Summary of Contents for Jelight UVO-CLEANER
- Page 1 Jelight Company, Inc. 2 Mason Irvine, CA 92618 U.S.A Tel: +1(949) 380-8774 Fax +1(949) 768-9457 ® UVO-CLEANER Model 18, 24, 30 Instruction Manual Original Instructions REV. E...
-
Page 2: Table Of Contents
Jelight Company, Inc. 2 Mason Irvine, CA 92618 U.S.A Tel: +1(949) 380-8774 Fax +1(949) 768-9457 Table of Contents Safety Guide ............3 Introduction ............4 Specifications ............5 Machine Description ..........6 Parts Assembly ............9 System Setup ............10 Lamp Installation ........... -
Page 3: Safety Guide
Jelight Company, Inc. 2 Mason Irvine, CA 92618 U.S.A Tel: +1(949) 380-8774 Fax +1(949) 768-9457 Safety Guide WARNING! Hazardous Voltage Do not remove the cover while the equipment is plugged to an electrical outlet; risk of electric shock. WARNING! Inhalation Hazard Ozone is produced by this equipment during operation and appropriate ventilation must be provided for exhaust purposes. -
Page 4: Introduction
By placing properly pre-cleaned samples within five millimeters of ozone producing UV source, ® such as the low pressure mercury vapor grid lamp inside the UVO-Cleaner , near atomically clean surfaces can be achieved in less than one minute. In addition, this process does not damage any sensitive device structures of MOS gate oxide. -
Page 5: Specifications
Jelight Company, Inc. 2 Mason Irvine, CA 92618 U.S.A Tel: +1(949) 380-8774 Fax +1(949) 768-9457 Specifications Outer Dimensions without Ozone Filter Length Width Height Media Inlet Port Exhaust Port 11.50” [292mm] 9.25” [235mm] 8.50” [216mm] Ø 0.375” [9.5mm] Ø 1.0” [25.4mm]... -
Page 6: Machine Description
Jelight Company, Inc. 2 Mason Irvine, CA 92618 U.S.A Tel: +1(949) 380-8774 Fax +1(949) 768-9457 Machine Description Front Panel Lamp Indicator Handle Hinge Latch Timer Indicator Set/Display (Timer) On-Off Switch Emergency Stop Button Timer Power-On Stop Indicator Start/ Resume Timer... - Page 7 Jelight Company, Inc. 2 Mason Irvine, CA 92618 U.S.A Tel: +1(949) 380-8774 Fax +1(949) 768-9457 Machine Description (Continued) Rear Panel Lamp Media Inlet Cable Port Exhaust Port Socket Outlet Fuse Holder (Blower) AC Power Ventilation Cord Monitor (optional on some models only) FIG.
- Page 8 Jelight Company, Inc. 2 Mason Irvine, CA 92618 U.S.A Tel: +1(949) 380-8774 Fax +1(949) 768-9457 Machine Description (Continued) Interior Lid Latch (Upper) Lamp Assembly Lid Switch Actuator Optional Ozone Filter and Lamp Blower Assembly Terminals shown mounted to Exhaust Port...
-
Page 9: Parts Assembly
Jelight Company, Inc. 2 Mason Irvine, CA 92618 U.S.A Tel: +1(949) 380-8774 Fax +1(949) 768-9457 Parts Assembly FIG. 4 ® UVO Cleaner Exhaust Port Media Inlet Port Ozone Filter Removable Tray Stand-off Blower Tray Support Lamp Assembly Ozone Filter Locking Screw... -
Page 10: System Setup
System Setup Refer to Figure 3 and 4 ® 1 Unpack UVO-Cleaner 1 from shipping box and place on a sturdy level surface. 2 Do NOT plug the machine into a Socket Outlet or apply power at this time. 3 Connect Exhaust Port 6 to a suitable exhaust system capable of maintaining negative 0.1 to negative 0.5 inches [2.5mm-12.7mm] of static water pressure while in operation. -
Page 11: Lamp Installation
Jelight Company, Inc. 2 Mason Irvine, CA 92618 U.S.A Tel: +1(949) 380-8774 Fax +1(949) 768-9457 Lamp Installation Refer to Figure 4 Procedure: 1 Do NOT plug the machine into a Socket Outlet or apply power at this time. 2 Open Lid 2 . -
Page 12: System Operation
Jelight Company, Inc. 2 Mason Irvine, CA 92618 U.S.A Tel: +1(949) 380-8774 Fax +1(949) 768-9457 System Operation WARNING: • ® Follow all instructions in System Setup before applying power to the UVO Cleaner • In case of emergency, push the Emergency Stop button on the front panel and unplug the machine. -
Page 13: Scheduled Maintenance
The lamp assembly should be replaced after 5,000 to 10,000 hours of operation (for detailed instructions on lamp installation, please refer to page 11). Please contact Jelight Company Inc. for pricing and availability of replacement UV lamps, radiometer, detectors, and other components. -
Page 14: Intensity Measurement
1 Allow current cleaning cycle to complete and wait a minimum of 2 minutes for ozone to be ® removed from the UVO-Cleaner before proceeding. 2 Open the Lid and place the UV Detector in the center of the Removable Tray – see Figure 5. -
Page 15: Intensity Measurement (Continued)
Record this measurement. 12 After recording the UV measurement, press the Stop button and wait a minimum of 2 minutes for ozone to be removed. 13 Open the Lid and remove the Detector. ® 14 The UVO-Cleaner may now be turned off. -
Page 16: Troubleshooting
Recommended calibration period is 3–4 months when subjected to strong UV radiation. The photodiode located inside the detector will eventually become solarized. If solarization occurs, the detector will require replacement. For further assistance, contact Jelight Company Inc. 2 Mason, Irvine CA 92618 U.S.A. Tel: +1(949) 380-8774... -
Page 17: Limited Warranty
If the product does not qualify for warranty repair, Jelight Company, Inc. will provide an estimate of the parts, labor and shipping charges required to complete the repair and return the product. If you authorize repairs, Jelight Company, Inc. - Page 18 Jelight Company Inc. reserves the right to amend all or some of these terms and conditions at any time. Jelight Company Inc. declines all liability in the matter, as well as all responsibility for the accuracy, timeliness and/or completeness of the information contained, and for any use made of the information provided.
-
Page 19: Warranty Registration Form
We do not sell your name to third party mailing list companies. Information you provide is for the exclusive use of Jelight Company, Inc. Please complete and return this form by surface mail to Jelight Company Inc. Alternatively, you may e-mail this information to: warranty@jelight.com...