufficiently strong.
4.Mount closures and screws, made sure components (e.g. blocks to closure)
are parallel.
Caution
if elements not parallel
- occurrence of noise
- increased wear
- broken seal
5. Make sure there is the same distance between door and frame all round!
correct
incorrect
incorrect
Advertisement
Related Manuals for Rahrbach TURNO 7101
Summary of Contents for Rahrbach TURNO 7101
- Page 1 General mounting instructions for closures 1. Establish position of closures. 2. A mounting gauge can be made as an additional aid. 3. Choose fixings which are suitable for the base material. correct The bearing surface for the hinges on the doorframe and door must be sufficiently strong.
- Page 2 Caution Wrongly mounted or positioned hinges can cause damage to the closing system. Rahrbach closures are only to be used for industrial applications. In order to avoid danger of injury, the plant operator is responsible for replacing faulty closures immediately.
- Page 3 Technical data sheet for TURNO type of closure: surface-mounted closure article no.: 7101 area of application cold stores 1. can be used on left or right-hand side: yes, depending on design 2. corrosion: all components are corrosion-protected (available in brass or stainless steel, excepting profile cylinder) 4.
- Page 5 Illustrations and texts are without obligation. We reserve the right for technical modifications due to new legal requirements or errors. 01.03...
- Page 6 Assembly instructions for TURNO Series 7101 Obey the technical data sheet and instructions! 1. Five overviews of TURNO application variants for different doors and frames.
- Page 7 Assembly instructions for TURNO Series 7101 Obey the technical data sheet and instructions! Note TOP position! Boring must be present! For disassembly, see 16. min. 6 - max. 10 screws 37° 37° R 40 R 40 8 mm 8 mm Hole template Hole template for outer side of door,...
- Page 8 Assembly instructions for TURNO Series 7101 Obey the technical data sheet and instructions! Caution: Only mount with disassembly boring! 3. Screw flange onto outer door side according to hole template. Mount Turno outside handle with a simple turning and snap movement, without additional tools. Caution: Only mount Turno when open!
- Page 9 Assembly instructions for TURNO Series 7101 Obey the technical data sheet and instructions! compensation disc 1 mm Marking must be level with underside! 4. The adapter is fixed with 4 x M4 screws onto inner opener 5. It may be necessary to use additional adapters (depending on door thickness!). (compensation for tolerance by means of compensation disc, see 11).
- Page 10 Assembly instructions for TURNO Series 7101 Obey the technical data sheet and instructions! sticker hole template for inner side of door Securing with Loctite No. 243 recommended! 6. Screw inner opener to door and press in plugs. Position sticker (optional) next to inner opener.
- Page 11 Assembly instructions for TURNO Series 7101 Obey the technical data sheet and instructions! sticker hole template for inner side of door Securing with Loctite No. 243 recommended! 7. Screw inner opener for doors opening towards the inside to door and press in plug.
- Page 12 Assembly instructions for TURNO Series 7101 Obey the technical data sheet and instructions! hole template for inner side of door Securing with Loctite No. 243 recommended! 8. Screw push inner opener to door and press in plug.
- Page 13 Assembly instructions for TURNO Series 7101 Obey the technical data sheet and instructions! sticker Securing with Loctite No. 243 recommended! hole template for inner side of door 9. Screw inner opener for multi-point locking to door and press in plugs.
- Page 14 Assembly instructions for TURNO Series 7101 Obey the technical data sheet and instructions! Lubricate! max. 8 Securing with Loctite No. 243 recommended! 10. Rod assembly for multi-point locking. Caution: It is particularly important to maintain the dimensions 6 and 8 mm as otherwise functional disturbances may occur.
- Page 15 Assembly instructions for TURNO Series 7101 Obey the technical data sheet and instructions! mounting of inner opener on outer lock Disassembly of inner opener on outer lock 11. Insert central screw M8 x 35 through the central opening. (Length of screw is dependent on door thickness). The lock must be adjusted with the spacer plates in such a way that the lock when mounted returns to the locked condition automatically by spring force (see 4).
- Page 16 Assembly instructions for TURNO Series 7101 Obey the technical data sheet and instructions! reserve boring Central screw for final fixing! 12. Position closing cam and mount on the outer screw holes on the frame. Check closing, adjust closing pressure if necessary by adjusting cam, finally fix closing cam with the central screw.
- Page 17 Assembly instructions for TURNO Series 7101 Obey the technical data sheet and instructions! 13. Position block and mount on frame. Check closing.
- Page 18 Assembly instructions for TURNO Series 7101 Obey the technical data sheet and instructions! Central screws for final fixing! 14. Position plate and mount at outer screw holes. Check closing, adjust closing pressure if necessary by adjusting plate, finally fix plate with central screw.
- Page 19 Assembly instructions for TURNO Series 7101 Obey the technical data sheet and instructions! reserve boring Central screw for final fixing! 15. Position closing cam and mount on the outer screw holes on the frame. Check closing, adjust closing pressure if necessary by adjusting cam, finally fix closing cam with the central screw.
- Page 20 Assembly instructions for TURNO Series 7101 Obey the technical data sheet and instructions! 16. Turno disassembly: Remove company logo, remove central screws and disassemble inner opener.
- Page 21 Assembly instructions for TURNO Series 7101 Obey the technical data sheet and instructions! 17. Remove outer handle with a screwdriver which fits the disassembly boring.
- Page 22 Assembly instructions for TURNO Series 7101 Obey the technical data sheet and instructions! 18. Cylinder disassembly as follows: 1. Insert key. 2. Remove cylinder screw with screwdriver. 3. Turn screwdriver until cylinder can be removed.
- Page 23 Assembly instructions for TURNO Series 7101 Obey the technical data sheet and instructions! "inner" seal order no. 7101.0233 "outer" seal order no. 7101.0234 Icing / condensation 19. In order to to prevent icing / condensation, rubber seals (optional) are fitted under the outer handle and inner opener.