ORing Industrial Networking Corp. RGPS-92222GCP-NP-LP Quick Installation Manual

GIGABIT
PoE
SWITCH
Q I
uick nstallation
M A N A G E D
Rack-Mount

Introduction

The RGS-92222GCP-NP series , which consist of the
NP-LP and RGPS-92222GCP-NP-P models, are managed rack-mount
Ethernet switches with 22 10/100/1000Base-T(X) IEEE802.3at P.S.E.
ports, two Gigabit combo ports, and two 100/1000Base-X SFP ports. The
P.S.E-enabled ports are able to provide sufficient power for power-hungry
devices with up to 30w per port. With dual power inputs for redundancy,
the switches have an operating temperature from -40 C to 60 C.

Package Contents

Contents Pictures Number
RGPS-92222-
X 1
GCP-NP
X 1

Console Cable

X 1
CD
X 1
QIG
Screw (M4 X6) X 6
Rack-mounted
X 1
kit (L&R)
Power cord X 1

Preparation

Before you begin installing the switch, make sure you have all of the package
contents available and a PC with Microsoft Internet Explorer 6.0 or later, for
using web-based system management tools.
Safety & Warnings
Elevated Operating Ambient: If installed in a closed or multi-unit rack
assembly, the operating ambient temperature of the rack environment may be
greater than room ambient. Therefore, consideration should be given to
installing the equipment in an environment compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
Reduced Air Flow: Installation of the equipment in a rack should be such
that the amount of air flow required for safe operation of the equipment is
not compromised.
Mechanical Loading: Mounting of the equipment in the rack should be
such that a hazardous condition is not achieved due to uneven mechanical
loading.
Circuit Overloading: Consideration should be given to the connection of the
equipment to the supply circuit and the effect that overloading of the circuits
might have on overcurrent protection and supply wiring. Appropriate
consideration of equipment nameplate ratings should be used when addressing
this concern.
Q I G
RGPS-92222GCP-NP Series
RGPS-92222GCP-NP Series
G
uide

Dimension

RGPS-92222GCP-
86.5 49.0
o o
17.80
30.20 82.00
G2 G4 G6 G8 G10 G12 G14
Console
Fault
Reset R.M.
PWR Ring
G1 G3 G5 G7 G9 G11 G13

Panel Layouts

1
8 9
Console G2 G4 G6 G8 G10 G12
Fault
R.M.
Reset
PWR Ring
G1 G3 G5 G7 G9 G11
2 3 4 5 6 7
1. Console port
2. Reset button
3. Power indicator
4. Ring status LED
5. RM status LED
6. Fault indicator
7. LAN ports

Installation

Rack-mounting

Step 1: Install left and right front mounting brackets to the switch using three screws on each side.
Step 2: With front brackets orientated in front of the rack, fasten the brackets to the rack using two more
screws.
1907-2-29-RGPS92222GCPNP-1.0
25.50
20.00
431.00 35.50 8.00
5.50
G16 G18 G20 G22 G24
10/100/ G2 G8 G10 G16 G18 G24 RGPS-92222GCP-NP
1000T PoE
G1 G7 G9 G15 G17 G23
LINK/ACT
100/1000X
G15 G17 G19 G21 G23 G23 G24 G25 G26
R3.25
Front View
11 12
G14 G16 G18 G20 G22 G24
10/100/ G2 G8 G10 G16 G18 G24 RGPS-92222GCP-NP
1000T PoE
G1 G7 G9 G15 G17 G23
LINK/ACT
100/1000X
G13 G15 G17 G19 G21 G23 G23 G24 G25 G26
10 13 14
8. LED for even Ethernet ports link/act status
9. LED for odd Ethernet ports link/act status
10. First Gigabit combo port
11. Second Gigabit combo port
12. PoE status LED for LAN ports
13. SFP ports
14. LNK/ACT LED for SFP ports
Rear View
1 2
1. Power switch
2. AC power input (100V~240V
AC 100-240V
50-60HZ
PW1
/ 50~60Hz)
AC Power SWITCH
PRINTED ON RECYCLED PAPER
Managed Gigabit PoE Ethernet Switch

Network Connection

The switch provides standard Ethernet ports. According to the link type, the switch uses CAT
3,4,5,5e UTP cables to connect to any other network devices (PCs, servers, switches,
routers, or hubs). Please refer to the following table for cable specifications.
Cable Types and Specifications:
Cable Type Max. Length Connector
10BASE-T Cat. 3, 4, 5 100-ohm UTP 100 m (328 ft) RJ-45
100BASE-TX Cat. 5 100-ohm UTP UTP 100 m (328 ft) RJ-45
1000BASE-T Cat. 5 / Cat. 5e 100-ohm UTP UTP 100 m (328 ft) RJ-45
With 10/100BASE-T(X) cables, pins 1 and 2 are used for transmitting data, and pins 3 and 6 are
used for receiving data. The device also supports auto MDI/MDI-X operation. You can use a
cable to connect the switch to a PC
For pin assignments for different types of cables, please refer to the following
tables.
10/100Base-T(X) P.S.E. RJ-45 port
Pin Number Assignment
#1 TD+ with PoE Power input +
#2 TD- with PoE Power input +
#3 RD+ with PoE Power input -
#6 RD- with PoE Power input -
1000Base-T P.S.E. RJ-45 port
Pin Number Assignment
#1 BI_DA+ with PoE Power input +
#2 BI_DA- with PoE Power input +
#3 BI_DB+ with PoE Power input -
#4 BI_DC+
#5 BI_DC-
#6 BI_DB- with PoE Power input -
#7 BI_DD+
#8 BI_DD-
10/100 Base-T(X) MDI/MDI-X 1000Base-T MDI/MDI-X
Pin Number MDI port MDI-X port Pin Number MDI port MDI-X port
1 TD+(transmit) RD+(receive) 1 BI_DA+ BI_DB+
2 TD-(transmit) RD-(receive) 2 BI_DA- BI_DB-
3 RD+(receive) TD+(transmit) 3 BI_DB+ BI_DA+
4 Not used Not used 4 BI_DC+ BI_DD+
5 Not used Not used 5 BI_DC- BI_DD-
6 RD-(receive) TD-(transmit) 6 BI_DB- BI_DA-
7 Not used Not used 7 BI_DD+ BI_DC+
8 Not used Not used 8 BI_DD- BI_DC-
Console cable
Use the provided DB-9 cable (RS-232 cable) to connect the switch to a PC with the DB-9
connector attached to the switch console port and the DB-9 female connector to the PC.
PC pin out (male) RS-232 with DB9
assignment female connector
Pin #2 RD Pin #2 TD
Pin #3 TD Pin #3 RD
Pin #5 GND Pin #5 GND
Quick Installation Guide
Version 1.0