Summary of Contents for 2TEST TETRA DVI-100
- Page 1 DVI-100 User Guide www.2test.ru + 7 495 215-57-17 info@2test.ru Цены и срок поставки уточняйте на сайте , по телефону: или...
-
Page 2: Table Of Contents
Funk-Electronic Piciorgros GmbH DVI-100 User Guide Content Content..................................2 Introduction ............................... 3 Overview ................................. 3 Safety Precautions ............................3 Disclaimer...............................3 General description ............................4 Application scenarios ............................. 4 1.5.1 Back to Back Operation ..........................4 1.5.2 Connected to the iPhone or a Computer....................5 Connected by IP directly to a TETRA switch ................... -
Page 3: Introduction
Funk-Electronic Piciorgros GmbH DVI-100 User Guide Introduction Overview This document contains information about installation, settings, and operation of the DVI-100 TETRA Radio Modem. This includes practical guidance relating to antenna selection and installation, operating range, extension modules, software support, etc. Safety Precautions This equipment transmits radio waves in the frequency range 380 to 470 MHz or -800 MHz. -
Page 4: General Description
Funk-Electronic Piciorgros GmbH DVI-100 User Guide General description The DVI-100 (Digital Voice Interface) will be attached to a TETRA Network in the same way as a normal TETRA hand portable, and it can be a Member of up to 25 talkgroups. -
Page 5: Connected To The Iphone Or A Computer
Funk-Electronic Piciorgros GmbH DVI-100 User Guide 1.5.2 Connected to the iPhone or a Computer Using the DVI with IP, the voice data can easily be sent to, or received by, a remote application, potentially running on any type of device. This allows the voice call to be bridged between the TETRA infrastructure and another device. -
Page 6: Connected By Ip Directly To A Tetra Switch
Funk-Electronic Piciorgros GmbH DVI-100 User Guide 1.5.3 Connected by IP directly to a TETRA switch The PTX Protocol developed by the University of Dortmund and Piciorgros GmbH is license free and can be implemented to an interface device (PC) or directly into a TETRA switch. -
Page 7: Tetra Mircospot With Dvi-100 In Dmo Mode
Funk-Electronic Piciorgros GmbH DVI-100 User Guide 1.5.4 TETRA MircoSPOT with DVI-100 in DMO mode This configuration can be used to create a local TETRA access point (MicoSPOT) which operates in DMO mode. The DVI-100 in DMO mode is connected by an IP connection to another DVI-100 in server mode, which is attached to a TETRA network. -
Page 8: Access The Embedded Web Server
Funk-Electronic Piciorgros GmbH DVI-100 User Guide Access the embedded Web server The whole configuration is done by accessing the internal web server of the DVI-100 and changing certain parameters using the user-friendly interface. The first to do is to integrate the device into the local network. The network is supposed to use addresses of the type 192.168.0.xxx. -
Page 9: Register The Dvi-100 To The Tetra Network
Funk-Electronic Piciorgros GmbH DVI-100 User Guide Register the DVI-100 to the TETRA Network In factory default state there is no information available for the device to enter the TETRA network. This is why the TETRA parameters have to be configured before the device is able to register on the network. -
Page 10: Tmo Mode Parameters
Funk-Electronic Piciorgros GmbH DVI-100 User Guide TMO mode parameters If the TMO mode is configured, at least one scan range for the lookup of base stations of the TETRA network must be configured. Here, the value of the first (lowest) scan frequency must be inserted. -
Page 11: Configure The Available Tetra Groups
Funk-Electronic Piciorgros GmbH DVI-100 User Guide Configure the available TETRA groups The DVI-100 manages up to 25 TETRA groups. Each group must be configured in the infrastructure. The DVI-100 can register to these groups and they have to be programmed at “TETRA >> Group configuration”. To configure the "selected"... - Page 12 Funk-Electronic Piciorgros GmbH DVI-100 User Guide Enabled Only enabled groups are registered towards the TETRA network. This feature can be used to temporarily prevent a group from being registered in the TETRA network without removing it completely from the DVI-100 configuration. Group mode Scanned groups are participants of the communication.
