Advertisement
3) Replace filter coping (with O'ring in place).
a) Mount the O-ring for filter neck, covered with transparent lid.
b) Lock the clamp lock, pay attention to the clamp lock clip on both sides are even.
c) Install the pressure gauge and air release valve to the transparent lid.
d) Connect the pump outlet to the valve inlet,a preliminary combination has completed.
4) Make return to pool pipe connection to control valve opening marked RETURN and complete other
necessary plumbing connections, suction lines to pump, waste, etc.
5) Make electrical connections to pump per pump instructions.
6) To prevent water leakage, be sure all pipe connections are tight.
MAIN DIMENSION
DIMENSION TABLE
High
Diameter
Valve
Model
A
B
mm
mm
inch
S450
730
455
1.5 "
S500
770
535
1.5 "
S650
850
635
1.5 "
S700
960
710
1.5 "
INSTALL/START-UP OF FILTER
1) Be sure correct amount of filter media sand is in tank and that all connections have been made and are
secure.
2) Depress control valve handle and rotate to BACKWASH position. (To prevent damage to control valve
seal, always depress handle before turning.)
3) Prime and start pump according to pump instructions (be sure all suction and return lines are open),
allowing the filter tank to fill with water. Once water is flowing out of the waste line, run the pump for at
least 1 minute. The initial back-washing of the filter is recommended to remove any impurities or fine sand
particles in the sand media.
4) Turn pump off and set valve to RINSE position. Start pump and operate until water in sight glass is clear,
about 1/2 to 1 minute.Turn pump off and set valve to FILTER position and restart pump.The filter is now
operating in the normal filter mode, filtering dirt particles from the pool water.
5) Adjust pool suction and return valves to achieve desired flow. Check system and filter for water leaks and
tighten connections, bolts, nuts, as required.
6) Note the initial pressure gauge reading when the filter is clean. (It will vary from pool to pool depending
upon the pump and general piping system.) As the filter removes dirt and impurities from the pool water,
the accumulation in the filter will cause the pressure to rise and flow to diminish. When the pressure gauge
reading is 1.5 bar, higher than the initial "clean" pressure you noted, it is time to backwash the filter (see
BACKWASH under filter and control valve functions).
Sand
kg
45
85
145
210
B
2-4
A
REPLACEMENT PARTS OF MULTIPORT VALVE
Key No.
Part No.
1
01013002
Handle (Small)
2
03018008
Pin for Handle
3
01181001
Washer for Handle
89281203
M6×25 Screw with Nut for Camber Lid
4
89280107
M6*30 Screw with Nut for Standard Lid
5
1.5"Side Mount Valve Standard Lid (White)
01051010
6
02011022
O-Ring for 1.5" Valve Rotor
7
01181002
Washer for Spring
8
02011002
O-Ring for 1.5" Valve Lid
Spring for 1.5" Simd Mount Valve
9
03014001
10
01021001
1.5" Valve Rotor
11
02311002
Spider Gasket
12
01051021
1.5" Side Mount Valve Bottom Body (White)
01111048
Connector for Pressure Gauge/Stopper
13
02011139
O-ring
14
89021303
Drain Plug with O-ring
15
06011032
Oil Pressure Gauge with O-ring (40Psi)
16
02020013
O-Ring
17
01051022
1.5"Union Tale (White)
18
01013017
1.5" Union Nut (Black)
19
89280104
Sight Glass with O-Ring
01051023
1.5" Side Mount Valve Plug (White)
20
01051193
1.5" Elbow Tube (White) 120mm
21
01171002
22
1.5" Union Adaptor (Metric)
01051013
23
1.5"Connector with External Thread(White)
02011003
O-Ring φ59×φ53×φ3
24
01171153
1.5"Union Adaptor
25
REPLACEMENT PARTS OF FILTER
Key
Part No.
No.
1
89010701
Air Release Valve with Oring
2
06011032
Maximum 40PSI Indication, Stainless Steel Casing
3
01201022
Lid (Transparent)
4
01271010
Clamp Lock
5
03021035
M6 Nut
6
03011095
Screw
7
02011134
O-Ring for Filter Neck
8
89010706
Filter Tank for S450
8
89010705
Filter Tank for S500
8
89010704
Filter Tank for S650
8
89010703
Filter Tank for S700
9
02011003
O-Ring for 1.5" adaptor
6 Way 1.5" Valve with Piping Kit, 1.5" union set x 3
10
88280811W
and pressure gauge (White)
11
89010708
The Inner Tank System for S450
11
89010709
The Inner Tank System for S500
11
89010710
The Inner Tank System for S650
11
89010711
The Inner Tank System for S700
12
01111046
1.5"Tank System Support
13
01172007
Laterals(115mm)
13
01172008
Laterals (126mm)
14
89010107
Water Drain Set
15
01111059
16-21inch Filter Base
15
01111062
21-28inch Filter Base
Product Description
Qty
1
1
1
2
6
6
4
1
2
1
6
1
8
1
9
1
1
11
1
1
12
1
1
23
24
25
1
18
5
1
5
1
1
1
1
3
5
3
3-4
Description
Qty
1
1
1
2
1
1
1
1
1
1
1
2
1
1
1
1
1
1
8
8
1
1
1
1
3
5
7
15
10
13
14
16
16
17
18
19
16
20
21
22
18
Advertisement
