Advertisement
3)
Install the valve.
Tighten the Ring Lock Nut by 2 handles and make sure the nut is "sand free" on its thread.
a)
Carefully screw the T-shape Exhaust Switch onto the filter lid and make sure there do not over-tighten.
b Ensure T-Shape Exhaust switch is tight fit to filter lid and turn it easily.
)
4) Connect pump to control valve opening marked PUMP.
5) Make return to pool pipe connection to control valve opening marked RETURN and complete other
necessary plumbing connections, suction lines to pump, waste, etc.
6) Make electrical connections to pump per pump instructions.
7) To prevent water leakage, be sure all pipe connections are right.
MAIN DIMENSION
DIMENSION TABLE
Valve Port
High
Diameter
Model
Size
mm
mm
Inch
A
B
1.5 "
S450R
760
455
825
535
1.5 "
S500R
1.5 "
S650R
890
635
1.5 "
S700R
920
723
INSTALL/START-UP OF FILTER
1) Be sure correct amount of filter media sand is in tank and that all connections have been made and are secure.
2) Depress control valve handle and rotate to BACKWASH position. (To prevent damage to control valve seal,
always depress handle before turning.)
3) Prime and start pump according to pump instructions (be sure all suction and return lines are open), allowing the
filter tank to fill with water. Once water is flowing out of the waste line, run the pump for at least 1 minute. The
initial back-washing of the filter is recommended to remove any impurities or fine sand particles in the sand
media.
4) Turn pump off and set valve to RINSE position. Start pump and operate until water in sight glass is clear, about 1/2
to 1 minute. Turn pump off and set valve to FILTER position and restart pump.The filter is now operating in the
normal filter mode, filtering dirt particles from the pool water.
5) Adjust pool suction and return valves to achieve desired flow. Check system and filter for water leaks and
tighten connections, bolts, nuts, as required.
6) Note the initial pressure gauge reading when the filter is clean. (It will vary from pool to pool depending upon the
pump and general piping system.)
As the filter removes dirt and impurities from the pool water, the
accumulation in the filter will cause the pressure to rise and flow to diminish. When the pressure gauge reading is
1.5 bar, higher than the initial "clean" pressure you noted, it is time to backwash the filter (see BACKWASH under
filter and control valve functions).
NOTE: During initial clean-up of the pool water it may be necessary to backwash frequently due to the unusually
heavy initial dirt load in the water.
Sand
Kg
45
85
145
210
B
2-4
A
REPLACEMENT PARTS OF MULTIPORT VALVE
Key No.
Part No.
1
01013002
Handle (Small)
2
03018008
Pin for Handle
3
01181001
Washer for Handle
89281203
M6×25 Screw with Nut for Camber Lid
4
89280107
M6*30 Screw with Nut for Standard Lid
5
01013004
1.5"Side Mount Valve Standard Lid (Black)
6
02011022
O-Ring for 1.5" Valve Rotor
7
01181002
Washer for Spring
8
02011002
O-Ring for 1.5" Valve Lid
9
03014001
Spring for 1.5" Simd Mount Valve
10
01021001
1.5" Valve Rotor
11
02311002
Spider Gasket
12
01013009
1.5" Side Mount Valve Bottom Body (Black)
13
01111048
Connector for Pressure Gauge/Stopper
14
89021303
Drain Plug with O-ring
15
06011029
Oil Pressure Gauge With O-ring (40psi)
16
02011151
O-Ring
17
01013018
1.5"Union Tale (Black)
18
01013017
1.5" Union Nut (Black)
19
89280104
Sight Glass with O-Ring
20
01013120
1.5" Side Mount Valve Plug (Black)
01013117
1.5" Elbow Tube (Black) 175mm
21
01013116
1.5" Elbow Tube (Black) 120mm
22
01171002
1.5" Union Adaptor (Metric)
23
01013015
1.5"Connector with External Thread(Black)
24
02011003
O-Ring for Union Adaptor
25
01171153
1.5"Union Adaptor
REPLACEMENT PARTS OF FILTER
Key No.
Part No.
1
01271012
Ringlock Nut
2
01021004
Spanner for RingLock
3
06011029
Maximum 40PSI Indication, Stainless Steel Casing
4
89014027
T-Shape Exhuaust Switch
5
01201020
Cover
6
02010033
O-Ring for Cover
7
89010648
S450 RingLocK Filter tank
7
89010649
S500 RingLocK Filter tank
7
89010650
S650 RingLocK Filter tank
7
89010651
S700 RingLocK Filter tank
7
89011204
S700(B) RingLocK Filter tank
8
89011309
The inner tank system for S450R
8
89011310
The inner tank system for S500R
8
89011311
The inner tank system for S650R
8
89011312
The inner tank system for S700R
8
89011203
The inner tank system for S700R(B)
9
01111046
1.5"Tank System Support
9
01101065
2.0"Tank System Support
10
02011003
O-Ring for 1.5" adaptor
10
02020016
O-Ring for Connector
6 Way 1.5" Valve with Piping Kit, 1.5" union set x 3
11
88280810B
and pressure gauge (Black)
6 Way 2" Valve with Piping Kit, 2" union set x 3 and
11
88280813B
pressure gauge (Black)
12
01172007
Laterals(115mm)
12
01172008
Laterals (126mm)
12
01172010
Laterals (185mm)
13
01111059
16-21inch Filter Base
13
01111062
21-28inch Filter Base
14
89010107
Water Drain Set
Product Description
Qty
1
1
1
6
2
6
1
4
2
1
1
6
1
8
1
9
1
11
1
1
12
1
1
16
23
24
5
25
18
1
5
1
1
1
1
1
3
3
3
3-4
Description
Qty
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
1
8
8
8
1
1
1
1
3
5
7
10
15
13
14
16
17
18
19
16
20
21
22
18
Advertisement
