Advertisement
Quick Links
ASSEMBLY AND INSTRUCTION MANUAL (EN
This assembly and instruction manual applies to the following models
Read the instructions carefully. Use and maintenance must also be in accordance with the instructions. Questions related to installation or
use of the product should be addressed to the importer
EN
1
millclimate.com
Advertisement
Summary of Contents for MILL TG10B
- Page 1 ASSEMBLY AND INSTRUCTION MANUAL (EN This assembly and instruction manual applies to the following models Read the instructions carefully. Use and maintenance must also be in accordance with the instructions. Questions related to installation or use of the product should be addressed to the importer millclimate.com...
- Page 2 millclimate.com...
- Page 3 You must follow standard safety guidelines when using electrical products, especially in the presence of children To avoid electric shock or damage, always make sure that the plug is disconnected before the product is moved or cleaned • Read the instructions carefully. •...
- Page 4 KEEP THIS INSTRUCTION MANUAL FOR FUTURE USE NEVER TOUCH THE PRODUCT WITH WET HANDS OR COVER THE AIR OUTLET Please contact Mill International AS if any of the error codes below appear on the display Faulty temperature sensor Flashes every 30 seconds...
- Page 5 millclimate.com...
- Page 6 TG10B this is done manually Make sure that the hatch above the air outlet is in the closed position when switching the product on. (Applies only to TG20B. On TG10B this hatch must be manually opened before starting the device. millclimate.com...
- Page 7 If you wish to use the product over a longer period of continuous operation, the drainage tube may prove useful. Please follow the steps below for each model Make sure the product is turned off, unplug it from the outlet and remove the water tank Remove the outlet plug from the water tank and plug this into the water outlet (Figure 1) Use a knife to remove the protection in front of...
- Page 8 CAUTION! Selection will au- tomatically be confirmed after 5 seconds of flashing ON/OFF button. Press once to turn the product ON or OFF UP/DOWN arrow keys i) Use the arrow keys to set the desired humidity level (intervals of 5%) Timer function (counting down until the product is turned OFF) i) Press the clock once to activate the timer function Ii) Use the arrow keys to set the desired number of hours for the timer function (intervals of 1 hour)
- Page 9 Open the hatch above the air outlet and adjust it to the desired angle Press the ON/OFF button Turn off by pressing the ON/OFF button Allow the product to stand still for at least 3 minutes after it is turned off, so that any re- maining water in the system will pass down into the water tank.
- Page 10 CAUTION! Selection will au- tomatically be confirmed after 5 seconds of flashing ON/OFF button. Press once to turn the product ON or OFF Press once to start/stop the automatic air control function UP/DOWN arrow keys i) Use the arrow keys to set the desired humidity level (intervals of 5%) Timer function (counting down until the product is turned OFF) i) Press the clock once to activate the timer function Ii) Use the arrow keys to set the desired number of hours for the timer function (intervals of 1 hour)
- Page 11 Make sure that the hatch above the air outlet is closed Press the ON/OFF button once Turn off by pressing the ON/OFF button Allow the product to stand still for at least 3 minutes after it is turned off, so that any re- maining water in the system will pass down into the water tank.
-
Page 12: Troubleshooting
Troubleshooting Please go through the troubleshooting guide to identify what can be done to correct the problem. Contact Mill International AS should the problem persist The product is not receiving power Connect the plug to the socket and check The product is not switched on... -
Page 13: Clean The Air Filter
Make sure the power connector is unplugged before you wipe it with a dry cloth 1) Clean the air filter The air filter collects dust over time. This dust reduces operating efficiency and regular cleaning of the filter is required for the best possible operating efficiency Clean the filter every 1–5 days if the room is dusty. - Page 14 When submitting a claim, you have to provide the series number for your product and present the original receipt In case of claims or questions about the product or spare parts, contact your retailer or Mill International millclimate.com...
Need help?
Do you have a question about the TG10B and is the answer not in the manual?
Questions and answers