Download Print this page

TECshow NAVIGATOR SPLIT RDM User Manual

Dmx & rdm splitter - 2 inputs / 4 outputs

Advertisement

Available languages

Available languages

Quick Links

NAVIGATOR
SPLIT RDM
DMX & RDM Splitter - 2 inputs / 4 outputs
USER MANUAL / MANUAL DE USUARIO
PLEASE READ THE INSTRUCTIONS CAREFULLY BEFORE USE
POR FAVOR LEA LAS INSTRUCCIÓNES ANTES DE USAR
P. 1
| Tecshow Navigator Split RDM

Advertisement

loading

Summary of Contents for TECshow NAVIGATOR SPLIT RDM

  • Page 1 SPLIT RDM DMX & RDM Splitter - 2 inputs / 4 outputs USER MANUAL / MANUAL DE USUARIO PLEASE READ THE INSTRUCTIONS CAREFULLY BEFORE USE POR FAVOR LEA LAS INSTRUCCIÓNES ANTES DE USAR P. 1 | Tecshow Navigator Split RDM...
  • Page 2: Specifications

    Navigator Split RDM DMX & RDM Splitter - 2 inputs / 4 outputs Navigator Split RDM is a DMX & RDM splitter that features four outputs with XLR-3 & XLR-5 connec- tors, which can be connected to any of the two inputs.
  • Page 3 Never pull out This device contains no user-serviceable parts. the plug by tugging the power cord. Refer servicing to qualified technicians only. P. 3 | Tecshow Navigator Split RDM English version...
  • Page 4: Operating Determinations

    • This device falls under protection class I. There- fore it is essential to connect the yellow/green P. 4 Tecshow Navigator Split RDM | English version...
  • Page 5 7) 3/5-pin DMX signal connectors OUT 4) 3-pin DMX signal connector THROUGH Back side 8) Power switch ON/OFF 11) Ground/earth connection 9) Pro power connector IN 12) M10 clamp thread 10) Fuse 1A/250V 13) Terminal resistor P. 5 | Tecshow Navigator Split RDM English version...
  • Page 6 1) Fasten the distributor to a 19-inch rack. before the whole system is set up and connected 2) Use a 3-pin/5-pin XLR cable to connect the Navi- properly. gator Split RDM and other devices. P. 6 Tecshow Navigator Split RDM | English version...
  • Page 7 Connecting more than 30 fixtures on one serial data link without the 6. MAINTENANCE The Navigator Split RDM requires almost no main- what so ever. If this happens, follow the directions tenance. However, you should keep the unit clean.
  • Page 8: Troubleshooting

    1) Power supply. Check that the unit is plugged into DMX card malfunction. an appropriate power supply. 1) Check the DMX setting. Make sure that DMX ad- 2) The splitter. Return Navigator Split RDM to your dresses are correct. dealer. 2) Check the DMX cable: Unplug the unit; change 3) The fuse.
  • Page 9 ■ Disconnect fixture. Check set- The power supply settings do not match local AC voltage and tings and correct if necessary frequency Design and product specifications are subject to change without prior notice. P. 9 English version | Tecshow Navigator Split RDM...
  • Page 10 1. DESCRIPCIÓN Navigator Split RDM Splitter DMX & RDM - 2 entradas / 4 salidas Navigator Split RDM es un splitter DMX y RDM que tiene cuatro salidas con conectores XLR-3 y XLR-5, las cuales pueden ser conectadas a cualquiera de las dos entradas que también posee.
  • Page 11 En caso de precisar asistencia, antes de operar el equipo. póngase en contacto con un profesional idóneo. • Instale el equipo a una distancia mínima de 50 P. 11 Versión Español | Tecshow Navigator Split RDM...
  • Page 12 Mantenga la unidad alejada del alcance de Plateado Neutro A los niños. No deje la unidad en funcionamiento Verde Tierra y sin supervisión. • Utilice repuestos originales y del mismo tipo en P. 12 Tecshow Navigator Split RDM | Versión Español...
  • Page 13 4) Conector thru DMX XLR-3. Vista trasera 8) Interruptor de encendido/apagado. 11) Conexión a tierra. 9) Conector de entrada Pro power. 12) Orificio M10 para abrazadera. 10) Fusible 1A/250 V. 13) Resistencia terminal P. 13 Versión Español | Tecshow Navigator Split RDM...
  • Page 14 Modos de control las unidades necesarias. 5) Conecte las unidades de iluminación a las salidas Varios splitters RDM (DMX) DMX del equipo. 1) Coloque la unidad en un bastidor estándar de 19 P. 14 Tecshow Navigator Split RDM | Versión Español...
  • Page 15 6. MANTENIMIENTO Navigator Split RDM es un equipo que práctica- queme el fusible. Para reemplazarlo, siga los pasos mente no requiere de mantenimiento. Sin em- a continuación: bargo, se recomienda mantener la unidad limpia.
  • Page 16 ■ Revise las conexiones y los Conexión de datos con fallas. cables. Corrija las conexiones de los cables. Reemplace o repare los cables dañados. P. 16 Tecshow Navigator Split RDM | Versión Español...
  • Page 17 Observación: El proveedor no asumirá responsabilidad por los errores u omisiones del manual. La información de este manual está sujeta a cambios sin previo aviso. P. 17 | Tecshow Navigator Split RDM Versión Español...
  • Page 18 FOR MORE INFO ON THIS PRODUCT PLEASE CHECK WWW.TEC-SHOW.COM / PARA MAS INFORMACION SOBRE ESTE PRODUCTO VISITE WWW.TEC-SHOW.COM P. 18 Tecshow Navigator Split RDM |...