Advertisement
3)
Install the valve.
Tighten the Ring Lock Nut by 2 handles and make sure the nut is "sand free" on its thread.
a)
Carefully screw the T-shape Exhaust Switch onto the filter lid and make sure there do not over-tighten.
b Ensure T-Shape Exhaust switch is tight fit to filter lid and turn it easily.
)
4) Connect pump to control valve opening marked PUMP.
5) Make return to pool pipe connection to control valve opening marked RETURN and complete other
necessary plumbing connections, suction lines to pump, waste, etc.
6) Make electrical connections to pump per pump instructions.
7) To prevent water leakage, be sure all pipe connections are right.
MAIN DIMENSION
DIMENSION TABLE
High
Diameter
Valve Port
Model
mm
mm
Size
A
B
Inch
S700R(B)
920
723
2"
S800R
1020
820
2"
S900R
1130
920
2"
INSTALL/START-UP OF FILTER
1) Be sure correct amount of filter media sand is in tank and that all connections have been made and are secure.
2) Depress control valve handle and rotate to BACKWASH position. (To prevent damage to control valve seal,
always depress handle before turning.)
3) Prime and start pump according to pump instructions (be sure all suction and return lines are open), allowing the
filter tank to fill with water. Once water is flowing out of the waste line, run the pump for at least 1 minute. The
initial back-washing of the filter is recommended to remove any impurities or fine sand particles in the sand
media.
4) Turn pump off and set valve to RINSE position. Start pump and operate until water in sight glass is clear, about 1/2
to 1 minute. Turn pump off and set valve to FILTER position and restart pump.The filter is now operating in the
normal filter mode, filtering dirt particles from the pool water.
5) Adjust pool suction and return valves to achieve desired flow. Check system and filter for water leaks and
tighten connections, bolts, nuts, as required.
6) Note the initial pressure gauge reading when the filter is clean. (It will vary from pool to pool depending upon the
pump and general piping system.)
As the filter removes dirt and impurities from the pool water, the
accumulation in the filter will cause the pressure to rise and flow to diminish. When the pressure gauge reading is
1.5 bar, higher than the initial "clean" pressure you noted, it is time to backwash the filter (see BACKWASH under
filter and control valve functions).
NOTE: During initial clean-up of the pool water it may be necessary to backwash frequently due to the unusually
heavy initial dirt load in the water.
Sand
Kg
215
355
470
B
2-4
A
Note:12* S800R should have 8pcs of Laterals (185mm)
12* S900R should have 8pcs of Laterals (233mm)
Key No.
Part No.
Handle (Big)
1
01013003
2
03018008
Pin for Handle
3
01181027
Washer for Handle
4
01013022
2.0" Side Mount Valve Rotundity Lid (Black)
5
89280301
M6*32 Screw with Nut
6
01111048
Connector for Pressure Gauge/Stopper
7
89021303
Drain Plug with O'Ring
8
06011029
Oil Pressure Gauge With O-ring (40psi)
9
02020016
O-Ring for 2.0"Union
10
01013031
2.0"Connector(Black)
2.0"Union (A/E)
11
01171154
12
01013032
2.0"Union Nut(Black)
13
02011009
O-Ring for 2.0" Valve Lid
14
01181002
Washer for spring
15
02011022
O-Ring for 2.0" Valve Rotor
16
03014014
Spring
17
01021002
2.0" Valve Rotor
18
02311003
Spider Gasket
19
01013026
2.0" Side Mount Valve Bottom Body (Black)
20
89280104
Sight Glass With O-Ring
21
02011011
O-Ring for Union Tale
2.0" Union Tale (Black)
22
01013099
23
01013034
2.0" Union Nut (Black)
24
02020017
O-Ring for Plug
25
01013101
2.0" Side Mount Valve Plug (Black)
26
01013118
2.0" Elbow Tube (Black)183mm
2.0" Union Adaptor (Metric)
27
01171035
REPLACEMENT PARTS OF FILTER
Key No.
Part No.
1
01021004
2
01271013
3
06011029
4
89014027
5
01201020
6
02011036
7
89011212
7
89011213
8
89011203
8
89011210
8
89011211
9
01101065
10
02020016
11
88280813B
12*
01172010
12*
01172011
13
01112038
14
89010107
REPLACEMENT PARTS OF MULTIPORT VALVE
Product Description
Qty
1
1
1
2
1
3
1
10
5
1
4
1
6
1
7
8
8
3
3
3
1
1
2
1
20
1
1
22
1
1
1
1
2
1
2
1
1
3-4
Description
Qty
Spanner for RingLock
1
2.0" Ringlock Nut
1
Oil Pressure Gauge With O-ring
1
T-Shape Exhuaust Switch
1
Cover
1
O-Ring for Cover
1
S800 RINGLOCK Filter Tank With Base
1
S900 RINGLOCK Filter Tank With Base
1
The inner tank system for S700R(B)
1
The inner tank system for S800( R)(B)
1
The inner tank system for S900( R)(B)
1
2.0"Tank System Support
1
2.0" O-Ring for Connector
1
6 Way 2" Valve with Piping Kit, 2" union
1
set x 3 and pressure gauge (Black)
Laterals (185mm) For S800R
8
Laterals (233mm) For S900R
8
32-40 inch Filter Base
1
Water Drain set
1
9
10
11
12
14
16
15
13
17
18
19
24
25
21
23
26
27
Advertisement
