Huawei RC2843002 User Manual

Features and Functions
Huawei Remote
Use the remote control's keys to perform
Control User Guide
actions described below.
Warning: Please do not point
the IR LED to eyes directly.
Installing Batteries
The remote control requires 2 AAA size
To enter STB setup
(1.5V) batteries.
mode.
1. On the back of the remote control, press
When a valid TV code is
the battery cover tab, lift and remove the
programmed, to enter
battery cover.
TV setup mode.
2. Insert 2 AAA-size batteries, matching
When a valid TV code
the (+) and (–) symbols shown on the
is programmed, to
battery compartment.
power off or on TV.
3. Put back the battery cover. Test the
remote control by press and hold Setup
To enter a number or
key for 3 seconds, the Red LED
select a channel
indicator at top right will blink twice.
number.
RF Pairing with STB
To reserve for future
use.
Method of pairing:
When a valid TV code
1. Press Setup key until the LED indicator
is programmed, to
blinks twice.
select TV input
2. Press Info key until 3 random digits are
source.
displayed on TV screen, the LED
indicator turns on.
To enter STB menu.
3. Enter the 3 random digits numeric
displayed on TV screen to pair the
To enter STB guide. remote control with target STB. When
each digit key has been pressed and
released, the LED indicator acts a
reverse blink.
To navigate through
4. The LED indicator will blink twice once
display menu.
the remote control has been paired with
the target successfully. Otherwise if
pairing is unsuccessful, the LED
To confirm an action.
indicator will blink 5 times and the
remote control returns to user mode.
To turn STB audio off
or on.
Notes:
When a valid TV code
is programmed, to turn
• In Step 3, STB will display 3 random
TV audio off or on.
digits on TV screen, you need press first
To increase/decrease
digit within 8 seconds, for second and
volume on the STB.
third digits, you have to press the digit
When a valid TV code
within 4 seconds.
is programmed, these
• If timeout occurs, the LED indicator will
keys will control the
blink 5 times and the remote control
TV volume.
returns to user mode.
• You also can interrupt the pairing during
To recall STB previous
channel. Validation Process by pressing Info key.
• If pairing is interrupted by pressing Info
key, or pairing failed, the LED indicator
To select
will blink 5 times, and the remote control
previous/next channel
returns to user mode.
on the STB.
• Pairing distance not more than 2 meters.
To display program Programming to control TV
information or other
device
menu options.
There are two ways to do this. If your
To exit STB menu.
device is listed in the Code List at the end
of this Manual, you can use section A. If
To switch between
your device is not listed, you will need to
different languages
use section B.
and audio options,
when available on the
A. Manually
STB.
1. Press and hold the Setup key until the
LED indicator blinks twice.
2. Enter the appropriate 4-digit setup code
for TV (from the Code List) by pressing
• If 15 seconds timeout occurs, the LED
the number keys (0-9) on the remote indicator blinks 5 times and returns to
control. user mode.
• If the LED indicator blinks twice, a
B. Change volume control from STB to
correct code has been entered.
TV
• If the LED indicator blinks 5 times, an 1. Press and hold the Setup key until the
LED indicator blinks twice.
invalid code has been entered. Start
2. Enter 993 by pressing the number keys
over at step 1.
on the remote control, the LED indicator
will blink twice.
Notes:
3. Press and release number key 2, the
If you are interrupted while you are
LED indicator will blink twice.
programming, the remote control may
timeout before you complete the code
• If an invalid code has been entered at
setup and you will need to start over.
step 2, the LED indicator will blink 5
This is indicated by the LED indicator
times and return to user mode. Start
blink 5 times, and returns to user mode.
over at step 1.
• If 15 seconds timeout occurs, the LED
B. Using the Automatic Search
indicator will blink 5 times and return to
1. Press and hold the Setup key until the
user mode.
LED indicator blinks twice.
2. Enter 991 by pressing the number keys
Check TV Code been set to the
on the remote control, the LED indicator
remote
will blink twice.
3. Press and hold the key, until the
If you need to check the TV code that been
TV turns off. Release the key.
set to the remote, you can follow the steps
4. You can control TV with the 5 keys
which are TV power, Input, Mute, below.
Volume Up and Volume Down.
1. Press and hold the Setup key until the
5. Press OK and EXIT key together to exit
automatic search mode. LED indicator blinks twice.
2. Enter 990 by pressing the number keys
on the remote control, the LED indicator
• For step 3, code search will start 1.5
will blink twice.
seconds after press and hold the TV
3. To view the first code, Press number key
power key.
1, release the key and count on the
• At step 4, you have to short press the
number of LED indicator blink. (For
TV power key. For long press of more
example, 3 blinks, the code digit is 3)
than 1.5 seconds will trigger remote to
Note: If code digit is 0, then the LED
automatic search for next code. Until
indicator will not blink.
step 5 which exit the automatic search
4. Repeat step 3 for second, third and
mode.
fourth digit. Press number key 2 for
• If you want to continue to automatic
second digit; Press number key 3 for
search for next code, repeat step 3.
third digit; Press number key 4 for fourth
• If an invalid code has been entered at
digit.
step 2, the LED indicator will blink 5
times and return to user mode. Start
• If an invalid code has been entered at
over at step 1.
step 2, the LED indicator will blink 5
times and return to user mode. Start
Changing Volume control
over at step 1.
The remote is set to control volume level of
Resetting TV Configuration
STB. Once a valid TV code is
Settings
programmed, the volume keys will control
the TV volume.
1. Press and hold the Setup key until the
LED indicator blinks twice.
A. Change volume control from TV to
2. Enter 996 by pressing the number keys
STB
on the remote control, the LED indicator
1. Press and hold the Setup key until the
LED indicator blinks twice. will blink twice.
2. Enter 993 by pressing the number keys
on the remote control, the LED indicator • If an invalid code has been entered at
will blink twice. step 2, the LED indicator will blink 5
3. Press and release number key 1, the times and return to user mode. Start
LED indicator will blink twice. over at step 1.
• If an invalid code has been entered at
Care of your Remote Control
step 2, the LED indicator will blink 5
times and return to user mode. Start
Do not use your Remote Control in other
over at step 1.
ways that it was designed for. Prevent
water or other liquids from damaging your
Remote Control.
Check your batteries to ensure no leaking
batteries are used. For optimum
performance, change the batteries after 6
to 9 months.
Troubleshooting
1. The LED indicator is off when you press
the remote keys:
• Check batteries whether are correctly
installed or not.
• Change batteries if needed.
2. The LED indicator blinks but the remote
control cannot function when you press
the remote keys:
• Check the power of STB.
• Power Off then On the STB, and try to
do pairing of remote and receiver.
FCC ID: RCSRC2843003
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) this device
may not cause harmful interference, and
(2) this device must accept any
interference received, including
interference that may cause undesired
operation.
You are cautioned that changes or
modifications not expressly approved by
the party responsible for compliance could
void your authority to operate this
equipment.