Telco Systems AC-211 User Manual

Access 211 voip gateway

Advertisement

A C C E S S 2 1 1 V o I P
G A T E W A Y
( A C - 2 1 1 )
U S E R G U I D E
MN100129 Rev A01

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AC-211 and is the answer not in the manual?

Questions and answers

Summary of Contents for Telco Systems AC-211

  • Page 1 A C C E S S 2 1 1 V o I P G A T E W A Y ( A C - 2 1 1 ) U S E R G U I D E MN100129 Rev A01...
  • Page 2 A C C E S S 2 1 1 V O I P G A T E W A Y ( A C - 2 1 1 ) U S E R G U I D E Revision History Revision Date Description April 01, 2004...
  • Page 3: Table Of Contents

    A C C E S S 2 1 1 V O I P G A T E W A Y ( A C - 2 1 1 ) U S E R G U I D E Table of Contents INTRODUCTION ..........................
  • Page 4: Introduction

    G U I D E Introduction Thank you for purchasing this product. We at Telco Systems are confident that you will obtain full satisfaction from your new Access 211 VoIP gateway. Please read this guide carefully in order to make use of all the advanced features provided by the Access 211. Should you encounter any difficulties, do not hesitate to contact us by E-mail, phone, or via our Web site.
  • Page 5: Product Overview

    A C C E S S 2 1 1 V O I P G A T E W A Y ( A C - 2 1 1 ) U S E R G U I D E Product Overview The Access-211 is a terminal Voice-over-IP (VoIP) WAN gateway device with two VoIP ports, which can be used to connect one or two independent analog telephone or Fax lines over the Internet or Intranet.
  • Page 6: The Rear Panel

    A C C E S S 2 1 1 V O I P G A T E W A Y ( A C - 2 1 1 ) U S E R G U I D E The rear panel contains the phone connectors, the LAN and WAN connectors and the input DC power connector, as shown in the following figure.
  • Page 7: Installation

    Two push-button telephones with DTMF (tone signal) capability (not supplied). • An AC/5VDC power adapter (supplied). The AC-211 must be powered by an external UL listed limited power source or Class II power source (AC/DC adapter), rated input: 100 -250 V, 47-63Hz, 0.2A, output: 5VDC – 2A.
  • Page 8: T O Install Your Access 211 V Oip Gateway With A Single Pc

    A C C E S S 2 1 1 V O I P G A T E W A Y ( A C - 2 1 1 ) U S E R G U I D E 1. Unpack the Access 211 Gateway unit. 2.
  • Page 9 Enabling Point-to-Point Protocol over Ethernet (PPPoE) on page 15, and disable PPPoE on your PC. 10. Wait for the Voice LED on the AC-211 front panel to glow, indicating connection to your Internet and VoIP providers. It may take a minute or two for these connections to be established.
  • Page 10: T O Install Your Access 211 V Oip Gateway With A Home Network

    Choose a location that is near the devices to be connected and close to an electrical outlet. Connect the WAN port on the AC-211 rear panel to an open Ethernet LAN port on your router with a supplied Ethernet 10/100BaseTX (RJ-45) cable, in accordance with the...
  • Page 11 U S E R G U I D E Wait for the Voice LED on the AC-211 front panel to glow, indicating connection to your Internet and VoIP providers. It may take a minute or two for these connections to be established.
  • Page 12: Advanced Configuration Via The Web

    A C C E S S 2 1 1 V O I P G A T E W A Y ( A C - 2 1 1 ) U S E R G U I D E Advanced Configuration via the Web If you need to configure your Access-211 Gateway, proceed as follows.
  • Page 13 A C C E S S 2 1 1 V O I P G A T E W A Y ( A C - 2 1 1 ) U S E R G U I D E 4. In the vertical menu bar on the left, select WAN. The WAN Status page appears: Figure 2: WAN Status Page 5.
  • Page 14 A C C E S S 2 1 1 V O I P G A T E W A Y ( A C - 2 1 1 ) U S E R G U I D E Figure 3: WAN Configuration Page Select either of the following options.
  • Page 15: Enabling Point - To -Point Protocol Over Ethernet (Ppp O E)

    Completing the Access 211 Gateway Configuration on page 21). If you have a DSL modem and are NOT using a router between the AC-211 and the modem, configure PPPoE as follows: 1. In the horizontal menu bar of the WAN page, select PPPoE.
  • Page 16: Mac Spoofing

    MAC spoofing may be required in the case that your broadband provider associates a particular service to a specific device (e.g. your computer). To override the AC-211's MAC address that you supplied to you broadband provider In the horizontal menu bar of the WAN page, select MAC Spoofing.
  • Page 17: Configuring Lan Settings

    A C C E S S 2 1 1 V O I P G A T E W A Y ( A C - 2 1 1 ) U S E R G U I D E Figure 6: LAN Configuration Page Configuring LAN Settings To configure LAN settings, broadcast and multicast traffic limits and/or rate control, proceed as follows:...
  • Page 18: Dhcp Server Configuration

    A C C E S S 2 1 1 V O I P G A T E W A Y ( A C - 2 1 1 ) U S E R G U I D E ISP is considerably lower than the download link from the ISP. Setting the Rate control parameters will insure that even while running heavy bandwidth applications on the devices connected to LAN port the voice quality is preserved.
  • Page 19 A C C E S S 2 1 1 V O I P G A T E W A Y ( A C - 2 1 1 ) U S E R G U I D E To enable the DHCP Server, select the Server Settings Enabled option. Fill in the following fields: •...
  • Page 20: Port Forwarding

    A C C E S S 2 1 1 V O I P G A T E W A Y ( A C - 2 1 1 ) U S E R G U I D E Figure 8: DHCP Client Table Page Port Forwarding Port forwarding associates local port ranges to local P addresses in order to enable external network users to access local devices, without the need for the local servers to first access the global...
  • Page 21: Completing The Access 211 Gateway Configuration

    A C C E S S 2 1 1 V O I P G A T E W A Y ( A C - 2 1 1 ) U S E R G U I D E Figure 9: Port Forwarding Configuration Page 2.
  • Page 22 A C C E S S 2 1 1 V O I P G A T E W A Y ( A C - 2 1 1 ) U S E R G U I D E Figure 10: Reset Page MN100129 Rev A01...
  • Page 23: Using The Access 211 Gateway

    A C C E S S 2 1 1 V O I P G A T E W A Y ( A C - 2 1 1 ) U S E R G U I D E Using the Access 211 Gateway To make a call, connect to the Internet or Intranet with a VoIP service.
  • Page 24: Hold

    A C C E S S 2 1 1 V O I P G A T E W A Y ( A C - 2 1 1 ) U S E R G U I D E The phone will ring both at the destination number and at your line. By picking up the handset, the callee at the destination number will be engaged in the call with the original caller.
  • Page 25: Transfer Call

    A C C E S S 2 1 1 V O I P G A T E W A Y ( A C - 2 1 1 ) U S E R G U I D E Transfer call To transfer a call that you are receiving to another number, dial flash + 4 + destination number and put the handset down.
  • Page 26: Troubleshooting

    No dial tone Verify that the phone line is securely plugged into the Phone1 or Phone2 port. Verify that the WAN Link/Act LED on th AC-211 front panel is active. If it is not, check that the WAN cable is properly connected.
  • Page 27: Specifications

    A C C E S S 2 1 1 V O I P G A T E W A Y ( A C - 2 1 1 ) U S E R G U I D E Specifications Dimensions 4.75”(W) x 7.36”(L) x 1.77”(H) 120(W) x 187(L) x 45(H) mm Weight: 1.32 lbs (0.6 kg)

Table of Contents