Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for CHIEF AN1 Series
- Page 1 I N S T A L L A T I O N I N S T R U C T I O N S All-in-One System Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description French Product Description AN1 Series...
-
Page 2: Important Safety Instructions
IMPORTANT ! : The AN1 Series mounts are designed to be Chief® is a registered trademark of Milestone AV Technologies. used ONLY with the Epson BrightLink Pro 1410Wi projector. - Page 3 Installation Instructions AN1 Series DIMENSIONS DIMENSIONS: INCHES [MILLIMETERS]...
-
Page 4: Installation Instructions
AN1 Series Installation Instructions LEGEND Tighten Fastener Pencil Mark Apretar elemento de fijación Marcar con lápiz Befestigungsteil festziehen Stiftmarkierung Apertar fixador Marcar com lápis Serrare il fissaggio Segno a matita Bevestiging vastdraaien Potloodmerkteken Serrez les fixations Marquage au crayon Loosen Fastener Drill Hole Aflojar elemento de fijación... -
Page 5: Tools Required For Installation
Installation Instructions AN1 Series TOOLS REQUIRED FOR INSTALLATION 1/8" (wood) 7/16" 1/2" (drywall) 8mm (concrete) 6mm (concrete - AF6 toggler) PARTS D (4) 1/4" C (4) A (4) 1/4-20 x 1-3/4" B (4) 1/4 x 2-1/2" Hilti Hud-L #8 x 60... -
Page 6: Installation
AN1 Series Installation Instructions INSTALLATION Determining Location 2.75” 6.50” 46.00” HEIGHT FROM FLOOR 73.00” FLOOR Figure 1 Table 1: Fastener Information Determine desired height of screen (measured from floor). (See Figure 1) Determine desired center of screen. (See Figure 1) - Page 7 Installation Instructions AN1 Series Installing Wall Bracket / Boom Projector Mount Install and tighten two 10-24 x 3/8" Phillips cap head screws (H) through upper arm of boom projector mount (V) into Install one fastener (See Table 1) into previously drilled vertical portion of wall bracket (S).
-
Page 8: Attaching Screen
AN1 Series Installation Instructions Attaching Screen Hang screen assembly (R) onto wall bracket (S) using pre-installed bracket on back of screen assembly. (See Figure 5) Center screen assembly on wall bracket, matching pieces of tape on top of screen with edges of boom mount on wall bracket. -
Page 9: Installing Projector
Installation Instructions AN1 Series Installing Projector Installing Control Housing Attach projector interface (T) to projector using four Open door on control panel assembly (U). M4 x 10mm Phillips cap head screws (J). (See Figure 8) Insert edges of control panel assembly (U) into groove in screen frame, with tab placed behind screen. - Page 10 AN1 Series Installation Instructions Installing Control Pad Remove top cover from control pad. (See Figure 11) Bosses Open lower cover on control pad. (See Figure 11) Insert control pad into control housing (U) by sliding it up under tabs inside housing. (See Figure 11)
- Page 11 Installation Instructions AN1 Series Projector Adjustments Yaw Adjustment Loosen yaw adjustment locking screw using a #2 Phillips screwdriver. (See Figure 13) Turn yaw micro-adjustment screw right or left using a #2 Phillips screwdriver until image is properly aligned on target.
- Page 12 AN1 Series Installation Instructions Micro Adjustment If required, turn the micro adjust fastener clockwise to extend projector further from wall. (See Figure 16) If required, turn the micro adjust fastener counterclockwise to retract projector closer to wall. (BB) Extend Bracket...
- Page 13 Installation Instructions AN1 Series FASTENER INSTALLATION METHODS Steel stud NOTE: Refer to Table 1 for appropriate hardware and pilot hole (if present) sizes for various wall types. Drywall Steel Stud / Drywall Plastic cap Hold metal channel on anchor (E) flat alongside plastic straps and slide channel through hole.
- Page 14 AN1 Series Installation Instructions Concrete NOTE: Refer to Table 1 for appropriate hardware and pilot hole sizes for various wall types. Install an anchor (B) into each pilot hole using a hammer, making sure that the anchor is flush with the wall.
- Page 15 Installation Instructions AN1 Series...
- Page 16 Europe A Franklinstraat 14, 6003 DK Weert, Netherlands P +31 (0) 495 580 852 F +31 (0) 495 580 845 Chief Manufacturing, a products division Asia Pacific A Office No. 1 on 12/F, Shatin Galleria of Milestone AV Technologies 18-24 Shan Mei Street...
Need help?
Do you have a question about the AN1 Series and is the answer not in the manual?
Questions and answers