-
Page 13: General Setup
Funk-Electronic Piciorgros GmbH DVI-100 User Guide General Setup Read general DVI-100 information and change the designation To get general information about the device on hand the menu item “Device >> Common” can be selected. The delivered data contains detailed information about the device and version numbers. -
Page 14: Adjust The Internal Clock
Funk-Electronic Piciorgros GmbH DVI-100 User Guide Adjust the internal clock The internal clock can be adjusted manually at “Device >> Internal clock”. Here the date can be entered as “dd/mm/yyyy” and the time information as “hh/mm/ss”. To apply the inserted time, the user has to set the option “Set clock” to “Yes” and press the “Apply”... -
Page 15: Change The Dvi-100 Network Setting
Funk-Electronic Piciorgros GmbH DVI-100 User Guide Change the DVI-100 network setting The menu item “Ethernet >> Network” links to the configuration page for the Ethernet interface. Here the IP address of the DVI-100 as well as the netmask and the gateway information can be defined. -
Page 16: The Eventlogger
Funk-Electronic Piciorgros GmbH DVI-100 User Guide The Eventlogger The eventlogger stores information about the behaviour of the DVI-100. Special events are able to trigger messages which allow the user to detect e.g. configuration problems. The logger can be accessed at „Service >> eventlogger“. V1.01 page 16 of 24... -
Page 17: Dvi-100: Client Mode
Funk-Electronic Piciorgros GmbH DVI-100 User Guide DVI-100: Client mode Activation of the client mode To define the DVI-100 device to work as client, the configuration site at “DVI >> General configuration” contains the relevant settings. The option “DVI-100 mode” is the main selection and has to be set to “Client”. Own DV IP Port Sending and listening port at the Ethernet interface of the DVI-100 (Default is port 3141). -
Page 18: Configure The Connection Parameters
Funk-Electronic Piciorgros GmbH DVI-100 User Guide Configure the connection parameters Each client can be identified with the combination of username and password. At the site “DVI >> Client configuration” these information can be edited for the device in hand. Regarding the following screenshot the users’ information (username and password) can be configured in the upper two fields. -
Page 19: Dvi-100: Server Mode
Funk-Electronic Piciorgros GmbH DVI-100 User Guide DVI-100: Server mode Activation of the server mode To define the DVI-100 device to work as server, the configuration site at “DVI >> General configuration” contains the relevant settings. The option “DVI-100 mode” is the main selection and has to be set to “Server”. Own DV IP Port Sending and listening port at the Ethernet interface of the DVI-100 (Default is port 3141). -
Page 20: Manage The Client List
Funk-Electronic Piciorgros GmbH DVI-100 User Guide Manage the client list As soon as the DVI-100 is installed to work as server, the device has to be programmed with the account information of the potential clients. The site “DVI >> Server configuration”... -
Page 21: View The Connection Status
Funk-Electronic Piciorgros GmbH DVI-100 User Guide View the connection status To get the information about the participants which are currently connected the user can select the menu item “DVI >> Status information”. Here the operating mode is shown. In case that the current device is a server, the following picture declares the operating mode as “Server mode”. -
Page 22: Preparation And Setup
Funk-Electronic Piciorgros GmbH DVI-100 User Guide DVI-100 Firmware update procedure The firmware of the DVI-100 can be easily updated. To perform the update, just a TFTP client is needed. A simple command-line client is built directly into Windows operating system. Preparation and setup For updating the DVI-100 you will need the following equipment: •... -
Page 23: Connecting The Dvi-100
Funk-Electronic Piciorgros GmbH DVI-100 User Guide Connecting the DVI-100 Connect the Ethernet port of the DVI-100 to the PC. The IP-settings of the PC must allow it to access the DVI-100 (default IP: 192.168.0.199). Update using the Windows command line client Start the Windows command line by using "Start"... -
Page 24: V1.01
The .pch file must always match to the corresponding firmware. Otherwise an error message will be displayed and the update operation will not be started: www.2test.ru + 7 495 215-57-17 info@2test.ru Цены и срок поставки уточняйте на сайте...