Advertisement
INSTALL/START-UP OF FILTRATION
)
1 Be sure correct amount of filter media sand is in tank and that all connections have been made and are secure.
)
2 Depress control valve handle and rotate to BACKWASH position. (To prevent damage to control valve seal, always depress
handle before turning.)
)
3 Prime and start pump. Never tun pump dry! Running pump dry may damage seals,causing leakage and flooding! Fill pump
with water before starting motor. (be sure all suction and return lines are open), allowing the filter tank to fill with water. Once
water is flowing out of the waste line, run the pump for at least 1 minute. The initial back-washing of the filter is recommended to
remove any impurities or fine sand particles in the sand media.
4 Turn pump off and set valve to RINSE position. Start pump and operate until water in sight glass is clear, about 1/2 to 1 minute.
)
Turn pump off and set valve to FILTER position and restart pump.The filter is now operating in the normal filter mode, filtering dirt
particles from the pool water.
)
5 Adjust pool suction and return valves to achieve desired flow. Check system and filter for water leaks and tighten
connections, bolts, nuts, as required.
)
6 Note the initial pressure gauge reading when the filter is clean. (It will vary from pool to pool depending upon the pump and
general piping system.) As the filter removes dirt and impurities from the pool water, the accumulation in the filter will cause
the pressure to rise and flow to diminish. When the pressure gauge reading is 1.5 bar, higher than the initial "clean" pressure you
noted, it is time to backwash the filter (see BACKWASH under filter and control valve functions).
NOTE: During initial clean-up of the pool water it may be necessary to backwash frequently due to the unusually heavy initial dirt
load in the water.
REPLACEMENT PARTS OF FILTER
Key No.
Part No.
Description
1*
88280105
1.5" Top Mount Valve (Black/ White Colour)
2*
89280101
1.5" Union with Sight Glass,O-Ring (Black/ White Colour)
3*
89280102
1.5" Union Set With O-Ring (Black/ White Colour)
4
06021001
Plastic Pressure Gauge with O-Ring (35psi)
4
01111048
Connector for Pressure Gauge/ Stopper
5
89030204
Hose Adaptor with O-Ring
6
02011026
Sleeve for Hose
7
89031501
FSP350-6W Plastic Hose with Nut
7
89031601
FSP400-6W Plastic Hose with Nut
7
89031701
FSP450-6W Plastic Hose with Nut
7
89031801
FSP500-6W Plastic Hose with Nut
7
89031901
FSP650-6W Plastic Hose with Nut
8
01013049
Hose Adaptor with Nut
9
02011104
O-Ring for 1.5" Union
10
88022401
FSF350-4W Pump (SS020)
10
88022402
FSF400-6W Pump (SS033)
10
88022403
FSP450-6W Pump (SS050)
10
88022404
FSP500-6W Pump (SS075)
10
88022405
FSP650-6W Pump (SS100)
11
89032001
Pump Assembly Screw
12
01271010
Clamp Lock
13
02011134
O-Ring for Filter Neck
14
01331005
P350 Filter Tank
14
01331006
P400 Filter tank
14
01331007
SP/P450 Filter tank
14
01331008
SP/P500 Filter tank
14
01331010
SP/P650 Filter tank
15
89011602
P350 Lateral Assembly with Center Pipe
16
89011603
P400 Lateral Assembly with Center Pipe
16
89011604
P450 Lateral Assembly with Center Pipe
16
89011605
P500 Lateral Assembly with Center Pipe
16
89011606
P650 Lateral Assembly with Center Pipe
17
01172007
Laterals (115mm) for P/V400-P/V450
17
01172008
Laterals (126mm) for P/V500-P/V650
18
89011601
Water Drain Set
19
01111056
FSP/F350-4-6W Combo Base
19
01111053
FSP/F400-6W - FSP/F650-6W Combo base
20
89010119
M6 x 50 Screws with Nut
Qty
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
1
1
1
8
8
1
1
1
2
2
SS PUMP REPLACEMENT PARTS
1
15
23
2
11
3
4
12 13
7
8
9
10
14 16
5
6
Item
Part No.
Description
Qty Item
1
01201031
Transparent Lid
1
2
02011074
O-Ring for lid
1
3
01112051
Basket
1
4
01021064
SS Pump Pre-filter
1
5
89280105
1.5"union
2
6
89022402
Drain Plug With O'ring
1
7
02011004
O-Ring for diffuser
1
8
01111014
Diffuser
1
01311015
Impeller SS020(220V/50Hz)
1
01311016
Impeller SS033(220V/50Hz)
1
01311017
Impeller SS050(220V/50Hz)
1
9
01311018
Impeller SS075(220V/50Hz)
1
01311019
Impeller SS100(220V/50Hz)
1
01311014
Impeller SS120(220V/50Hz)
1
10
89022403
M8*16 Screw with washer
4
11
04015033
1/2"Mechanical seal
1
12
02011090
O-Ring for Flange
1
13
01021065
SS Pump Flange
1
14
03011035
M6*30 Screw
8
15
02011156
Motor Slinger for SS020-SS033
1
PRIMING PUMP
Release all air from filter and piping system.
In a flooded suction system (water source higher than pump), pump will prime itself when suction and
discharge valves are opened.
If pump is not in a flooded suction system, unscrew and remove trap cover; fill trap and pump with water.
Clean and inspect Ring; re-install on trap cover.
Replace trap cover on trap; turn clockwise to tighten cover.
NOTICE: Tighten trap cover by hand only .Pump should prime now. Priming time will depend on vertical
length of suction lift and horizontal length of suction piping.
18
18
19
22
21
17
17
17
Part No.
Description
15
02011153
Motor Slinger for SS050-SS120
16
89022404
Motor support
89022109
Motor SS020(220V/50Hz)
89022110
Motor SS033(220V/50Hz)
89022105
Motor SS050(220V/50Hz)
17
89022106
Motor SS075(220V/50Hz)
89022107
Motor SS100(220V/50Hz)
89022108
Motor SS120(220V/50Hz)
04016009
Capacitor for SS050 Pump(220V/50Hz/60Hz)
04016010
Capacitor for SS075 Pump(220V/50Hz/60Hz)
18
04016012
Capacitor for SS100、SS120 Pump(220V/50Hz/60Hz)
04016030
Capacitor for SS020 Pump(220V/50Hz/60Hz)
04016031
Capacitor for SS033 Pump(220V/50Hz/60Hz)
19
89022112
Cable Box for SS050-SS120 Pump
20
89022111
Cable Box for SS020-SS033 Pump
01031027
Cooling fan for SS050-SS120 Pump
21
01031026
Cooling fan for SS020-SS033 Pump
01031011
Fan Cover for SS020-SS033 Pump
22
01031010
Fan Cover for SS050-SS120 Pump
23
02011104
O-Ring
3
20
22
21
17
Qty
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
Advertisement
