Dimensions; Install/Start-Up Of Filter; Replacement Parts Of Filter; Replacement Parts Of Multiport Valve - emaux S700B Manual

3 Replace filter coping. Put the twelve nuts and washers onto each of the twelve bolts, then screw all the nuts )
on with wrench,ensuring that all nuts are tight.
a ) Carefully screw pressure gauge (with O'ring in place) into tapped hole in the filter coping. Do not over-
tighten.
b) Ensure air relief valve (with O'ring in place) is tight fit to filter coping and turn it easily.
4 Connect pump to control valve opening marked PUMP. )
5 Make return to pool pipe connection to control valve opening marked RETURN and complete other )
necessary plumbing connections, suction lines to pump, waste, etc.
6 Make electrical connections to pump per pump instructions. )
7 To prevent water leakage, be sure all pipe connections are tight. )
MAIN DIMENSION
DIMENSION TABLE
High
Diameter Valve Port
Model A B Size
mm mm
Inch
S700(B) 890 723 2"
S800 1050 820 2"
S900 1180 920 2"

INSTALL/START-UP OF FILTER

1) Be sure correct amount of filter media sand is in tank and that all connections have been made and are
secure.
2) Depress control valve handle and rotate to BACKWASH position. (To prevent damage to control valve
seal, always depress handle before turning.)
3) Prime and start pump according to pump instructions (be sure all suction and return lines are open),
allowing the filter tank to fill with water. Once water is flowing out of the waste line, run the pump for at
least 1 minute. The initial back-washing of the filter is recommended to remove any impurities or fine sand
particles in the sand media.
4) Turn pump off and set valve to RINSE position. Start pump and operate until water in sight glass is clear,
about 1/2 to 1 minute.Turn pump off and set valve to FILTER position and restart pump.The filter is now
operating in the normal filter mode, filtering dirt particles from the pool water.
5) Adjust pool suction and return valves to achieve desired flow. Check system and filter for water leaks and
tighten connections, bolts, nuts, as required.
6) Note the initial pressure gauge reading when the filter is clean. (It will vary from pool to pool depending
upon the pump and general piping system.) As the filter removes dirt and impurities from the pool water,
the accumulation in the filter will cause the pressure to rise and flow to diminish. When the pressure gauge
reading is 1.5 bar, higher than the initial "clean" pressure you noted, it is time to backwash the filter (see
BACKWASH under filter and control valve functions).
NOTE: During initial clean-up of the pool water it may be necessary to backwash frequently due to the unusually
heavy initial dirt load in the water.
Sand
Kg
215
355
470
B
2-4
A
Notes:11* 01172010 laterals (185mm) is for S700B
11* 01172011 laterals (233mm) is for S800 & S900
Key No. Part No.
1 01013003
2 03018008
3 01181027
4 01051026
5 89280301
01111048
6
02011139
7 89021303
8 06011029
9 02020016
10 01051033
11 01171154
12 01051032
13 02011009
14 01181002
15 02011022
16 03014014
17 01021002
18 02311003
19 01051027
20 89280104
21 02011011
22 01051035
23 01013034
24 02020017
25 01051029
26 01051195
27 01171035

REPLACEMENT PARTS OF FILTER

Key
Part No.
No.
1 89010601
2 89010701
3 06011032
4 01172005
5 02011126
6 89011202
6 89011208
6 89011209
7 89011203
7 89011210
7 89011211
8 01111090
9 02011127
10 88280813W
11 01172010
11 01172011
12 89010107
13 01111062
13 01112038

REPLACEMENT PARTS OF MULTIPORT VALVE

Product Description Qty 1
Handle (Big) 1 2
Pin for Handle 1
Washer for Handle 1 3
2.0" Side Mount Valve Squareness Lid (White) 1
5
10
M6*32 Screw with Nut
4
Connector for Pressure Gauge/Stopper 1
O-Ring 1
6
1
Drain Plug with O'Ring
7
Oil Pressure Gauge With O-ring (40psi) 1
8
O-Ring for 2.0"Union
2.0" Connector(White) 3
2.0" Union (A/E) 3
3
2.0" Union Nut(White)
1
O-Ring for 2.0" Valve Lid
Washer for spring 1
O-Ring for 2.0" Valve Rotor 2
Spring 1
20
1
2.0" Valve Rotor
Spider Gasket 1
22
2.0" Side Mount Valve Bottom Body (White) 1
Sight Glass With O-Ring 1
O-Ring for Union Tale 1
1
2.0" Union Tale (White)
2.0" Union Nut (Black) 2
O-Ring for Plug 1
2.0" Side Mount Valve Plug (White) 2
2.0" Elbow Tube (White)183mm 1
1
2.0" Union Adaptor (Metric)
3-4
Description Qty
Nut with washer 12
Air Release Valve with Oring 1
Maximum 40PSI Indication, Stainless Steel Casing 1
Lid (Grey Colour) 1
Filter Neck Gasket 1
S700B Filter Tank 1
Filter Tank with Base for S800 1
Filter Tank with Base for S900 1
The Inner Tank System for S700 (B) 1
The Inner Tank System for S800 1
The Inner Tank System for S900 1
2.0" Tank System Support 1
O-Ring for Inlet & Outlet 2
6 Way 2" Valve with Piping Kit, 2" union set x 3 and
1
pressure gauge (White)
Laterals (185mm) 8
Laterals (233mm) 8
Water Drain Set 1
21-28inch Filter Base 1
32-40 inch Filter Base 1
9 10 11
12
14
8
16
15
13
17
18
19
24
25
23
21
26
27