Glendinning HOSEMASTER MODEL-S Installation & Operation Instructions

P/N DESCRIPTION
05550-08-X Hosemaster Model-S™ (Base unit / sprayer optional)
NOTE: must specify type of mounting bracket (U=u-bracket, S=side bracket,
E=edge bracket)
05550-16-X Hosemaster Model-S™ (Base unit / sprayer optional)
NOTE: must specify type of mounting bracket (U=u-bracket, S=side bracket,
E=edge bracket)
05551-16-X Hosemaster Model-D™ (Base unit w/ deck wash sprayer & hose adapter fitting)
NOTE: must specify type of mounting bracket (U=u-bracket, S=side bracket,
E=edge bracket)
05551-18-X Hosemaster Model-D™ (Base unit w/ deck wash sprayer & hose adapter fitting)
NOTE: must specify type of mounting bracket (U=u-bracket, S=side bracket,
E=edge bracket)
99582-DK Deck sprayer attachment with thru-hull fitting
NOTE: used with U-bracket mounting assembly only.
99582-REC Long sprayer attachment with hatch assembly
99582-SN Short sprayer attachment with hatch assembly
99593 Deck wash sprayer attachment with hose adapter fitting
NOTE 1: The deck wash sprayer attachment is included when you purchase the
Hosemaster Model-D™ (PN-05551-XX-X).
NOTE 2: The deck wash sprayer attachment can also be used with any Hosemas-
ter Model-S™ (PN-05550-XX-X) when purchased separately.
L
IMITED
PRODUCT(S) COVERED BY THIS LIMITED WARRANTY: HOSEMASTER — MODEL-S, MODEL-D
1. GLENDINNING MARINE PRODUCTS, INC. warrants to the original consumer purchaser that the Hosemaster will be free from defects in material and workmanship under normal use and service for a period of one (1) year from
the date of purchase.
2. This LIMITED WARRANTY applies to defects in material and workmanship. It does not apply to chromeplated or anodized finish or to power cable damage caused by inadequate cable storage area or installation not in accordance
with GLENDINNING MARINE PRODUCTS, INC. specifications.
3. This LIMITED WARRANTY is void if the product has been damaged by accident or unreasonable use, neglect, improper installation, or other causes not arising out of defects in material or workmanship.
4. To obtain performance of this LIMITED WARRANTY obligation the original purchaser should contact GLENDINNING MARINE PRODUCTS, INC. for instructions concerning removal and shipping of the defective component. Upon
compliance of the foregoing procedure all warranted defects will be repaired, or at GLENDINNING MARINE PRODUCTS, INC. option, the complete unit replaced and returned to the consumer, shipping charges prepaid.
5. GLENDINNING MARINE PRODUCTS, INC. does not assume the costs of removal and/or installation of the product or any other incidental costs which may arise as a result of any defect in materials or workmanship.
THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES. ANY WARRANTY IMPLIED BY LAW INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS, IS IN EFFECT ONLY FOR THE DURATION OF
THE EXPRESS WARRANTIES SET FORTH IN THE FIRST PARAGRAPH ABOVE. NO REPRESENTATIVE OR PERSON IS AUTHORIZED TO GIVE ANY OTHER WARRANTY OR TO ASSUME FOR GLENDINNING MARINE
PRODUCTS, INC. ANY OTHER LIABILITY IN CONNECTION WITH THE SALE OF IT'S PRODUCTS. GLENDINNING MARINE PRODUCTS, INC. WILL NOT BE LIABLE FOR ANY CONSEQUENTIAL DAMAGES RESULTING FROM
THE USE OR INSTALLATION OF IT'S PRODUCTS.
740 Century Circle • Conway, SC 29526 • P: 843-399-6146 • F: 843-399-5005
HOSE LENGTH
8 ft.
[2.4 meters]
16 ft.
[4.9 meters]
16 ft.
[4.9 meters]
18 ft.
[5.5 meters]
W
ARRANTY
www.glendinningprods.com
SML-HMS-INSTAL
HOSEMASTER MODEL-S™ & MODEL-D™
INSTALLATION & OPERATION INSTRUCTIONS
∆ NOTE: Hosemater Model-S™ or Model-D™ not approved for potable water applications ∆
BEFORE INSTALLING THE HOSEMASTER MODEL-S™ OR MODEL-D™:
Careful consideration should be given to where the sprayer nozzle will be installed. Determine if sufficient space is available below the sprayer nozzle
where the base unit will be installed. MAKE SURE to allow a minimum of 1.60" space on the 1/2" NPT outlet side of the unit for the installation of water
connection hardware to the Hosemaster Model-S™ or Model-D™.
Ø 10.25
[260mm]
THERE ARE 4 DIFFERENT WAYS TO MOUNT YOUR HOSEMASTER MODEL-S OR MODEL-D:
1. U-BRACKET INSTALLATION (Fig. 1)
The U-Bracket is to be used with the thru-hull deck fitting (PN 99582-DK).
1) Attach the U-Bracket to the Hosemaster base unit by placing over the studs
of the roller guide assembly. Attach the lock nuts and washers and tighten.
2) Using a 1.25" bit, drill a hole where you have determined sufficient space is
available for the installation of the Hosemaster.
2) Remove the nut and gasket from the thru-hull fitting and insert thru-hull fitting
into the hole.
3) Pull out a length of hose and insert the hose through the nut, mounting bracket
and the gasket (in that order) onto the hose before inserting hose into the thru-hull
fitting. Thread nut onto thru-hull fitting shaft and tighten.
4) Connect the sprayer attachment onto the sprayer adapter and pull and release
hose to retract length of hose so that sprayer attachment fits into thru-hull fitting.
5) Connect a length of hose from the water source to the 1/2" NPT inlet connector
located on the side of the reel. Hold nut on opposite side when tightening
inlet fitting.
Water Connection
hardware
(not included)
11.50
[292mm]
Allow
6.00 [152mm]
for water supply
connection
3.625
[92mm]
.864
[22mm]
Thru-hull
deck fitting
Gasket
Hose
U-bracket
lock nuts
Fig. 1
U-Bracket
Installation with
thru-hull deck
fitting
Deck
Sprayer
Adapter
Nut